T113-s3 MIPI适配无法点亮
-
按照下面的配置,没有背光,而且屏幕排线很烫,屏幕没有温度,尝试关闭了UBOOT,仅保留内核的,发现还是一样。
&lcd0 { lcd_used = <1>; // lcd_driver_name = "ili9881c_dsi_panel"; lcd_driver_name = "tft08006"; lcd_backlight = <150>; lcd_if = <4>; lcd_x = <800>; lcd_y = <1280>; lcd_width = <52>; lcd_height = <52>; lcd_pwm_used = <1>; //pw7 lcd_pwm_ch = <7>; lcd_pwm_freq = <5000>; lcd_pwm_pol = <0>; lcd_pwm_max_limit = <255>; lcd_dclk_freq = <71>; // 传输像素传送频率(MHZ) // 水平同步参数 lcd_hbp = <48>; // (Horizontal Back Porch THB) lcd_ht = <908>; // (Horizontal Total THT) lcd_hspw = <8>; // (Horizontal Synchronization THS) lcd_hfp = <52>; // (Horizontal Front Porch THF) // 垂直同步参数 lcd_vbp = <16>; // (Vertical Back Porch TVB) lcd_vt = <1317>; // (Vertical Total(1) TVT) lcd_vspw = <6>; // (Vertical Synchronization TVS) lcd_vfp = <15>; // (Vertical Front Porch TVF) lcd_dsi_if = <0>; lcd_dsi_lane = <4>; lcd_lvds_if = <0>; lcd_lvds_colordepth = <0>; lcd_lvds_mode = <0>; lcd_frm = <0>; lcd_hv_clk_phase = <0>; lcd_hv_sync_polarity= <0>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_cmap_en = <0>; lcd_fsync_en = <0>; lcd_fsync_act_time = <1000>; lcd_fsync_dis_time = <1000>; lcd_fsync_pol = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; // reset // lcd_gpio_0 = <&pio PB 4 GPIO_ACTIVE_HIGH>; lcd_gpio_0 = <&pio PD 22 1 0 3 1>; lcd_power = "vcc-lcd"; lcd_pin_power = "vcc-pd"; // pinctrl-0 = <&dsi4lane_pins_a>; // pinctrl-1 = <&dsi4lane_pins_b>; status = "okay"; };
[19]HELLO! BOOT0 is starting! [22]BOOT0 commit : 32dc611 [25]set pll start [30]periph0 has been enabled [33]set pll end [35][pmu]: bus read error [37]board init ok [39]ZQ value = 0x30 [41]get_pmu_exist() = -1 [44]ddr_efuse_type: 0xa [46]trefi:7.8ms [48][AUTO DEBUG] single rank and full DQ! [52]ddr_efuse_type: 0xa [55]trefi:7.8ms [57][AUTO DEBUG] rank 0 row = 13 [60][AUTO DEBUG] rank 0 bank = 8 [63][AUTO DEBUG] rank 0 page size = 2 KB [67]DRAM BOOT DRIVE INFO: V0.33 [70]DRAM CLK = 936 MHz [72]DRAM Type = 3 (2:DDR2,3:DDR3) [75]DRAMC read ODT off. [78]DRAM ODT value: 0x42. [80]ddr_efuse_type: 0xa [83]DRAM SIZE =128 M [85]dram_tpr4:0x0 [87]PLL_DDR_CTRL_REG:0xf8004d00 [90]DRAM_CLK_REG:0xc0000000 [93][TIMING DEBUG] MR2= 0x20 [100]DRAM simple test OK. [103]rtc standby flag is 0x0, super standby flag is 0x0 [108]dram size =128 [111]card no is 0 [112]sdcard 0 line count 4 [115][mmc]: mmc driver ver 2021-05-21 14:47 [124][mmc]: Wrong media type 0x0 [127][mmc]: ***Try SD card 0*** [136][mmc]: HSSDR52/SDR25 4 bit [139][mmc]: 50000000 Hz [141][mmc]: 29820 MB [143][mmc]: ***SD/MMC 0 init OK!!!*** [230]Loading boot-pkg Succeed(index=0). [234]Entry_name = u-boot [240]Entry_name = optee [244]Entry_name = dtb [247]mmc not para [249]Jump to second Boot. M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm [00.326]smc_tee_inform_fdt failed with: ffff000a [00.332][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.337][mmc]: get sdc_type fail and use default host:tm1. [00.344][mmc]: can't find node "mmc0",will add new node [00.348][mmc]: fdt err returned <no error> [00.352][mmc]: Using default timing para [00.356][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.374][mmc]: card_caps:0x3000000a [00.377][mmc]: host_caps:0x3000003f [00.425]Item0 (Map) magic is bad [00.428]the secure storage item0 copy0 magic is bad [00.444]Item0 (Map) magic is bad [00.447]the secure storage item0 copy1 magic is bad [00.451]Item0 (Map) magic is bad [00.454]secure storage read widevine fail with:-1 [00.458]secure storage read ec_key fail with:-1 [00.463]secure storage read ec_cert1 fail with:-1 [00.467]secure storage read ec_cert2 fail with:-1 [00.472]secure storage read ec_cert3 fail with:-1 [00.476]secure storage read rsa_key fail with:-1 [00.480]secure storage read rsa_cert1 fail with:-1 [00.485]secure storage read rsa_cert2 fail with:-1 [00.489]secure storage read rsa_cert3 fail with:-1 [00.494]out of usb burn from boot: not need burn key [01.694]no vendor_boot partition is found [01.703]Starting kernel ... [01.705][mmc]: MMC Device 2 not found [01.709][mmc]: mmc 2 not find, so not exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (ubuntu@ubuntu2004) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #178 SMP PREEMPT Sun Aug 25 19:14:24 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 8 MiB at 0x47800000 [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440 [ 0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.07-00001-gcf16a914-dirty(08/25/2024-15:13:30) androidboot.dramsize=128 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 108584K/131072K available (6144K kernel code, 295K rwdata, 1656K rodata, 1024K init, 1163K bss, 14296K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implemeU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x26c/0x3ec with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008008] Switching to timer-based delay loop, resolution 41ns [ 0.014186] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.023868] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) 32768 minimum: 301 [ 0.038978] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.046302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054616] CPU: Testing write buffer coherency: ok [ 0.059830] /cpus/cpu@0 missing clock-frequency property [ 0.065155] /cpus/cpu@1 missing clock-frequency property [ 0.070493] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.076635] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.083313] rcu: Hierarchical SRCU implementation. [ 0.088518] smp: Bringing up secondary CPUs ... [ 0.094152] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.094273] smp: Brought up 1 node, 2 CPUs [ 0.104095] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.110299] CPU: All CPU(s) started in SVC mode. [ 0.115364] devtmpfs: initialized [ 0.129843] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.137940] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.147821] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.155042] pinctrl core: initialized pinctrl subsystem [ 0.161209] NET: Registered protocol family 16 [ 0.167114] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.198325] rtc_ccu: sunxi ccu init OK [ 0.204334] ccu: sunxi ccu init OK [ 0.208143] r_ccu: sunxi ccu init OK [ 0.229619] sun6i-dma 3002000.dma-controller: sunxi dma probed [ 0.236866] reg-fixed-voltage vdd-cpu: Fixed regulator specified with variable voltages [ 0.244956] reg-fixed-voltage: probe of vdd-cpu failed with error -22 [ 0.251771] iommu: Default domain type: Translated [ 0.256855] sunxi iommu: irq = 24 [ 0.261001] SCSI subsystem initialized [ 0.264992] usbcore: registered new interface driver usbfs [ 0.270565] usbcore: registered new interface driver hub [ 0.275958] usbcore: registered new device driver usb [ 0.281814] Advanced Linux Sound Architecture Driver Initialized. [ 0.288624] Bluetooth: Core ver 2.22 [ 0.292276] NET: Registered protocol family 31 [ 0.296713] Bluetooth: HCI device and connection manager initialized [ 0.303113] Bluetooth: HCI socket layer initialized [ 0.307997] Bluetooth: L2CAP socket layer initialized [ 0.313081] Bluetooth: SCO socket layer initialized [ 0.318221] pwm module init! [ 0.322222] g2d 5410000.g2d: Adding to iommu group 0 [ 0.327536] G2D: rcq version initialized.major:251 [ 0.333063] clocksource: Switched to clocksource arch_sys_counter [ 0.347446] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.356665] NET: Registered protocol family 2 [ 0.361562] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.369983] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.377675] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.384763] TCP: Hash tables configured (established 1024 bind 1024) [ 0.391214] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.397794] UDP-Lite hash table entries: 256 ( 0.404969] NET: Registered protocol family 1 [ 0.410274] sun8iw20-pinctrl 2000000.pinctrl: found, using dummy regulator [ 0.420558] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.427282] sunxi_spi_resource_get()2438 - [spi0] SPI MASTER MODE [ 0.433437] sunxi_spi_resource_get()2476 - Failed to get sample mode [ 0.439799] sunxi_spi_resource_get()2[ 0.446255] sunxi_spi_resource_get()2485 - sample_mode:-1431633921 sample_delay:-1431633921 [ 0.454682] sunxi_spi_clk_init()2527 - [spi0] mclk 100000000 [ 0.460976] sunxi_spi_probe()2978 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 0.470519] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.481839] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.487870] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.522020] io scheduler mq-deadline registered [ 0.526587] io scheduler kyber registered [ 0.531560] [DISP]disp_module_init [ 0.535511] disp 5000000.disp: Adding to iommu group 0 [ 0.552306] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator [ 0.560889] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator [ 0.574219] [DISP] disp_init_hdmi,line:1047: [ 0.574223] dont support hdmi [ 0.581785] display_fb_request,fb_id:0 [ 0.591332] [DISP] Fb_copy_boot_fb,line:1445: [ 0.591336] no boot_fb0 [ 0.598641] disp_al_manager_apply ouput_type:0 [ 0.603351] [DISP]disp_module_init finish [ 0.603457] [DISP] lcd_clk_config,line:774: [ 0.603467] disp 0, clk: pll(426000000),clk(426000000),dclk(71000000) dsi_rate(71000000) [ 0.603467] clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000) [ 0.608295] sunxi_sid_init()783 - insmod ok [ 0.633290] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 0.643425] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.650527] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.658400] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n [ 0.666412] printk: console [ttyS0] enabled [ 0.666412] printk: console [ttyS0] enabled [ 0.675267] printk: bootconsole [earlycon0] disabled [ 0.675267] printk: bootconsole [earlycon0] disabled [ 0.686505] misc dump reg init [ 0.690821] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 0.701931] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 0.709149] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 0.716433] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 0.723814] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 0.730306] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 0.737208] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 0.744888] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 0.752676] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 0.760741] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 0.768308] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 0.775032] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 0.782502] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0 [ 0.790608] dma-buf: Running sanitycheck [ 0.795001] dma-buf: Running dma_fence [ 0.799168] sizeof(dma_fence)=48 [ 0.802852] dma-buf: Running dma_fence/sanitycheck [ 0.808240] dma-buf: Running dma_fence/test_signaling [ 0.813880] dma-buf: Running dma_fence/test_add_callback [ 0.819799] dma-buf: Running dma_fence/test_late_add_callback [ 0.826220] dma-buf: Running dma_fence/test_rm_callback [ 0.832032] dma-buf: Running dma_fence/test_late_rm_callback [ 0.838346] dma-buf: Running dma_fence/test_status [ 0.843684] dma-buf: Running dma_fence/test_error [ 0.848923] dma-buf: Running dma_fence/test_wait [ 0.854075] dma-buf: Running dma_fence/test_wait_timeout [ 0.893073] dma-buf: Running dma_fence/test_stub [ 0.898222] dma-buf: Running dma_fence/race_signal_callback [ 0.953316] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.973212] [DISP] disp_device_attached_and_enable,line:233: [ 0.973217] attached ok, mgr0<-->dev0 [ 0.983624] thread_signal_callback[0] completed 30652 passes, 48 misses [ 0.991036] thread_signal_callback[1] completed 38417 passes, 7812 misses [ 0.991063] [DISP] disp_device_attached_and_enable,line:236: [ 0.991072] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8 [ 1.083080] thread_signal_callback[0] completed 43397 passes, 43397 misses [ 1.090765] thread_signal_callback[1] completed 43417 passes, 43415 misses [ 1.099184] spi-nand: probe of spi0.0 failed with error -5 [ 1.105348] Error: Driver 'spi-nand' is already registered, aborting... [ 1.113041] libphy: Fixed MDIO Bus: probed [ 1.118099] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.125379] sunxi-ehci: EHCI SUNXI driver [ 1.130215] get ehci0-controller wakeup-source is fail. [ 1.136149] sunxi ehci0-controller don't init wakeup source [ 1.142355] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b65180, 0x:c8830000, irq_no:36 [ 1.154521] sunxi-ehci 4101000.ehci0-controller: 4101000.ehci0-controller supply hci not found, using dummy regulator [ 1.166703] sunxi-ehci 4101000.ehci0-controller: EHCI Host Controller [ 1.173975] sunxi-ehci 4101000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 1.183946] sunxi-ehci 4101000.ehci0-controller: irq 54, io mem 0x04101000 [ 1.213088] sunxi-ehci 4101000.ehci0-controller: USB 2.0 started, EHCI 1.00 [ 1.221632] hub 1-0:1.0: USB hub found [ 1.225866] hub 1-0:1.0: 1 port detected [ 1.230919] get ehci1-controller wakeup-source is fail. [ 1.236872] sunxi ehci1-controller don't init wakeup source [ 1.243097] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b656a0, 0x:c8836000, irq_no:38 [ 1.255240] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator [ 1.267428] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 1.274644] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 2 [ 1.284510] sunxi-ehci 4200000.ehci1-controller: irq 56, io mem 0x04200000 [ 1.313090] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 1.321637] hub 2-0:1.0: USB hub found [ 1.325878] hub 2-0:1.0: 1 port detected [ 1.330817] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.337769] sunxi-ohci: OHCI SUNXI driver [ 1.342654] get ohci0-controller wakeup-source is fail. [ 1.348608] sunxi ohci0-controller don't init wakeup source [ 1.354828] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b65410 [ 1.364628] sunxi-ohci 4101400.ohci0-controller: 4101400.ohci0-controller supply hci not found, using dummy regulator [ 1.376813] sunxi-ohci 4101400.ohci0-controller: OHCI Host Controller [ 1.384071] sunxi-ohci 4101400.ohci0-controller: new USB bus registered, assigned bus number 3 [ 1.393892] sunxi-ohci 4101400.ohci0-controller: irq 55, io mem 0x04101400 [ 1.467878] hub 3-0:1.0: USB hub found [ 1.472087] hub 3-0:1.0: 1 port detected [ 1.477120] get ohci1-controller wakeup-source is fail. [ 1.483102] sunxi ohci1-controller don't init wakeup source [ 1.489308] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b65930 [ 1.499160] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator [ 1.511346] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 1.518587] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 4 [ 1.528309] debugfs: Directory 'sunxi-ohci' with parent 'ohci' already present! [ 1.536561] sunxi-ohci 4200400.ohci1-controller: irq 57, io mem 0x04200400 [ 1.617848] hub 4-0:1.0: USB hub found [ 1.622061] hub 4-0:1.0: 1 port detected [ 1.627073] usbcore: registered new interface driver cdc_acm [ 1.633399] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.642439] usbcore: registered new interface driver usb-storage [ 1.650114] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.660794] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.671803] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.677475] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.688063] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:15 UTC (15) [ 1.696992] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 1.702766] i2c /dev entries driver [ 1.706752] sunxi cedar version 1.1 [ 1.710778] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.717076] VE: sunxi_cedar_probe power-domain init!!! [ 1.722813] VE: install start!!! [ 1.722813] [ 1.728289] VE: cedar-ve the get irq is 40 [ 1.728289] [ 1.734747] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval) [ 1.734747] [ 1.743972] VE: install end!!! [ 1.743972] [ 1.749006] VE: sunxi_cedar_probe [ 1.752915] Bluetooth: HCI UART driver ver 2.3 [ 1.757881] Bluetooth: HCI UART protocol H4 registered [ 1.763610] Bluetooth: HCI UART protocol BCSP registered [ 1.769832] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 1.778460] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40) [ 1.788272] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.794443] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.800740] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.807149] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.813559] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.820049] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.826552] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.833038] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.840281] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.851376] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.871476] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.895649] sunxi-mmc 4020000.sdmmc: detmode:gpio polling [ 1.901674] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.913675] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40) [ 1.923480] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 1.929628] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 1.936043] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 1.942469] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 1.948906] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 1.950159] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.955430] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 1.973475] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 1.979975] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 1.986496] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.986506] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 2.007455] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.007967] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.018571] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 2.050214] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.068467] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.074370] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 2.084197] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.084951] exFAT: Version 1.3.0 [ 2.095670] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 2.095742] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.099828] usbcore: registered new interface driver snd-usb-audio [ 2.106121] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 2.124737] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.131532] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.143252] mmc0: new high speed SDHC card at address 0001 [ 2.156257] [AUDIOCODEC][sunxi_codec_parse_params][2437]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 2.156257] [ 2.161780] mmcblk0: mmc0:0001 SD 29.1 GiB [ 2.178147] [AUDIOCODEC][sunxi_codec_parse_params][2473]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 2.194137] [AUDIOCODEC][sunxi_internal_codec_probe][2634]:codec probe finished [ 2.195252] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.203402] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 2.216140] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.223633] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 2.230347] [SNDCODEC][sunxi_card_init][583]:card init finished [ 2.235108] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.248899] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 2.258708] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.266267] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.272990] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.273316] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0 [ 2.295940] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished [ 2.304264] NET: Registered protocol family 10 [ 2.310153] Segment Routing with IPv6 [ 2.314283] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch [ 2.321634] NET: Registered protocol family 17 [ 2.326763] Bluetooth: RFCOMM TTY layer initialized [ 2.332201] Bluetooth: RFCOMM socket layer initialized [ 2.337973] Bluetooth: RFCOMM ver 1.11 [ 2.342744] Registering SWP/SWPB emulation handler [ 2.362147] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 2.373475] sunxi-i2c sunxi-i2c0: sunxi-i2c0 supply twi not found, using dummy regulator [ 2.383255] sunxi-i2c sunxi-i2c0: probe success [ 2.388725] sunxi-i2c sunxi-i2c1: sunxi-i2c1 supply twi not found, using dummy regulator [ 2.398438] sunxi-i2c sunxi-i2c1: probe success [ 2.405194] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator [ 2.418421] clk: Not disabling unused clocks [ 2.423335] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.432945] cfg80211: failed to load regulatory.db [ 2.433088] ALSA device list: [ 2.441576] #0: audiocodec [ 2.444824] alloc_fd: slot 0 not NULL! [ 2.452913] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.462965] devtmpfs: mounted [ 2.468193] Freeing unused ke[ 2.483228] Run /pseudo_init as init process mount: mounting none on /dev failed: Resource busy mount: mounting /dev/by-name/rootfs_data on /overlay failed: Invalid argument Mount Failed: formating /dev/by-name/rootfs_data to ext4 ... /pseudo_init: line 403: mkfs.ext4: not found can't run '/etc/preinit': No such file or directory mount: mounting proc on /proc failed: Resource busy mount: mounting tmpfs on /run failed: No such file or directory hostname: can't open '/etc/hostname': No such file or directory ------run rc.preboot file----- /etc/init.d/rcS: line 152: mkfs.ext4: not found ------run rc.modules file----- ------run rc.final file----- numid=30,iface=MIXER,name='Headphone Switch' ; type=BOOLEAN,access=rw------,values=1 : values=on BusyBox v1.27.2 () built-in shell (ash) ------run profile file----- _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! -------[ 2.864952] file system registered --------------------------------------- Tina Linux (Neptune, 61CC0487) ---------------------------------------------- Mon Feb 6 00:00:00 GMT 2023 nodev debugfs root@TinaLinux:/# [ 2.883885] configfs-gadget 4100000.udc-controller: failed to start g1: -19 sh: write error: No such device [ 2.896660] random: fast init done [ 2.909919] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator [ 2.921958] 8<--- cut here --- [ 2.925399] Unable to handle kernel NULL pointer dereference at virtual address 00000290 [ 2.934445] pgd = (ptrval) [ 2.937455] [00000290] *pgd=00000000 [ 2.941433] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 2.947339] Modules linked in: [ 2.950734] CPU: 1 PID: 178 Comm: cat Not tainted 5.4.61 #178 [ 2.957122] Hardware name: Generic DT based system [ 2.962456] PC is at typec_set_data_role+0x0/0x3c [ 2.967691] LR is at usb_msg_center+0x128/0x220 [ 2.972725] pc : [<c0484870>] lr : [<c047d258>] psr: 60000013 [ 2.979696] sp : c5dafc30 ip : c5daa0d8 fp : 00000000 [ 2.985508] r10: c5d29900 r9 : c633aa00 r8 : 00000000 [ 2.991315] r7 : c0b66ab0 r6 : c5dae000 r5 : 00000000 r4 : c0b66bc8 [ 2.998572] r3 : 00000000 r2 : 0e22738e r1 : 00000000 r0 : 00000000 [ 3.005834] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 3.013775] Control: 10c5387d Table: 45d4c06a DAC: 00000051 [ 3.020168] Process cat (pid: 178, stack limit = 0x(ptrval)) [ 3.026465] Stack: (0xc5dafc30 to 0xc5db0000) [ 3.031311] fc20: c0b66ab0 00000000 00000000 0e22738e [ 3.040410] fc40: c5cbe000 c0a2ed20 c072e004 c5cbe000 c717d410 c047c4e0 c0a2ed7c c047c498 [ 3.049514] fc60: c072e004 c03ceeac 00001000 c5d01000 c072e004 c022de34 c5d01000 00001000 [ 3.058612] fc80: 00000000 00000001 c5dafda0 c5d1f000 c5d29900 c01efcac 00000000 c633ac00 [ 3.067718] fca0: c5d01018 c5d01030 c5d29900 00000000 00001000 c5dafd1c c5d29900 c5dafda0 [ 3.076816] fcc0: 00000000 c022c994 bf000000 c01cd2d0 00000000 c5d29900 c5dafd1c c5dafda0 [ 3.085923] fce0: 00000000 c5d29900 ffffe000 c01ce810 00000000 c5dafd1c c5dae000 00010000 [ 3.095022] fd00: c5dafd1c c5d29900 c5dafda0 c01cf644 c5dafd18 c5dafd1c c633ac00 00000008 [ 3.104132] fd20: 00000000 00010000 c633ac00 00000010 c5dae000 c5dafd9c c5dafd98 c032a7b4 [ 3.113234] fd40: c5dafd9c 00000001 00000000 c6dd0f28 c6dd0ed8 00000000 c5dafe80 00000000 [ 3.122335] fd60: 00000000 0e22738e c5dafe80 00010000 c5dafec0 0e22738e 00000010 c5dafdc4 [ 3.131439] fd80: 00000000 c5dae000 c5dafe88 c01f7024 00000000 00000000 c5d3d240 00000000 [ 3.140541] fda0: 00000000 00000000 00000001 00000020 00000000 00010000 c633aa80 00000000 [ 3.149635] fdc0: 00000000 c5d1f000 00001000 c5d43000 00001000 c5d6a000 00001000 c5d2b000 [ 3.158737] fde0: 00001000 c5d1e000 00001000 c5d6f000 00001000 c5cf0000 00001000 c5cf2000 [ 3.167832] fe00: 00001000 c5d79000 00001000 c5cdc000 00001000 c5cec000 00001000 c5cd9000 [ 3.176932] fe20: 00001000 c5ce9000 00001000 c5d78000 00001000 c5d1b000 00001000 c5da8000 [ 3.186032] fe40: 00001000 0e22738e c5dafe88 c633aa80 c5dafec0 00000000 01000000 c5d29900 [ 3.195132] fe60: 00000000 00000000 c01f75cc c01f6290 00000000 c6dda700 00000000 00000000 [ 3.204233] fe80: 00010001 c5dafe84 00000000 00000000 00000048 0e22738e c5dae000 c5dae000 [ 3.213335] fea0: c5d1d900 01000000 c5daff20 c5daff28 c5d29900 7fffffff 00000000 c01f641c [ 3.222440] fec0: 01000000 01000000 00000000 c5d1d900 00000000 00000000 c5daff28 00000000 [ 3.231545] fee0: 00000000 00000000 beecb000 0e22738e c5d4efb8 c5d1d900 c5d29900 01000000 [ 3.240651] ff00: c5dae000 00000000 c5daff28 c01cec94 01000000 00000000 00000000 c7214620 [ 3.249752] ff20: 00000000 00000000 00000000 00000000 00000000 c5d29900 00000000 c5d1d900 [ 3.258859] ff40: 00000000 0e22738e c63ff240 01000000 c5dae000 00000000 00000000 c0101228 [ 3.267960] ff60: c5dae000 000000ef beecbc64 c01cfadc 7fffffff 00000000 00000001 beeccd24 [ 3.277057] ff80: 00000000 0e22738e 00000000 01000000 00000000 00000003 000000ef c0101228 [ 3.286158] ffa0: c5dae000 c0101000 01000000 00000000 00000001 00000003 00000000 01000000 [ 3.295257] ffc0: 01000000 00000000 00000003 000000ef 00000003 00000001 00000000 beecbc64 [ 3.304357] ffe0: 00520f30 beecbc54 004c154c b6fa9814 60000010 00000001 00000000 00000000 [ 3.313465] [<c0484870>] (typec_set_data_role) from [<00000000>] (0x0) [ 3.320728] Code: e8bd8010 c0b66d2c c03cec74 c03cec58 (e5903290) [ 3.327638] ---[ end trace 26caefabc296ed5f ]--- Segmentation fault [ 3.336755] read descriptors [ 3.339975] read strings
-
改了一些小问题,把报错去了去,但是我发现在没有插屏幕FPC排线到板子上,我的usb还能用,接上排线之后 就用不了了,
[19]HELLO! BOOT0 is starting! [22]BOOT0 commit : 32dc611 [25]set pll start [30]periph0 has been enabled [33]set pll end [35][pmu]: bus read error [37]board init ok [39]ZQ value = 0x30 [41]get_pmu_exist() = -1 [44]ddr_efuse_type: 0xa [46]trefi:7.8ms [48][AUTO DEBUG] single rank and full DQ! [52]ddr_efuse_type: 0xa [55]trefi:7.8ms [57][AUTO DEBUG] rank 0 row = 13 [60][AUTO DEBUG] rank 0 bank = 8 [63][AUTO DEBUG] rank 0 page size = 2 KB [67]DRAM BOOT DRIVE INFO: V0.33 [70]DRAM CLK = 936 MHz [72]DRAM Type = 3 (2:DDR2,3:DDR3) [75]DRAMC read ODT off. [78]DRAM ODT value: 0x42. [80]ddr_efuse_type: 0xa [84]DRAM SIZE =128 M [85]dram_tpr4:0x0 [87]PLL_DDR_CTRL_REG:0xf8004d00 [90]DRAM_CLK_REG:0xc0000000 [93][TIMING DEBUG] MR2= 0x20 [100]DRAM simple test OK. [103]rtc standby flag is 0x0, super standby flag is 0x0 [108]dram size =128 [111]card no is 0 [112]sdcard 0 line count 4 [115][mmc]: mmc driver ver 2021-05-21 14:47 [124][mmc]: Wrong media type 0x0 [127][mmc]: ***Try SD card 0*** [137][mmc]: HSSDR52/SDR25 4 bit [139][mmc]: 50000000 Hz [142][mmc]: 29820 MB [144][mmc]: ***SD/MMC 0 init OK!!!*** [230]Loading boot-pkg Succeed(index=0). [234]Entry_name = u-boot [240]Entry_name = optee [244]Entry_name = dtb [247]mmc not para [249]Jump to second Boot. M/TC: OP-TEE version: 6aef7bb2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Jul 23 09:25:11 UTC 2021 arm [00.326]smc_tee_inform_fdt failed with: ffff000a [00.332][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [00.337][mmc]: get sdc_type fail and use default host:tm1. [00.344][mmc]: can't find node "mmc0",will add new node [00.348][mmc]: fdt err returned <no error> [00.352][mmc]: Using default timing para [00.356][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.374][mmc]: card_caps:0x3000000a [00.377][mmc]: host_caps:0x3000003f [00.425]Item0 (Map) magic is bad [00.428]the secure storage item0 copy0 magic is bad [00.444]Item0 (Map) magic is bad [00.447]the secure storage item0 copy1 magic is bad [00.451]Item0 (Map) magic is bad [00.454]secure storage read widevine fail with:-1 [00.459]secure storage read ec_key fail with:-1 [00.463]secure storage read ec_cert1 fail with:-1 [00.467]secure storage read ec_cert2 fail with:-1 [00.472]secure storage read ec_cert3 fail with:-1 [00.476]secure storage read rsa_key fail with:-1 [00.480]secure storage read rsa_cert1 fail with:-1 [00.485]secure storage read rsa_cert2 fail with:-1 [00.489]secure storage read rsa_cert3 fail with:-1 [00.494]out of usb burn from boot: not need burn key [01.694]no vendor_boot partition is found [01.703]Starting kernel ... [01.705][mmc]: MMC Device 2 not found [01.709][mmc]: mmc 2 not find, so not exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (ubuntu@ubuntu2004) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #186 SMP PREEMPT Sun Aug 25 21:38:59 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 8 MiB at 0x47800000 [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0n firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440 [ 0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/pseudo_init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.07-00001-gcf16a914-dirty(08/25/2024-18:03:00) androidboot.dramsize=128 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 108584K/131072K available (6144K kernel code, 295K rwdata, 1656K rodata, 1024K init, 1163K bss, 14296K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x26c/0x3ec with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008016] Switching to timer-based delay loop, resolution 41ns [ 0.014194] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.023893] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.034251] pid_max: default: 32768 minimum: 301 [ 0.038984] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.046309] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054634] CPU: Testing write buffer coherency: ok [ 0.059843] /cpus/cpu@0 missing clock-frequency property [ 0.065161] /cpus/cpu@1 missing clock-frequency property [ 0.070499] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.076637] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.083303] rcu: Hierarchical SRCU implementation. [ 0.088525] smp: Bringing up secondary CPUs ... [ 0.094139] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.094258] smp: Brought up 1 node, 2 CPUs [ 0.104071] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.110241] CPU: All CPU(s) started in SVC mode. [ 0.115305] devtmpfs: initialized [ 0.129700] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.137817] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.147690] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.154915] pinctrl core: initialized pinctrl subsystem [ 0.161082] NET: Registered protocol family 16 [ 0.166964] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.198051] rtc_ccu: sunxi ccu init OK [ 0.204066] ccu: sunxi ccu init OK [ 0.207873] r_ccu: sunxi ccu init OK [ 0.229403] sun6i-dma 3002000.dma-controller: sunxi dma probed [ 0.236638] reg-fixed-voltage vdd-cpu: Fixed regulator specified with variable voltages [ 0.244721] reg-fixed-voltage: probe of vdd-cpu failed with error -22 [ 0.251511] iommu: Default domain type: Translated [ 0.256595] sunxi iommu: irq = 24 [ 0.260723] SCSI subsystem initialized [ 0.264712] usbcore: registered new interface driver usbfs [ 0.270278] usbcore: registered new interface driver hub [ 0.275660] usbcore: registered new device driver usb [ 0.281529] Advanced Linux Sound Architecture Driver Initialized. [ 0.288371] Bluetooth: Core ver 2.22 [ 0.291996] NET: Registered protocol family 31 [ 0.296442] Bluetooth: HCI device and connection manager initialized [ 0.302849] Bluetooth: HCI socket layer initialized [ 0.307740] Bluetooth: L2CAP socket layer initialized [ 0.312815] Bluetooth: SCO socket layer initialized [ 0.317954] pwm module init! [ 0.321917] g2d 5410000.g2d: Adding to iommu group 0 [ 0.327196] G2D: rcq version initialized.major:251 [ 0.332766] clocksource: Switched to clocksource arch_sys_counter [ 0.347130] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.356324] NET: Registered protocol family 2 [ 0.361255] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.369676] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.377382] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.384452] TCP: Hash tables configured (established 1024 bind 1024) [ 0.390902] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.397465] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.404633] NET: Registered protocol family 1 [ 0.409951] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 0.420240] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.426971] sunxi_spi_resource_get()2438 - [spi0] SPI MASTER MODE [ 0.433136] sunxi_spi_resource_get()2476 - Failed to get sample mode [ 0.439490] sunxi_spi_resource_get()2481 - Failed to get sample delay [ 0.445945] sunxi_spi_resource_get()2485 - sample_mode:-1431633921 sample_delay:-1431633921 [ 0.454363] sunxi_spi_clk_init()2527 - [spi0] mclk 100000000 [ 0.460672] sunxi_spi_probe()2978 - [spi0]: driver probe succeed, base c881f000, irq 39 [ 0.470222] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.481553] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.487591] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.521229] io scheduler mq-deadline registered [ 0.525805] io scheduler kyber registered [ 0.530782] [DISP]disp_module_init [ 0.534685] disp 5000000.disp: Adding to iommu group 0 [ 0.551442] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator [ 0.560030] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator [ 0.573666] display_fb_request,fb_id:0 [ 0.583239] [DISP] Fb_copy_boot_fb,line:1445: [ 0.583243] no boot_fb0 [ 0.590486] disp_al_manager_apply ouput_type:0 [ 0.593044] [DISP]disp_module_init finish [ 0.595361] [DISP] lcd_clk_config,line:774: [ 0.595372] disp 0, clk: pll(426000000),clk(426000000),dclk(71000000) dsi_rate(71000000) [ 0.595372] clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000) [ 0.599862] sunxi_sid_init()783 - insmod ok [ 0.624913] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 0.635092] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.642199] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI [ 0.650074] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n [ 0.658063] printk: console [ttyS0] enabled [ 0.658063] printk: console [ttyS0] enabled [ 0.666975] printk: bootconsole [earlycon0] disabled [ 0.666975] printk: bootconsole [earlycon0] disabled [ 0.678261] misc dump reg init [ 0.682591] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 0.693790] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 0.701039] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 0.708395] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 0.715836] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 0.722379] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 0.729334] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 0.737081] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 0.744947] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 0.753078] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 0.760702] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 0.767486] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 0.775039] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0 [ 0.783203] dma-buf: Running sanitycheck [ 0.787602] dma-buf: Running dma_fence [ 0.791802] sizeof(dma_fence)=48 [ 0.795573] dma-buf: Running dma_fence/sanitycheck [ 0.800958] dma-buf: Running dma_fence/test_signaling [ 0.806646] dma-buf: Running dma_fence/test_add_callback [ 0.812602] dma-buf: Running dma_fence/test_late_add_callback [ 0.819085] dma-buf: Running dma_fence/test_rm_callback [ 0.824958] dma-buf: Running dma_fence/test_late_rm_callback [ 0.831305] dma-buf: Running dma_fence/test_status [ 0.836690] dma-buf: Running dma_fence/test_error [ 0.841965] dma-buf: Running dma_fence/test_wait [ 0.847155] dma-buf: Running dma_fence/test_wait_timeout [ 0.892778] dma-buf: Running dma_fence/test_stub [ 0.897974] dma-buf: Running dma_fence/race_signal_callback [ 0.973013] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.984087] thread_signal_callback[0] completed 37112 passes, 18 misses [ 0.991542] thread_signal_callback[1] completed 37121 passes, 28 misses [ 0.991710] [DISP] disp_device_attached_and_enable,line:233: [ 0.991714] attached ok, mgr0<-->dev0 [ 1.009480] [DISP] disp_device_attached_and_enable,line:236: [ 1.009489] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8 [ 1.072795] thread_signal_callback[0] completed 30849 passes, 30849 misses [ 1.080527] thread_signal_callback[1] completed 30882 passes, 30882 misses [ 1.089021] spi-nand: probe of spi0.0 failed with error -5 [ 1.095234] Error: Driver 'spi-nand' is already registered, aborting... [ 1.102996] libphy: Fixed MDIO Bus: probed [ 1.108085] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.115440] sunxi-ehci: EHCI SUNXI driver [ 1.120296] get ehci0-controller wakeup-source is fail. [ 1.126295] sunxi ehci0-controller don't init wakeup source [ 1.132552] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b65180, 0x:c8830000, irq_no:37 [ 1.144575] [sunxi-ehci0]: Not init ehci0 [ 1.149308] get ehci1-controller wakeup-source is fail. [ 1.155309] sunxi ehci1-controller don't init wakeup source [ 1.161565] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b656a0, 0x:c8834000, irq_no:39 [ 1.173967] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator [ 1.186256] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 1.193629] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 1.203575] sunxi-ehci 4200000.ehci1-controller: irq 57, io mem 0x04200000 [ 1.232788] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 1.241421] hub 1-0:1.0: USB hub found [ 1.245683] hub 1-0:1.0: 1 port detected [ 1.250608] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.257612] sunxi-ohci: OHCI SUNXI driver [ 1.262530] get ohci0-controller wakeup-source is fail. [ 1.268521] sunxi ohci0-controller don't init wakeup source [ 1.274809] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b65410 [ 1.284485] [sunxi-ohci0]: Not init ohci0 [ 1.289219] get ohci1-controller wakeup-source is fail. [ 1.295214] sunxi ohci1-controller don't init wakeup source [ 1.301467] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b65930 [ 1.311368] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator [ 1.323674] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 1.330926] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 1.340869] sunxi-ohci 4200400.ohci1-controller: irq 58, io mem 0x04200400 [ 1.417559] hub 2-0:1.0: USB hub found [ 1.421802] hub 2-0:1.0: 1 port detected [ 1.426863] usbcore: registered new interface driver cdc_acm [ 1.433243] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.442333] usbcore: registered new interface driver usb-storage [ 1.450064] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.460829] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.471909] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.477645] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 1.488302] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:52 UTC (52) [ 1.497313] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 1.503122] i2c /dev entries driver [ 1.507114] sunxi cedar version 1.1 [ 1.511185] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.517549] VE: sunxi_cedar_probe power-domain init!!! [ 1.523334] VE: install start!!! [ 1.523334] [ 1.528835] VE: cedar-ve the get irq is 40 [ 1.528835] [ 1.535322] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval) [ 1.535322] [ 1.544635] VE: install end!!! [ 1.544635] [ 1.549712] VE: sunxi_cedar_probe [ 1.553639] Bluetooth: HCI UART driver ver 2.3 [ 1.558625] Bluetooth: HCI UART protocol H4 registered [ 1.564419] Bluetooth: HCI UART protocol BCSP registered [ 1.570676] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 1.579355] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40) [ 1.589249] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.595467] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.601815] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.608276] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.614735] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.621276] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.627827] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.634379] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.641669] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.652855] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.673002] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.697255] sunxi-mmc 4020000.sdmmc: detmode:gpio polling [ 1.703352] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.715466] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40) [ 1.725361] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 1.726453] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.731577] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 1.749504] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 1.755975] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 1.762435] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 1.762443] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.770272] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.780625] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 1.780631] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 1.805370] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 1.811946] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 1.821328] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.832537] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 1.846591] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.852708] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.867231] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 1.878828] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 1.879833] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 1.897439] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 1.898169] exFAT: Version 1.3.0 [ 1.909179] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 1.909233] mmc0: new high speed SDHC card at address 0001 [ 1.913335] usbcore: registered new interface driver snd-usb-audio [ 1.919665] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 1.920567] mmcblk0: mmc0:0001 SD 29.1 GiB [ 1.925920] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.936829] NET: Registered protocol family 10 [ 1.942812] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.945474] Segment Routing with IPv6 [ 1.958307] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 1.961275] NET: Registered protocol family 17 [ 1.973539] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 1.976811] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 1.983723] Bluetooth: RFCOMM TTY layer initialized [ 1.988473] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.012405] Bluetooth: RFCOMM socket layer initialized [ 2.018189] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.024979] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.032806] Bluetooth: RFCOMM ver 1.11 [ 2.040869] Registering SWP/SWPB emulation handler [ 2.060233] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 2.071667] sunxi-i2c sunxi-i2c0: sunxi-i2c0 supply twi not found, using dummy regulator [ 2.081492] sunxi-i2c sunxi-i2c0: probe success [ 2.087036] sunxi-i2c sunxi-i2c1: sunxi-i2c1 supply twi not found, using dummy regulator [ 2.096801] sunxi-i2c sunxi-i2c1: probe success [ 2.103869] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator [ 2.117290] clk: Not disabling unused clocks [ 2.122091] ALSA device list: [ 2.125612] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.135323] No soundcards found. [ 2.135336] alloc_fd: slot 0 not NULL! [ 2.143402] cfg80211: failed to load regulatory.db [ 2.152749] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.163145] devtmpfs: mounted [ 2.168378] Freeing unused kernel memory: 1024K [ 2.192919] Run /pseudo_init as init process mount: mounting none on /dev failed: Resource busy mount: mounting /dev/by-name/rootfs_data on /overlay failed: Invalid argument Mount Failed: formating /dev/by-name/rootfs_data to ext4 ... /pseudo_init: line 403: mkfs.ext4: not found can't run '/etc/preinit': No such file or directory mount: mounting proc on /proc failed: Resource busy mount: mounting tmpfs on /run failed: No such file or directory hostname: can't open '/etc/hostname': No such file or directory ------run rc.preboot file----- /etc/init.d/rcS: line 152: mkfs.ext4: not found ------run rc.modules file----- ------run rc.final file----- amixer: Control default open error: No such device BusyBox v1.27.2 () built-in shell (ash) ------run profile file----- _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 61CC0487) [ 2.570615] file system registered ---------------------------------------------- Mon Feb 6 00:00:00 GMT 2023 nodev debugfs root@TinaLinux:/# [ 2.590966] configfs-gadget 4100000.udc-controller: failed to start g1: -19 sh: write error: No such device [ 2.821556] random: fast init done [ 3.653053] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator [ 3.669176] read descriptors [ 3.672423] read strings [ 3.916342] android_work: sent uevent USB_STATE=CONNECTED [ 4.024823] configfs-gadget gadget: high-speed config #1: c [ 4.031158] android_work: sent uevent USB_STATE=CONFIGURED [ 5.972815] android_work: sent uevent USB_STATE=DISCONNECTED [ 6.044754] android_work: sent uevent USB_STATE=CONNECTED [ 6.152186] configfs-gadget gadget: high-speed config #1: c [ 6.158511] android_work: sent uevent USB_STATE=CONFIGURED [ 15.532811] android_work: sent uevent USB_STATE=DISCONNECTED [ 15.608515] android_work: sent uevent USB_STATE=CONNECTED [ 15.717205] configfs-gadget gadget: high-speed config #1: c [ 15.723521] android_work: sent uevent USB_STATE=CONFIGURED [ 30.902823] android_work: sent uevent USB_STATE=DISCONNECTED [ 30.977845] android_work: sent uevent USB_STATE=CONNECTED [ 31.086930] configfs-gadget gadget: high-speed config #1: c [ 31.093253] android_work: sent uevent USB_STATE=CONFIGURED
-
大佬 膜拜!!!!!!!!!
-
屏幕已经ok了, 主要是背光电阻坏了,测了LED驱动FB电压排查到了,而且4对lanes,其中有损坏的主要是虚焊了,进行BIST测试看出来的,目前触摸还在调整。设备树、驱动也有修改
-
MIPI的原理图 NC接地了,不知道是否是这个引起的排线 发烫,ADB与串口中断,是启动有问题了才导致的。
-
@nathanliu 在 T113-s3 MIPI适配无法点亮 中说:
屏幕已经ok了, 主要是背光电阻坏了,测了LED驱动FB电压排查到了,而且4对lanes,其中有损坏的主要是虚焊了,进行BIST测试看出来的,目前触摸还在调整。设备树、驱动也有修改
bist是指自测是吧。屏幕如何进入自检模式~~求指导
Copyright © 2023 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号