D1 Tina linux 如何修改console打印串口?
-
本人发现在D1 tina linux在启动 boot阶段和kernel段,打印串口默认都是用uart0,TX :PB08 RX:PB09,而且在要修改boot阶段的串口输出在目录device\config\chips\d1\configs\nezha\sys_config.fex.中修改参数:
uart_debug_port = 0 uart_debug_tx = port:PB08<6><1><default><default> uart_debug_rx = port:PB09<6><1><default><default>
即可。但是如何修改console的串口配置?比如console现在默认是用uart0 PB08 PB09,我如何改为用uart2的PC0 PC1?
-
以哪吒为例,
还需要修改以下文件:
device/config/chips/d1/configs/nezha/board.dts
device/config/chips/d1/configs/nezha/uboot-board.dts
device/config/chips/d1/configs/nezha/env.cfg
-
@whycan 我也哪吒开发板,有具体修改文件里面的那里吗?
-
@wadedeng
env.cfg 修改 console参数
dts修改uart2 PC0 PC1 -
@whycan 现在修改了boot0段和kernel段的串口输出。请问uboot段的串口输在哪里修改配置。
-
@wadedeng
看了一下 uboot-board.dts 没有关于 uart 和 console的配置,应该都是在 sys_config.fex 配的,按理如果boot0 正常的话,u-boot也正常了,如果不确定就贴出所有的log看看。 -
[53]HELLO! BOOT0 is starting! [56]BOOT0 commit : 553a5eb [58]set pll start [60]periph0 has been enabled [63]set pll end [64][pmu]: bus read error [67]board init ok [69]ZQ value = 0x2f [70]get_pmu_exist() = -1 [73]DRAM BOOT DRIVE INFO: V0.32 [76]DRAM CLK = 408 MHz [78]DRAM Type = 2 (2:DDR2,3:DDR3) [81]DRAMC read ODT off. [83]DRAM ODT off. [85]ddr_efuse_type: 0xa [87]mark_id: 0x74 [89]DRAM SIZE =64 M [91]PLL_DDR_CTRL_REG:0xf9002100 [94]DRAM_CLK_REG:0xc0000000 [97][TIMING DEBUG] MR2= 0x0 [101]DRAM simple test OK. [104]dram size =64 [106]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32 [111]block from 8 to 32 [184]Check is correct. [186]dma 0x302e8 int is not used yet [189]dma 0x302e8 int is free, you do not need to free it again [195]Entry_name = opensbi [198]Entry_name = u-boot [202]Entry_name = dtb [204]Jump to second Boot. OpenSBI auto-t113-linux-V0.1-1-ge15c4f7 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : T-HEAD Xuantie Platform Platform HART Features : RV64ACDFIMSUVX Platform Max HARTs : 1 Current Hart : 0 Firmware Base : 0x41fc0400 Firmware Size : 75 KB Runtime SBI Version : 0.2 MIDELEG : 0x0000000000000222 MEDELEG : 0x000000000000b1ff PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A) PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X) PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X) PMP3 : 0x0000000000020000-0x0000000000027fff (A,R,W,X) PMP4 : 0x0000000000000000-0x000000003fffffff (A,R,W) ** 586 printk messages dropped ** [DISP] disp_get_layer,line:104: 0,1,0, name=mgr0 chn1 lyr0 [DISP] disp_lyr_save_and_dirty_check,line:529: layer:ch1, layer0, format=0, size=<800,480>, crop=<0,0,800,480>,frame=<800,480>, en=1 addr[0xffe00000,0x0,0x0> [DISP] disp_mgr_apply,line:2480: mgr 0 apply [DISP] bsp_disp_shadow_protect,line:684: sel=0, protect:1, cnt=1 [DISP] de_al_lyr_apply,line:485: ch0 z 0 dis [DISP] de_al_lyr_apply,line:485: ch1 z 0 en [DISP] de_al_lyr_apply,line:488: pipe0 z 1 en [DISP] de_al_lyr_apply,line:488: pipe1 z 0 dis [DISP] de_al_lyr_apply,line:503: format[0]=0 [DISP] de_calc_overlay_scaler_para,line:178: ovl_rect[0]=<0,0> [DISP] de_calc_overlay_scaler_para,line:180: bld_rect[0]=<0,0,0,0> [DISP] de_calc_ovl_coord,line:389: half_shift_xy=<20000,18,0> [DISP] de_calc_ovl_coord,line:389: half_shift_xy=<20000,18,0> [DISP] de_rtmx_calc_chnrect,line:1982: layernum=4, i=0 [DISP] de_rtmx_calc_chnrect,line:1984: crop=<0,0,800,480> [DISP] de_rtmx_calc_chnrect,line:1986: layer=<0,0,800,480> [DISP] de_rtmx_calc_chnrect,line:1995: ovl_rect=<0,0,800,480> [DISP] de_rtmx_calc_chnrect,line:1997: bld_rect=<0,0,800,480> [DISP] de_calc_overlay_scaler_para,line:178: ovl_rect[1]=<800,480> [DISP] de_calc_overlay_scaler_para,line:180: bld_rect[1]=<0,0,800,480> [DISP] de_calc_overlay_scaler_para,line:187: fmt[0]=0, ovlw[0]=0,ovlh[0]=0, bld_rect[0].w=0, bld_rect[0].h=0 [DISP] de_vsu_set_para,line:274: sel0, ch 0, en=0, in<0x0>,out<0x0> [DISP] de_al_lyr_apply,line:713: sel=0, pipe_rect[0]=<0,0,800,480> [DISP] de_rtmx_set_route,line:1792: sel0, pno0, zorder1, route:0x0 [DISP] de_rtmx_set_route,line:1796: addr=0x(____ptrval____), reg=0x1 [DISP] de_al_lyr_apply,line:713: sel=0, pipe_rect[1]=<0,0,0,0> [DISP] de_rtmx_set_route,line:1792: sel0, pno1, zorder0, route:0x1 [DISP] de_rtmx_set_route,line:1796: addr=0x(____ptrval____), reg=0x1 [DISP] bsp_disp_shadow_protect,line:684: sel=0, protect:0, cnt=0 [DISP] disp_mgr_sw_enable,line:2682: mgr 0 enable [DISP] disp_mgr_clk_enable,line:1051: set DE rate to 300000000 [DISP] disp_mgr_clk_enable,line:1067: mgr 0 clk enable [DISP] disp_mgr_sw_enable,line:2730: output res: 800 x 480, cs=0, range=1, interlace=0 [DISP] disp_mgr_apply,line:2480: mgr 0 apply [DISP] bsp_disp_shadow_protect,line:684: sel=0, protect:1, cnt=1 disp_al_manager_apply ouput_type:1 [DISP] de_dcsc_apply,line:74: sel=0, in_fmt=0, mode=0, out_fmt=0, mode=0, range=1 [DISP] de_al_lyr_apply,line:485: ch0 z 0 dis [DISP] de_al_lyr_apply,line:485: ch1 z 0 en [DISP] de_al_lyr_apply,line:488: pipe0 z 1 en [DISP] de_al_lyr_apply,line:488: pipe1 z 0 dis [DISP] de_al_lyr_apply,line:503: format[0]=0 [DISP] de_calc_overlay_scaler_para,line:178: ovl_rect[0]=<0,0> [DISP] de_calc_overlay_scaler_para,line:180: bld_rect[0]=<0,0,0,0> [DISP] de_calc_ovl_coord,line:389: half_shift_xy=<20000,18,0> [DISP] de_calc_ovl_coord,line:389: half_shift_xy=<20000,18,0> [DISP] de_rtmx_calc_chnrect,line:1982: layernum=4, i=0 [DISP] de_rtmx_calc_chnrect,line:1984: crop=<0,0,800,480> [DISP] de_rtmx_calc_chnrect,line:1986: layer=<0,0,800,480> [DISP] de_rtmx_calc_chnrect,line:1995: ovl_rect=<0,0,800,480> [DISP] de_rtmx_calc_chnrect,line:1997: bld_rect=<0,0,800,480> [DISP] de_calc_overlay_scaler_para,line:178: ovl_rect[1]=<800,480> [DISP] de_calc_overlay_scaler_para,line:180: bld_rect[1]=<0,0,800,480> [DISP] de_calc_overlay_scaler_para,line:187: fmt[0]=0, ovlw[0]=0,ovlh[0]=0, bld_rect[0].w=0, bld_rect[0].h=0 [DISP] de_vsu_set_para,line:274: sel0, ch 0, en=0, in<0x0>,out<0x0> [DISP] de_al_lyr_apply,line:713: sel=0, pipe_rect[0]=<0,0,800,480> [DISP] de_rtmx_set_route,line:1792: sel0, pno0, zorder1, route:0x0 [DISP] de_rtmx_set_route,line:1796: addr=0x(____ptrval____), reg=0x1 [DISP] de_al_lyr_apply,line:713: sel=0, pipe_rect[1]=<0,0,0,0> [DISP] de_rtmx_set_route,line:1792: sel0, pno1, zorder0, route:0x1 [DISP] de_rtmx_set_route,line:1796: addr=0x(____ptrval____), reg=0x1 [DISP] bsp_disp_shadow_protect,line:684: sel=0, protect:0, cnt=0 [DISP] lcd_clk_config,line:731: disp 0, clk: pll(198000000),clk(198000000),dclk(33000000) dsi_rate(198000000) clk real:pll(288000000),clk(288000000),dclk(48000000) dsi_rate(0) [DISP] cal_real_frame_period,line:646: lcd frame period:10150000 [DISP] disp_sys_pwm_set_polarity,line:536: disp_sys_pwm_Set_Polarity pwm 5, active low [DISP] disp_sys_pwm_enable,line:479: disp_sys_pwm_Enable pwm 5 [DISP] disp_sys_register_irq,line:113: disp_sys_register_irq, irqNo=30, Handler=0x(____ptrval____), pArg=0x(____ptrval____) [DISP] disp_init,line:2384: disp_init finish [DISP] disp_probe,line:3059: [DISP]disp_probe finish [DISP]disp_module_init finish sunxi_sid_init()551 - insmod ok pwm-regulator: supplied by regulator-dummy uart uart0: get regulator failed uart uart0: uart0 supply uart not found, using dummy regulator uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator uart uart3: get regulator failed uart uart3: uart3 supply uart not found, using dummy regulator uart3: ttyS3 at MMIO 0x2500c00 (irq = 21, base_baud = 1500000) is a SUNXI sw_console_setup()1784 - console setup baud 115200 parity n bits 8, flow n printk: console [ttyS3] enabled sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator uart uart4: get regulator failed uart uart4: uart4 supply uart not found, using dummy regulator uart4: ttyS4 at MMIO 0x2501000 (irq = 22, base_baud = 1500000) is a SUNXI misc dump reg init sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=131 assert=1 sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ADDR_MGT] addr_mgt_probe: module version: v1.0.10 [ADDR_MGT] addr_mgt_probe: success. sunxi-spinand: AW SPINand MTD Layer Version: 2.0 20201228 sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306 sunxi-spinand-phy: not detect any munufacture from id table sunxi-spinand-phy: get spi-nand Model from fdt fail sunxi-spinand-phy: get phy info from fdt fail sunxi-spinand-phy: not detect munufacture from fdt sunxi-spinand-phy: detect munufacture from id table: Micron sunxi-spinand-phy: detect spinand id: ffff242c ffffffff sunxi-spinand-phy: ========== arch info ========== sunxi-spinand-phy: Model: MT29F2G01ABAGDWB sunxi-spinand-phy: Munufacture: Micron sunxi-spinand-phy: DieCntPerChip: 1 sunxi-spinand-phy: BlkCntPerDie: 2048 sunxi-spinand-phy: PageCntPerBlk: 64 sunxi-spinand-phy: SectCntPerPage: 4 sunxi-spinand-phy: OobSizePerPage: 64 sunxi-spinand-phy: BadBlockFlag: 0x0 sunxi-spinand-phy: OperationOpt: 0x8f sunxi-spinand-phy: MaxEraseTimes: 65000 sunxi-spinand-phy: EccFlag: 0x0 sunxi-spinand-phy: EccType: 6 sunxi-spinand-phy: EccProtectedType: 5 sunxi-spinand-phy: ======================================== sunxi-spinand-phy: sunxi-spinand-phy: ========== physical info ========== sunxi-spinand-phy: TotalSize: 256 M sunxi-spinand-phy: SectorSize: 512 B sunxi-spinand-phy: PageSize: 2 K sunxi-spinand-phy: BlockSize: 128 K sunxi-spinand-phy: OOBSize: 64 B sunxi-spinand-phy: ======================================== sunxi-spinand-phy: sunxi-spinand-phy: ========== logical info ========== sunxi-spinand-phy: TotalSize: 256 M sunxi-spinand-phy: SectorSize: 512 B sunxi-spinand-phy: PageSize: 4 K sunxi-spinand-phy: BlockSize: 256 K sunxi-spinand-phy: OOBSize: 128 B sunxi-spinand-phy: ======================================== sunxi-spinand-phy: MT29F2G01ABAGDWB reset rx bit width to 1 sunxi-spinand-phy: MT29F2G01ABAGDWB reset tx bit width to 1 sunxi-spinand-phy: block lock register: 0x00 sunxi-spinand-phy: feature register: 0x10 sunxi-spinand-phy: sunxi physic nand init end Creating 4 MTD partitions on "sunxi_mtd_nand": 0x000000000000-0x000000100000 : "boot0" 0x000000100000-0x000000500000 : "uboot" random: fast init done 0x000000500000-0x000000600000 : "secure_storage" 0x000000600000-0x000010000000 : "sys" sunxi-spinand-phy: phy blk 387 is bad sunxi-spinand-phy: phy blk 777 is bad random: crng init done sunxi-spinand-phy: phy blk 1962 is bad ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver sunxi-ehci: EHCI SUNXI driver get ehci1-controller wakeup-source is fail. sunxi ehci1-controller don't init wakeup source [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0005c9628, 0x:ffffffd004073000, irq_no:31 sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver sunxi-ohci: OHCI SUNXI driver get ohci1-controller wakeup-source is fail. sunxi ohci1-controller don't init wakeup source [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0005c99f0 sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver uas usbcore: registered new interface driver usb-storage sunxi_gpadc_init,2137, success sunxi_gpadc_setup: get channel scan data failed input: sunxi-gpadc0 as /devices/virtual/input/input0 i2c /dev entries driver IR NEC protocol handler initialized sunxi cedar version 1.1 sunxi-cedar 1c0e000.ve: Adding to iommu group 0 VE: install start!!! VE: cedar-ve the get irq is 6 VE: install end!!! VE: sunxi_cedar_probe sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.21 2021-05-24 16:10) sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 sunxi-mmc 4021000.sdmmc: No vmmc regulator found sunxi-mmc 4021000.sdmmc: No vqmmc regulator found sunxi-mmc 4021000.sdmmc: No vdmmc regulator found sunxi-mmc 4021000.sdmmc: No vd33sw regulator found sunxi-mmc 4021000.sdmmc: No vd18sw regulator found sunxi-mmc 4021000.sdmmc: No vq33sw regulator found sunxi-mmc 4021000.sdmmc: No vq18sw regulator found sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: detmode:manually by software sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! ashmem: initialized sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B exFAT: Version 1.3.0 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [AUDIOCODEC][sunxi_codec_parse_params][2412]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [AUDIOCODEC][sunxi_codec_parse_params][2448]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sid_rd_ver_reg()254 - ver >= 4, soc ver:5 sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [SNDCODEC][sunxi_card_init][583]:card init finished sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [SNDCODEC][sunxi_card_dev_probe][836]:register card finished NET: Registered protocol family 10 Segment Routing with IPv6 NET: Registered protocol family 17 [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch i2c i2c2: i2c2 supply twi not found, using dummy regulator i2c i2c2: probe success get ehci0-controller wakeup-source is fail. sunxi ehci0-controller don't init wakeup source [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0005c8e98, 0x:ffffffd0040e6000, irq_no:2e [sunxi-ehci0]: Not init ehci0 get ohci0-controller wakeup-source is fail. sunxi ohci0-controller don't init wakeup source [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0005c9260 [sunxi-ohci0]: Not init ohci0 ubi0: attaching mtd3 ubi0: scanning is finished ubi0: attached mtd3 (name "sys", size 250 MiB) ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 997, bad PEBs: 3, corrupted PEBs: 0 ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 ubi0: available PEBs: 16, total reserved PEBs: 981, PEBs reserved for bad PEB handling: 17 ubi0: background thread "ubi_bgt0d" started, PID 60 block ubiblock0_5: created from ubi0:5(rootfs) platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 clk: Not disabling unused clocks ALSA device list: #0: audiocodec alloc_fd: slot 0 not NULL! cfg80211: failed to load regulatory.db VFS: Mounted root (squashfs filesystem) readonly on device 254:0. devtmpfs: mounted Freeing unused kernel memory: 152K This architecture does not have kernel memory protection. Run /pseudo_init as init process mount: mounting none on /dev failed: Device or resource busy UBIFS (ubi0:6): Mounting in unauthenticated mode UBIFS (ubi0:6): background thread "ubifs_bgt0_6" started, PID 87 UBIFS (ubi0:6): recovery needed UBIFS (ubi0:6): recovery completed UBIFS (ubi0:6): UBIFS: mounted UBI device 0, volume 6, name "rootfs_data" UBIFS (ubi0:6): LEB size: 258048 bytes (252 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes UBIFS (ubi0:6): FS size: 3096576 bytes (2 MiB, 12 LEBs), journal size 1806337 bytes (1 MiB, 5 LEBs) UBIFS (ubi0:6): reserved for root: 146258 bytes (142 KiB) UBIFS (ubi0:6): media format: w5/r0 (latest is w5/r0), UUID 8E54C7FB-113C-4EB2-AE5B-950DE41C9ADE, small LPT model can't run '/etc/preinit': No such file or directory mount: mounting proc on /proc failed: Device or resource busy mount: mounting tmpfs on /run failed: No such file or directory hostname: can't open '/etc/hostname': No such file or directory ------run rc.preboot file----- UBIFS (ubi0:7): Mounting in unauthenticated mode UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 116 UBIFS (ubi0:7): recovery needed UBIFS (ubi0:7): recovery completed UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "UDISK" UBIFS (ubi0:7): LEB size: 258048 bytes (252 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes UBIFS (ubi0:7): FS size: 179601408 bytes (171 MiB, 696 LEBs), journal size 9031680 bytes (8 MiB, 35 LEBs) UBIFS (ubi0:7): reserved for root: 4952683 bytes (4836 KiB) UBIFS (ubi0:7): media format: w5/r0 (latest is w5/r0), UUID CF2A1B34-6910-40D4-BB19-F188E12AE214, small LPT model /etc/init.d/rcS: line 136: can't create /proc/sys/kernel/hotplug: nonexistent directory ------run rc.modules file----- get ctp_power is fail, -22 get ctp_power_ldo_vol is fail, -22 sunxi_ctp_startup: ctp_power_io is invalid. get ctp_gesture_wakeup fail, no gesture wakeup gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. <<-GTP-ERROR->> GTP i2c test failed time 1. i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. insmod_device_driver sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator <<-GTP-ERROR->> GTP i2c test failed time 2. i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. <<-GTP-ERROR->> GTP i2c test failed time 3. i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. <<-GTP-ERROR->> GTP i2c test failed time 4. i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) i2c i2c2: incomplete xfer (status: 0x20, dev addr: 0x14) <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. <<-GTP-ERROR->> GTP i2c test failed time 5. I2C communication ERROR! regulator-dummy: Underflow of regulator enable count gt9xxnew_ts: probe of 2-0014 failed with error -1 Error: Driver 'gt9xxnew_ts' is already registered, aborting... insmod: can't insert '/lib/modules/5.4.61/gt9xxnew_ts.ko': Operation not permitted ======== XRADIO WIFI OPEN ======== [XRADIO_ERR] debugfs isnot initialized [XRADIO] Driver Label:XR_V02.25.82 Dec 15 2021 07:06:51 [XRADIO] Allocated hw_priv @ 000000009eacf2e2 sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [XRADIO] Detect SDIO card 1 sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [XRADIO] Remove SDIO card 1 [SBUS_ERR] sdio probe timeout! sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [XRADIO_ERR] sbus_sdio_init failed xradio_core_init failed (-110)! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B ======== XRADIO WIFI OPEN ======== [XRADIO_ERR] debugfs isnot initialized [XRADIO] Driver Label:XR_V02.25.82 Dec 15 2021 07:06:51 [XRADIO] Allocated hw_priv @ 0000000056985b32 sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [XRADIO] Detect SDIO card 1 sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [XRADIO] Remove SDIO card 1 [SBUS_ERR] sdio probe timeout! sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [XRADIO_ERR] sbus_sdio_init failed xradio_core_init failed (-110)! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 0 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B insmod: can't insert '/lib/modules/5.4.61/xr819s.ko': Connection timed out Successfully initialized wpa_supplicant Could not read interface wlan0 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Could not read interface wlan0 flags: No such device wlan0: Failed to initialize driver interface ------run rc.final file----- numid=30,iface=MIXER,name='Headphone Switch' ; type=BOOLEAN,access=rw------,values=1 : values=on file system registered configfs-gadget 4100000.udc-controller: failed to start g1: -19 sh: write error: No such device /etc/rc.common: line 128: tr: not found read descriptors read strings sunxi_set_cur_vol_work()397 WARN: get power supply failed android_work: sent uevent USB_STATE=CONNECTED sunxi_set_cur_vol_work()397 WARN: get power supply failed configfs-gadget gadget: high-speed config #1: c android_work: sent uevent USB_STATE=CONFIGURED rmmod_device_driver rmmod_device_driver()222 WARN: get power supply failed android_work: sent uevent USB_STATE=DISCONNECTED insmod_host_driver [ehci0-controller]: sunxi_usb_enable_ehci [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0005c8e98, 0x:ffffffd0040e6000, irq_no:2e sunxi-ehci 4101000.ehci0-controller: 4101000.ehci0-controller supply hci not found, using dummy regulator sunxi-ehci 4101000.ehci0-controller: EHCI Host Controller sunxi-ehci 4101000.ehci0-controller: new USB bus registered, assigned bus number 3 sunxi-ehci 4101000.ehci0-controller: irq 46, io mem 0x04101000 sunxi-ehci 4101000.ehci0-controller: USB 2.0 started, EHCI 1.00 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected [ohci0-controller]: sunxi_usb_enable_ohci [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0005c9260 sunxi-ohci 4101400.ohci0-controller: 4101400.ohci0-controller supply hci not found, using dummy regulator sunxi-ohci 4101400.ohci0-controller: OHCI Host Controller sunxi-ohci 4101400.ohci0-controller: new USB bus registered, assigned bus number 4 sunxi-ohci 4101400.ohci0-controller: irq 47, io mem 0x04101400 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected host_chose finished! BusyBox v1.27.2 () built-in shell (ash) ------run profile file----- _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 5C1C9C53) ---------------------------------------------- mount: mounting none on /sys/kernel/debug failed: No such file or directory root@TinaLinux:/# INFO : cedarc <log_set_level:43>: Set log level to 3 from /vendor/etc/cedarc.conf DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-0 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-1 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-2 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-3 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-4 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-5 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-6 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-7 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-8 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-9 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-10 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-11 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-12 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry adecoder-13 ok. DEBUG : awplayer <ReadPluginEntry:194>: read plugin entry adecoder-14 fail! DEBUG : awplayer <CdxPluginLoadList:221>: have config 14 entry DEBUG : awplayer <CdxPluginLoadList:222>: start to open adecoder lib DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.aac comment is "aac_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_aacdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.alac comment is "alac_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_alacdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.amr comment is "amr_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_amrdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.ape comment is "ape_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_apedec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.flac comment is "flac_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_flacdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.mp3 comment is "mp3_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_mp3dec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.ogg comment is "ogg_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_oggdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.wav comment is "wav_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_wavdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.atrc comment is "atrc_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_atrcdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.ra comment is "ra_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_radec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.sipr comment is "sipr_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_siprdec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.dsd comment is "dsd_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_dsddec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.g729 comment is "g729_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_g729dec.so DEBUG : awplayer <DlOpenPlugin:96>: plugin adecoder.opus comment is "opus_adecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libaw_opusdec.so DEBUG : awplayer <CdxPluginLoadList:202>: Load Plugin list vdecoder DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-0 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-1 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-2 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-3 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-4 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-5 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-6 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-7 ok. DEBUG : awplayer <ReadPluginEntry:178>: read plugin entry vdecoder-8 ok. DEBUG : awplayer <ReadPluginEntry:194>: read plugin entry vdecoder-9 fail! DEBUG : awplayer <CdxPluginLoadList:221>: have config 9 entry DEBUG : awplayer <CdxPluginLoadList:222>: start to open vdecoder lib DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.h264 comment is "h264_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawh264.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:79>: register h264 decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.mjpeg comment is "mjpeg_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawmjpeg.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:84>: register mjpeg decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.mpeg2 comment is "mpeg2_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawmpeg2.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:86>: register mpeg2 decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.mpeg4base comment is "mpeg4base_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawmpeg4base.so WARNING: awplayer <DlOpenPlugin:112>: Invalid plugin,function CedarPluginVDInit not found. DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.mpeg4dx comment is "mpeg4dx_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawmpeg4dx.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:92>: register mpeg4dx decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.mpeg4h263 comment is "mpeg4h263_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawmpeg4h263.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:79>: register mpeg4H263 decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.mpeg4normal comment is "mpeg4normal_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawmpeg4normal.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:90>: register mpeg4Normal decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.wmv3 comment is "wmv3_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawwmv3.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:74>: register vc1 decoder success! DEBUG : awplayer <DlOpenPlugin:96>: plugin vdecoder.h265 comment is "h265_vdecoder" DEBUG : awplayer <DlOpenPlugin:97>: plugin open lib: libawh265.so DEBUG : awplayer <DlOpenPlugin:116>: plugin init : CedarPluginVDInit INFO : cedarc <CedarPluginVDInit:85>: register h265 decoder success! DEBUG : awplayer <CdxPluginLoadList:202>: Load Plugin list plugin DEBUG : awplayer <ReadPluginEntry:194>: read plugin entry plugin-0 fail! DEBUG : awplayer <CdxPluginLoadList:221>: have config 0 entry DEBUG : awplayer <CdxPluginLoadList:222>: start to open plugin lib DEBUG : awplayer <AwStreamInit:107>: aw stream init... DEBUG : awplayer <AwStreamInit:150>: stream list size:8 INFO : awplayer <AwParserInit:441>: aw parser init... DEBUG : awplayer <AwParserInit:560>: aw parser size:17 DEBUG : awplayer <AwMuxerInit:60>: aw muxer init .. DEBUG : awplayer <AwMuxerInit:74>: aw muxer size:3 info:<main:228>#################### info:<main:229>#################### info:<main:230>#################### info:<main:231>main start V1.0 info:<read_all_param:369>major key:public: info:<read_all_param:375>volume:15 info:<read_all_param:382>language:1 info:<read_all_param:386>major key:music: info:<read_all_param:392>loop:0 info:<read_all_param:400>path: info:<read_all_param:408>filename: info:<read_all_param:415>fileType:0 info:<read_all_param:422>offset:0 info:<read_all_param:429>index:0 info:<read_all_param:436>nDurationMs:0 info:<read_all_param:440>major key:movie: info:<read_all_param:446>loop:0 info:<read_all_param:454>path: info:<read_all_param:462>filename: info:<read_all_param:469>fileType:0 info:<read_all_param:476>offset:0 info:<read_all_param:483>index:0 info:<read_all_param:490>nDurationMs:0 info:<read_all_param:494>major key:ext_music: info:<read_all_param:500>loop:0 info:<read_all_param:508>path: info:<read_all_param:516>filename: info:<read_all_param:523>fileType:0 info:<read_all_param:530>offset:0 info:<read_all_param:537>index:0 info:<read_all_param:544>nDurationMs:0 info:<read_all_param:547>major key:WLAN: info:<read_all_param:553>manu_on:1 info:<read_all_param:560>manu_connected:1 info:<read_all_param:569>manu_ssid:AW-Guest info:<read_all_param:578>manu_password:Aw.guest6688 numid=30,iface=MIXER,name='Headphone Switch' ; type=BOOLEAN,access=rw------,values=1 : values=on amixer: Cannot find the given element from control default The framebuffer device was opened successfully. 800x480, 32bpp The framebuffer device was mapped to memory successfully. unable open evdev interface:: No such file or directory info:<init_text:265>lang=1, dataFile=/usr/res/font/en.bin connect wpa_supplicant failed,please check wifi driver!
-
@whycan 这是开机所有log,唯有uboot那段没有打印,看了uboot-board.dts,里面没有关于console和uart的配置,所有我猜想uboot段的端口输出有可能在u-boot源码配置
-
@wadedeng
这么说也有道理,晚点我试一试。 -
@wadedeng 在uboot中增加下面的修改试试:
diff --git a/configs/sun20iw1p1_defconfig b/configs/sun20iw1p1_defconfig index 98cc435e86..f616e1885c 100644 --- a/configs/sun20iw1p1_defconfig +++ b/configs/sun20iw1p1_defconfig @@ -129,6 +129,9 @@ CONFIG_CMD_PART=y CONFIG_SUNXI_SECURE_BOOT=y CONFIG_SUNXI_ANTI_BRUSH=y +# serial +CONFIG_CONS_INDEX=3 + #COMP #CONFIG_SUNXI_COMP_GZ=y CONFIG_SUNXI_COMP_DETECT=y
如果这个修改不行,那么将 configs/sun20iw1p1_*_defconfig 的文件都统一修改一下。
-
@chengwei_peng 是这个问题,我也是在menuconfig 修改了这个配置 才可以了
-
@wadedeng 请问下具体怎么修改的了?能辛苦下贴出来吗?我放好使用D1 2.1的系统改T113的系统有遇到这个问题,谢谢
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号