Navigation

    全志在线开发者论坛

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • 在线文档
    • 社区主页
    1. Home
    2. Lts52341314
    L
    • Profile
    • Following 0
    • Followers 0
    • my integral 369
    • Topics 2
    • Posts 10
    • Best 0
    • Groups 0

    Lts52341314LV 3

    @Lts52341314

    369
    integral
    0
    Reputation
    1
    Profile views
    10
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Lts52341314 Unfollow Follow

    Latest posts made by Lts52341314

    • Reply: F133烧录失败

      @yuzukitsuru 是硬件问题,刚把未波器表笔调到X10再打到24M OSC_IN居然下载程序成功了

      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru 我把flash的线割断重新飞线,效果好了些,擦除没问题了,但到下一步还是卡住。把电源芯片加热后能稳定一段时间,冷了后还是卡住。

      fes begin commit:977af20-dirty
      [857]set pll start
      [859]fix vccio detect value:0xc0
      [862]periph0 has been enabled
      [865]set pll end
      [867][pmu]: bus read error
      [869]board init ok
      [871]beign to init dram
      [873]ZQ value = 0x2f
      [875]get_pmu_exist() = -1
      [878]ddr_efuse_type: 0xa
      [880]trefi:7.8ms
      [882][AUTO DEBUG] single rank and full DQ!
      [886]ddr_efuse_type: 0xa
      [888]trefi:7.8ms
      [890][AUTO DEBUG] rank 0 row = 13 
      [893][AUTO DEBUG] rank 0 bank = 4 
      [897][AUTO DEBUG] rank 0 page size = 2 KB 
      [900]DRAM BOOT DRIVE INFO: V0.33
      [903]DRAM CLK = 528 MHz
      [906]DRAM Type = 2 (2:DDR2,3:DDR3)
      [909]DRAMC read ODT  off.
      [911]DRAM ODT off.
      [913]ddr_efuse_type: 0xa
      [916]DRAM SIZE =64 M
      [918]dram_tpr4:0x0
      [919]PLL_DDR_CTRL_REG:0xf8002b00
      [922]DRAM_CLK_REG:0xc0000000
      [925][TIMING DEBUG] MR2= 0x0
      [929]DRAM simple test OK.
      [932]init dram ok
      
      
      U-Boot 2018.05-ga81c5b4-dirty (Jul 23 2022 - 13:47:15 +0800) Allwinner Technology
      
      [03.929]DRAM:  64 MiB
      [03.933]Relocation Offset is: 01ef1000
      [03.958]secure enable bit: 0
      [03.964]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
      [03.970]flash init start
      [03.972]workmode = 16,storage type = 0
      try card 2
      set card number 2
      get card number 2
      [03.980][mmc]: mmc driver ver uboot2018:2021-11-04 09:52:00
      [03.989][mmc]: get sdc_type fail and use default host:tm4.
      [04.020][mmc]: Is not Boot mode!
      [04.023][mmc]: SUNXI SDMMC Controller Version:0x50310
      [04.034][mmc]: ************Try SD card 2************
      [04.039][mmc]: mmc 2 cmd timeout 100 status 100
      [04.043][mmc]: smc 2 err, cmd 8,  RTO
      [04.047][mmc]: mmc 2 close bus gating and reset
      [04.052][mmc]: mmc 2 cmd timeout 100 status 100
      [04.056][mmc]: smc 2 err, cmd 55,  RTO
      [04.059][mmc]: mmc 2 close bus gating and reset
      [04.064][mmc]: ************Try MMC card 2************
      [04.073][mmc]: mmc 2 cmd timeout 100 status 100
      [04.077][mmc]: smc 2 err, cmd 1,  RTO
      [04.080][mmc]: mmc 2 close bus gating and reset
      [04.084][mmc]: Card did not respond to voltage select!
      [04.089][mmc]: ************SD/MMC 2 init error!************
      [04.094][mmc]: mmc init product failed
      MMC init failed
      try emmc fail
      [04.110]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407
      [04.116]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306
      [04.177]sunxi-spinand-phy: request spi0 gpio ok
      [04.181]sunxi-spinand-phy: request general tx dma channel ok!
      [04.186]sunxi-spinand-phy: request general rx dma channel ok!
      [04.192]sunxi-spinand-phy: set spic0 clk to 20 Mhz
      [04.196]sunxi-spinand-phy: init spic0 clk ok
      sspi->base_addr = 0x4025000, the SPI control register:
      [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184
      [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020
      [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002
      [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000
      [BCC] 0x4025038 = 0x00000000, [DMA] 0x4025088 = 0x000000e5
      
      [04.242]sunxi-spinand-phy: not detect any munufacture from id table
      [04.257]sunxi-spinand-phy: get spi-nand Model from fdt fail
      [04.262]sunxi-spinand-phy: get phy info from fdt fail
      [04.267]sunxi-spinand-phy: not detect munufacture from fdt
      [04.272]sunxi-spinand-phy: detect munufacture from id table: Mxic
      [04.278]sunxi-spinand-phy: detect spinand id: ffff12c2 ffffffff
      [04.284]sunxi-spinand-phy: ========== arch info ==========
      [04.289]sunxi-spinand-phy: Model:               MX35LF1GE4AB
      [04.294]sunxi-spinand-phy: Munufacture:         Mxic
      [04.299]sunxi-spinand-phy: DieCntPerChip:       1
      [04.303]sunxi-spinand-phy: BlkCntPerDie:        1024
      [04.308]sunxi-spinand-phy: PageCntPerBlk:       64
      [04.313]sunxi-spinand-phy: SectCntPerPage:      4
      [04.317]sunxi-spinand-phy: OobSizePerPage:      64
      [04.322]sunxi-spinand-phy: BadBlockFlag:        0x1
      [04.326]sunxi-spinand-phy: OperationOpt:        0x7
      [04.331]sunxi-spinand-phy: MaxEraseTimes:       65000
      [04.336]sunxi-spinand-phy: EccFlag:             0x2
      [04.340]sunxi-spinand-phy: EccType:             4
      [04.345]sunxi-spinand-phy: EccProtectedType:    3
      [04.349]sunxi-spinand-phy: ========================================
      [04.355]sunxi-spinand-phy: 
      [04.357]sunxi-spinand-phy: ========== physical info ==========
      [04.363]sunxi-spinand-phy: TotalSize:    128 M
      [04.367]sunxi-spinand-phy: SectorSize:   512 B
      [04.371]sunxi-spinand-phy: PageSize:     2 K
      [04.375]sunxi-spinand-phy: BlockSize:    128 K
      [04.379]sunxi-spinand-phy: OOBSize:      64 B
      [04.384]sunxi-spinand-phy: ========================================
      [04.390]sunxi-spinand-phy: 
      [04.392]sunxi-spinand-phy: ========== logical info ==========
      [04.398]sunxi-spinand-phy: TotalSize:    128 M
      [04.402]sunxi-spinand-phy: SectorSize:   512 B
      [04.406]sunxi-spinand-phy: PageSize:     4 K
      [04.410]sunxi-spinand-phy: BlockSize:    256 K
      [04.414]sunxi-spinand-phy: OOBSize:      128 B
      [04.418]sunxi-spinand-phy: ========================================
      [04.434]sunxi-spinand-phy: MX35LF1GE4AB reset rx bit width to 1
      [04.439]sunxi-spinand-phy: MX35LF1GE4AB reset tx bit width to 1
      [04.445]sunxi-spinand-phy: set spic0 clk to 100 Mhz
      [04.449]sunxi-spinand-phy: block lock register: 0x00
      [04.454]sunxi-spinand-phy: feature register: 0x11
      [04.459]sunxi-spinand-phy: sunxi physic nand init end
      [04.468]Loading Environment from SUNXI_FLASH... OK
      [04.481]try to burn key
      [04.485]out of usb burn from boot: not need burn key
      [04.490]Net:   [04.491]No ethernet found.
      Hit any key to stop autoboot:  0 
      sunxi work mode=0x10
      run usb efex
      delay time 2500
      weak:otg_phy_config
      usb init ok
      set address 0x10
      set address 0x10 ok
      set address 0x14
      set address 0x14 ok
      the 0 mbr table is ok
      the 1 mbr table is ok
      the 2 mbr table is ok
      the 3 mbr table is ok
      *************MBR DUMP***************
      total mbr part 8
      
      part[0] name      :boot-resource
      part[0] classname :DISK
      part[0] addrlo    :0x800
      part[0] lenlo     :0x1f8
      part[0] user_type :32768
      part[0] keydata   :0
      part[0] ro        :0
      
      part[1] name      :env
      part[1] classname :DISK
      part[1] addrlo    :0x9f8
      part[1] lenlo     :0x1f8
      part[1] user_type :32768
      part[1] keydata   :0
      part[1] ro        :0
      
      part[2] name      :env-redund
      part[2] classname :DISK
      part[2] addrlo    :0xbf0
      part[2] lenlo     :0x1f8
      part[2] user_type :32768
      part[2] keydata   :0
      part[2] ro        :0
      
      part[3] name      :boot
      part[3] classname :DISK
      part[3] addrlo    :0xde8
      part[3] lenlo     :0x5000
      part[3] user_type :32768
      part[3] keydata   :0
      part[3] ro        :0
      
      part[4] name      :rootfs
      part[4] classname :DISK
      part[4] addrlo    :0x5de8
      part[4] lenlo     :0xe600
      part[4] user_type :32768
      part[4] keydata   :0
      part[4] ro        :0
      
      part[5] name      :recovery
      part[5] classname :DISK
      part[5] addrlo    :0x143e8
      part[5] lenlo     :0x5780
      part[5] user_type :32768
      part[5] keydata   :0
      part[5] ro        :0
      
      part[6] name      :rootfs_data
      part[6] classname :DISK
      part[6] addrlo    :0x19b68
      part[6] lenlo     :0x2800
      part[6] user_type :32768
      part[6] keydata   :0
      part[6] ro        :0
      
      part[7] name      :UDISK
      part[7] classname :DISK
      part[7] addrlo    :0x1c368
      part[7] lenlo     :0x0
      part[7] user_type :0
      part[7] keydata   :0
      part[7] ro        :0
      
      common1(partition3) need it, here is a weak func
      total part: 9
      mbr 0, 800, 8000
      boot-resource 1, 1f8, 8000
      env 2, 1f8, 8000
      env-redund 3, 1f8, 8000
      boot 4, 5000, 8000
      rootfs 5, e600, 8000
      recovery 6, 5780, 8000
      rootfs_data 7, 2800, 8000
      UDISK 8, 0, 0
      [07.696]erase blk 0 to blk 32
      [07.711]blk 20 is bad, skip to erase
      need erase flash: 1
      [07.724]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
      
      device nand0 <nand>, # parts = 4
       #: name                size            offset          mask_flags
       0: boot0               0x00100000      0x00000000      1
       1: uboot               0x00300000      0x00100000      1
       2: secure_storage      0x00100000      0x00400000      1
       3: sys                 0x07b00000      0x00500000      0
      
      active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
      
      defaults:
      mtdids  : nand0=nand
      mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
      [07.784]MTD info (4)
      [07.786]pagesize: 0x1000
      [07.788]blksize: 0x40000
      [07.790]num  offset     bytes      name
      [07.794]0    0x00000000 0x00100000 boot0
      [07.797]1    0x00100000 0x00300000 uboot
      [07.801]2    0x00400000 0x00100000 secure_storage
      [07.805]3    0x00500000 0x07b00000 sys
      [07.809]ubi attach the last part of mtd device: NO.3
      [07.996]ubi0: attaching mtd4
      
      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru SPI nand有办法降频吗

      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru 将Demo板上已经写好的flash芯片焊过来起动一直重复打印这个日志,一直在重启

      [204]HELLO! BOOT0 is starting!
      [207]BOOT0 commit : 977af20-dirty
      [210]set pll start
      [212]fix vccio detect value:0xc0
      [215]periph0 has been enabled
      [218]set pll end
      [220][pmu]: bus read error
      [223]board init ok
      [224]ZQ value = 0x2f
      [226]get_pmu_exist() = -1
      [229]DRAM BOOT DRIVE INFO: V0.33
      [232]DRAM CLK = 528 MHz
      [234]DRAM Type = 2 (2:DDR2,3:DDR3)
      [237]DRAMC read ODT  off.
      [240]DRAM ODT off.
      [242]ddr_efuse_type: 0xa
      [244]DRAM SIZE =64 M
      [246]dram_tpr4:0x0
      [248]PLL_DDR_CTRL_REG:0xf8002b00
      [251]DRAM_CLK_REG:0xc0000000
      [254][TIMING DEBUG] MR2= 0x0
      [258]DRAM simple test OK.
      [261]dram size =64
      [262]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
      [268]block from 8 to 32
      [335]Check is correct.
      [337]dma 0x30338 int is not used yet
      [340]dma 0x30338 int is free, you do not need to free it again
      [345]Entry_name        = opensbi
      [349]Entry_name        = u-boot
      [352]Entry_name        = dtb
      
      U-Boot 2018.05-ga81c5b4-dirty (Jul 23 2022 - 10:43:54 +0800) Allwinner Technology
      
      [00.365]DRAM:  64 MiB
      [00.367]Relocation Offset is: 01ef1000
      [00.371]secure enable bit: 0
      [00.374]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
      [00.380]flash init start
      [00.382]workmode = 0,storage type = 0
      sspi->base_addr = 0x4025000, the SPI control register:
      [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184
      [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020
      [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002
      [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000
      [BCC] 0x4025038 = 0x10000000, [DMA] 0x4025088 = 0x000000e5
      
      [00.430]sunxi-spinand-phy: not detect any munufacture from id table
      [00.436]sunxi-spinand-phy: get spi-nand Model from fdt fail
      [00.442]sunxi-spinand-phy: get phy info from fdt fail
      
      device nand0 <nand>, # parts = 4
       #: name                size            offset          mask_flags
       0: boot0               0x00100000      0x00000000      1
       1: uboot               0x00300000      0x00100000      1
       2: secure_storage      0x00100000      0x00400000      1
       3: sys                 0x07b00000      0x00500000      0
      
      active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
      
      defaults:
      mtdids  : nand0=nand
      mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
      
      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru flash型号能识别

      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru 不清楚什么原因,感觉像突然就停止运行了,flash的线路检查了很多遍和demo没有区别

      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru 也许并不是flash部分的问题

      posted in D1-H/D1s
      L
      Lts52341314
    • Reply: F133烧录失败

      @yuzukitsuru 试了能跳过erase,但还是卡在后续步骤

      [854]fes begin commit:977af20-dirty
      [857]set pll start
      [859]fix vccio detect value:0xc0
      [862]periph0 has been enabled
      [865]set pll end
      [867][pmu]: bus read error
      [869]board init ok
      [871]beign to init dram
      [873]ZQ value = 0x2f
      [875]get_pmu_exist() = -1
      [878]ddr_efuse_type: 0xa
      [880]trefi:7.8ms
      [882][AUTO DEBUG] single rank and full DQ!
      [886]ddr_efuse_type: 0xa
      [888]trefi:7.8ms
      [890][AUTO DEBUG] rank 0 row = 13 
      [893][AUTO DEBUG] rank 0 bank = 4 
      [897][AUTO DEBUG] rank 0 page size = 2 KB 
      [900]DRAM BOOT DRIVE INFO: V0.33
      [903]DRAM CLK = 528 MHz
      [906]DRAM Type = 2 (2:DDR2,3:DDR3)
      [909]DRAMC read ODT  off.
      [911]DRAM ODT off.
      [913]ddr_efuse_type: 0xa
      [916]DRAM SIZE =64 M
      [918]dram_tpr4:0x0
      [919]PLL_DDR_CTRL_REG:0xf8002b00
      [922]DRAM_CLK_REG:0xc0000000
      [925][TIMING DEBUG] MR2= 0x0
      [930]DRAM simple test OK.
      [932]init dram ok
      
      
      U-Boot 2018.05-ga81c5b4-dirty (Jul 23 2022 - 09:11:34 +0800) Allwinner Technology
      
      [03.886]DRAM:  64 MiB
      [03.891]Relocation Offset is: 01ef1000
      [03.916]secure enable bit: 0
      [03.921]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
      [03.928]flash init start
      [03.930]workmode = 16,storage type = 0
      try card 2
      set card number 2
      get card number 2
      [03.938][mmc]: mmc driver ver uboot2018:2021-11-04 09:52:00
      [03.947][mmc]: get sdc_type fail and use default host:tm4.
      [03.978][mmc]: Is not Boot mode!
      [03.981][mmc]: SUNXI SDMMC Controller Version:0x50310
      [03.992][mmc]: ************Try SD card 2************
      [03.997][mmc]: mmc 2 cmd timeout 100 status 100
      [04.001][mmc]: smc 2 err, cmd 8,  RTO
      [04.005][mmc]: mmc 2 close bus gating and reset
      [04.010][mmc]: mmc 2 cmd timeout 100 status 100
      [04.014][mmc]: smc 2 err, cmd 55,  RTO
      [04.017][mmc]: mmc 2 close bus gating and reset
      [04.022][mmc]: ************Try MMC card 2************
      [04.030][mmc]: mmc 2 cmd timeout 100 status 100
      [04.035][mmc]: smc 2 err, cmd 1,  RTO
      [04.038][mmc]: mmc 2 close bus gating and reset
      [04.042][mmc]: Card did not respond to voltage select!
      [04.047][mmc]: ************SD/MMC 2 init error!************
      [04.052][mmc]: mmc init product failed
      MMC init failed
      try emmc fail
      [04.068]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407
      [04.074]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306
      [04.135]sunxi-spinand-phy: request spi0 gpio ok
      [04.139]sunxi-spinand-phy: request general tx dma channel ok!
      [04.144]sunxi-spinand-phy: request general rx dma channel ok!
      [04.150]sunxi-spinand-phy: set spic0 clk to 20 Mhz
      [04.154]sunxi-spinand-phy: init spic0 clk ok
      sspi->base_addr = 0x4025000, the SPI control register:
      [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184
      [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020
      [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002
      [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000
      [BCC] 0x4025038 = 0x00000000, [DMA] 0x4025088 = 0x000000e5
      
      [04.200]sunxi-spinand-phy: not detect any munufacture from id table
      [04.215]sunxi-spinand-phy: get spi-nand Model from fdt fail
      [04.221]sunxi-spinand-phy: get phy info from fdt fail
      [04.225]sunxi-spinand-phy: not detect munufacture from fdt
      [04.231]sunxi-spinand-phy: detect munufacture from id table: Mxic
      [04.236]sunxi-spinand-phy: detect spinand id: ffff12c2 ffffffff
      [04.242]sunxi-spinand-phy: ========== arch info ==========
      [04.247]sunxi-spinand-phy: Model:               MX35LF1GE4AB
      [04.253]sunxi-spinand-phy: Munufacture:         Mxic
      [04.257]sunxi-spinand-phy: DieCntPerChip:       1
      [04.262]sunxi-spinand-phy: BlkCntPerDie:        1024
      [04.266]sunxi-spinand-phy: PageCntPerBlk:       64
      [04.271]sunxi-spinand-phy: SectCntPerPage:      4
      [04.275]sunxi-spinand-phy: OobSizePerPage:      64
      [04.280]sunxi-spinand-phy: BadBlockFlag:        0x1
      [04.284]sunxi-spinand-phy: OperationOpt:        0x7
      [04.289]sunxi-spinand-phy: MaxEraseTimes:       65000
      [04.294]sunxi-spinand-phy: EccFlag:             0x2
      [04.298]sunxi-spinand-phy: EccType:             4
      [04.303]sunxi-spinand-phy: EccProtectedType:    3
      [04.307]sunxi-spinand-phy: ========================================
      [04.313]sunxi-spinand-phy: 
      [04.316]sunxi-spinand-phy: ========== physical info ==========
      [04.321]sunxi-spinand-phy: TotalSize:    128 M
      [04.325]sunxi-spinand-phy: SectorSize:   512 B
      [04.329]sunxi-spinand-phy: PageSize:     2 K
      [04.333]sunxi-spinand-phy: BlockSize:    128 K
      [04.338]sunxi-spinand-phy: OOBSize:      64 B
      [04.342]sunxi-spinand-phy: ========================================
      [04.348]sunxi-spinand-phy: 
      [04.350]sunxi-spinand-phy: ========== logical info ==========
      [04.356]sunxi-spinand-phy: TotalSize:    128 M
      [04.360]sunxi-spinand-phy: SectorSize:   512 B
      [04.364]sunxi-spinand-phy: PageSize:     4 K
      [04.368]sunxi-spinand-phy: BlockSize:    256 K
      [04.372]sunxi-spinand-phy: OOBSize:      128 B
      [04.376]sunxi-spinand-phy: ========================================
      [04.392]sunxi-spinand-phy: MX35LF1GE4AB reset rx bit width to 1
      [04.397]sunxi-spinand-phy: MX35LF1GE4AB reset tx bit width to 1
      [04.403]sunxi-spinand-phy: set spic0 clk to 100 Mhz
      [04.408]sunxi-spinand-phy: block lock register: 0x00
      [04.412]sunxi-spinand-phy: feature register: 0x11
      [04.417]sunxi-spinand-phy: sunxi physic nand init end
      [04.427]Loading Environment from SUNXI_FLASH... OK
      [04.440]try to burn key
      [04.443]out of usb burn from boot: not need burn key
      [04.448]Net:   [04.449]No ethernet found.
      Hit any key to stop autoboot:  0 
      sunxi work mode=0x10
      run usb efex
      delay time 2500
      weak:otg_phy_config
      usb init ok
      set address 0xf
      set address 0xf ok
      set address 0x12
      set address 0x12 ok
      the 0 mbr table is ok
      the 1 mbr table is ok
      the 2 mbr table is ok
      the 3 mbr table is ok
      *************MBR DUMP***************
      total mbr part 8
      
      part[0] name      :boot-resource
      part[0] classname :DISK
      part[0] addrlo    :0x800
      part[0] lenlo     :0x1f8
      part[0] user_type :32768
      part[0] keydata   :0
      part[0] ro        :0
      
      part[1] name      :env
      part[1] classname :DISK
      part[1] addrlo    :0x9f8
      part[1] lenlo     :0x1f8
      part[1] user_type :32768
      part[1] keydata   :0
      part[1] ro        :0
      
      part[2] name      :env-redund
      part[2] classname :DISK
      part[2] addrlo    :0xbf0
      part[2] lenlo     :0x1f8
      part[2] user_type :32768
      part[2] keydata   :0
      part[2] ro        :0
      
      part[3] name      :boot
      part[3] classname :DISK
      part[3] addrlo    :0xde8
      part[3] lenlo     :0x5000
      part[3] user_type :32768
      part[3] keydata   :0
      part[3] ro        :0
      
      part[4] name      :rootfs
      part[4] classname :DISK
      part[4] addrlo    :0x5de8
      part[4] lenlo     :0xe600
      part[4] user_type :32768
      part[4] keydata   :0
      part[4] ro        :0
      
      part[5] name      :recovery
      part[5] classname :DISK
      part[5] addrlo    :0x143e8
      part[5] lenlo     :0x5780
      part[5] user_type :32768
      part[5] keydata   :0
      part[5] ro        :0
      
      part[6] name      :rootfs_data
      part[6] classname :DISK
      part[6] addrlo    :0x19b68
      part[6] lenlo     :0x2800
      part[6] user_type :32768
      part[6] keydata   :0
      part[6] ro        :0
      
      part[7] name      :UDISK
      part[7] classname :DISK
      part[7] addrlo    :0x1c368
      part[7] lenlo     :0x0
      part[7] user_type :0
      part[7] keydata   :0
      part[7] ro        :0
      
      common1(partition3) need it, here is a weak func
      total part: 9
      mbr 0, 800, 8000
      boot-resource 1, 1f8, 8000
      env 2, 1f8, 8000
      env-redund 3, 1f8, 8000
      boot 4, 5000, 8000
      rootfs 5, e600, 8000
      recovery 6, 5780, 8000
      rootfs_data 7, 2800, 8000
      UDISK 8, 0, 0
      need erase flash: 1
      [07.669]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
      
      device nand0 <nand>, # parts = 4
       #: name                size            offset          mask_flags
       0: boot0               0x00100000      0x00000000      1
       1: uboot               0x00300000      0x00100000      1
       2: secure_storage      0x00100000      0x00400000      1
       3: sys                 0x07b00000      0x00500000      0
      
      active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
      
      defaults:
      mtdids  : nand0=nand
      mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
      [07.729]MTD info (4)
      [07.731]pagesize: 0x1000
      [07.733]blksize: 0x40000
      [07.735]num  offset     bytes      name
      [07.739]0    0x00000000 0x00100000 boot0
      [07.743]1    0x00100000 0x00300000 uboot
      [07.746]2    0x00400000 0x00100000 secure_storage
      [07.751]3    0x00500000 0x07b00000 sys
      [07.754]ubi attach the last part of mtd device: NO.3
      
      
      posted in D1-H/D1s
      L
      Lts52341314
    • F133烧录失败

      自已做的F133板子竟然全部不能烧录程序,日志每次都停在这个位置f133_download_.txt ,有没人大神遇到过

      posted in D1-H/D1s
      L
      Lts52341314