大佬们，有哪位点RGB屏遇到过这个现象的
使用echo 8 > /sys/class/disp/disp/attr/colorbar有显示，在视频后面
Z
zhoutian 发布的帖子
-
A133 Android10.0 非安全固件启动慢发布在 其它全志芯片讨论区
大佬们好，我这边编译分安全固件，刷入后发现从上电到进入Launcher接近2分钟左右，另一块刷了安全固件的板子只需要40秒左右，麻烦帮忙看下是为什么
看log能明显看到以下时间有很长的跨越
01-01 08:00:12.710 1783 1783 I vold : Keymaster HAL #1: SoftwareKeymasterDevice from Google SecurityLevel: SOFTWARE HAL: android.hardware.keymaster@4.0::IKeymasterDevice/default
01-01 08:01:21.870 1783 1783 D vold : Computing HMAC with params { (seed: , nonce: aa3d5cfc7dd921cfd361d8584fcc06e235dcc1da0cbf7a54075b4804c8db1a0) }实在是没找到原因，麻烦帮忙看下
-
回复: A133 动态控制debug串口发布在 其它全志芯片讨论区
@whycan 您好，现在代码上串口0是做console，debug串口，但是，我想的有没有办法可以在代码中实现，用个标志位判断，将串口0用做console，或者是用做普通的串口
-
A133 Android10.0 调试GC2145 MIPI CSI发布在 其它全志芯片讨论区
大家好，有哪位大神在a133上调试过gc2145 mipi csi摄像头的，能否指导一下，现在我这边使用的是源码自带的驱动，有检测到sensor，但是不出图
-
A133 android10.0 红外接收上报没有改变发布在 A Series
大家好，请问大家有在调试红外时，上报异常的吗？
已经在rc-sunxi-keymaps.c中static struct rc_map_table sunxi_nec_scan[]添加映射，感觉没有效果
ceres-c3:/ # getevent add device 1: /dev/input/event1 name: "sunxi-keyboard" add device 2: /dev/input/event0 name: "pwr_key" add device 3: /dev/input/event3 name: "sunxi-ir" add device 4: /dev/input/event2 name: "axp803-pek" add device 5: /dev/input/event4 name: "sun50iw10-codec sunxi Audio Jack" /dev/input/event3: 0014 0000 00000000 /dev/input/event3: 0014 0001 00000000 /dev/input/event3: 0004 0004 00ff0009 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0011 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0004 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0009 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0006 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0004 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0011 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0009 /dev/input/event3: 0000 0000 00000000 /dev/input/event3: 0004 0004 00ff0004 /dev/input/event3: 0000 0000 00000000 -
回复: A133 android10.0 lvds显示异常发布在 其它全志芯片讨论区
@whycan
这两个测试过了，有反应，但是，还是会有这个暗
lcd_lvds_colordepth = <0>;
lcd_lvds_mode = <1>; -
A133 android10.0 lvds显示异常发布在 其它全志芯片讨论区
大家有遇到过这种情况吗？点的是双8lvds屏，看颜色应该是正常的，但是有一层灰，正常的颜色见图片
disp: disp@06000000 { disp_init_enable = <1>; disp_mode = <0>; screen0_output_type = <1>; screen0_output_mode = <10>; fb0_format = <9>; fb0_width = <1920>; fb0_height = <1080>; screen1_output_type = <1>; screen1_output_mode = <10>; fb1_format = <9>; fb1_width = <1920>; fb1_height = <1080>; def_output_dev = <0>; hdmi_mode_check = <1>; chn_cfg_mode = <2>; disp_para_zone = <1>; /*VCC-LCD*/ dc1sw-supply = <®_eldo1>; /*VCC-PD*/ dcdc1-supply = <®_dcdc1>; };lcd0: lcd0@01c0c000 { lcd_used = <1>; lcd_driver_name = "default_lcd"; lcd_if = <3>; lcd_x = <1920>; lcd_y = <1080>; lcd_dclk_freq = <150>; lcd_ht = <2210>; lcd_hbp = <252>; lcd_hspw = <10>; lcd_vt = <1127>; lcd_vbp = <36>; lcd_vspw = <5>; lcd_width = <217>; lcd_height = <136>; lcd_lvds_if = <1>; lcd_lvds_colordepth = <0>; lcd_lvds_mode = <1>; lcd_frm = <1>; lcd_cmap_en = <0>; lcd_rb_swap = <0>; lcd_tcon_div = <7>; lcd_hv_clk_phase = <0>; lcd_hv_sync_polarity= <0>; lcd_gamma_en = <0>; lcd_bright_curve_en = <0>; lcd_fsync_en = <0>; lcd_fsync_act_time = <1000>; lcd_fsync_dis_time = <1000>; lcd_fsync_pol = <0>; deu_mode = <0>; lcdgamma4iep = <22>; smart_color = <90>; lcd_pwm_used = <1>; lcd_pwm_ch = <2>; lcd_pwm_freq = <10000>; lcd_pwm_pol = <1>; lcd_pwm_max_limit = <255>; lcd_backlight = <50>; lcd_bl_en = <&pio PD 22 1 0 3 1>; //lcd_gpio_0 = <&pio PD 22 1 0 3 1>; lcd_pin_power = "dcdc1"; lcd_power = "dc1sw"; pinctrl-0 = <&lvds2link_pins_a>; pinctrl-1 = <&lvds2link_pins_b>; };麻烦有遇到的朋友指点一下
-
回复: A133 起不来发布在 其它全志芯片讨论区
[130]HELLO! SBOOT is starting! [133]sboot commit : 54b5c2f5b3 [136]set pll start [138]periph0 has been enabled [141]set pll end [142]PL gpio voltage : 3.3V [145][pmu]: bus read error [148]PMU: AXP803 [150][pmu]: bus read error [198]vaild para:1 select dram para0 [202]board init ok, set sys_vol to 950mv! [226]try to probe rtc region [229]DRAM BOOT DRIVE INFO: V0.697 [232]the chip id is 0x1400 [235]the chip id is 0x1400 [237]the chip id is 0x1400 [240]the chip id is 0x1400 [242]the chip id is 0x1400 [245]chip id check OK [255]DRAM_VCC set to 1200 mv [258]DRAM CLK =744 MHZ [260]DRAM Type =4 (3:DDR3,4:DDR4,6:LPDDR2,7:LPDDR3,8:LPDDR4) [269]DRAM SIZE =1024 MBytes, para1 = 60fa, para2 = 4000000, tpr13 = 80007501 [278]DRAM simple test OK. [280]chipid = 53801400 [283]nsi init ok 2020-4-7 [285][mmc]: mmc driver ver 2020-05-25 09:40-202007019516 [296][mmc]: Wrong media type 0x0 [299][mmc]: ***Try SD card 2*** [303][mmc]: mmc 2 cmd 8 timeout, err 100 [307][mmc]: mmc 2 cmd 8 err 100 [310][mmc]: mmc 2 send if cond failed [315][mmc]: mmc 2 cmd 55 timeout, err 100 [319][mmc]: mmc 2 cmd 55 err 100 [322][mmc]: mmc 2 send app cmd failed [326][mmc]: ***Try MMC card 2*** [351][mmc]: RMCA OK! [353][mmc]: bias 4 [354][mmc]: mmc 2 bias 4 [358][mmc]: MMC 5.1 [360][mmc]: HSSDR52/SDR25 8 bit [363][mmc]: 50000000 Hz [365][mmc]: 7456 MB [367][mmc]: ***SD/MMC 2 init OK!!!*** [399]read toc1 from emmc 32800 sector [403]OLD version: 0.0 [405]NEW version: 0.0 [468]load rotpk hash [516]load monitor-key hash [519]load monitor hash [673]set arisc reset to assert state [681]set arisc reset to de-assert state [733]load boot-key hash [736]load boot hash [787]load vbmeta-key hash [789]load vbmeta hash [841]load recovery-key hash [844]load recovery hash [847]monitor entry=0x48000000 [850]uboot entry=0x4a000000 [853]optee entry=0x48600000 [856]tunning data addr:0x4a0003e8 [859]run out of boot0 NOTICE: BL3-1: v1.0(debug):0f6655c NOTICE: BL3-1: Built : 15:24:20, 2022-07-05 NOTICE: BL3-1 commit: 8 NOTICE: info v0.0 NOTICE: cpuidle init version V1.0 NOTICE: secure os exist MESSAGE: [0x0] TEE-CORE: OP-TEE version: f37cc616 #1 Wed Jan 15 03:00:40 UTC 2020 arm NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05 (Jan 11 2023 - 07:09:48 +0000) Allwinner Technology [00.956]CPU: Allwinner Family [00.959]Model: sun50iw10 I2C: ready [01.077]DRAM: 1 GiB [01.080]Relocation Offset is: 35f05000 [01.110]secure enable bit: 1 [01.114][ARISC ERROR] :get [allwinner,sunxi-hwspinlock] device node error CACHE: Misaligned operation at range [7ffa76e0, 7ffa79f8] [SCP] :sunxi-arisc driver begin startup 2 [SCP] :0x1 [SCP] :arisc version: [e08bf86ebc1eb22d80c2048eb0805b2501510f7frid-] [SCP] :arisc startup ready [SCP] :arisc startup notify message feedback [SCP] :send hard sync feedback message: 0x900200 [SCP] :sunxi-arisc driver v1.10 is starting [01.154]pmu_axp806_probe pmic_bus_read fail [01.158]PMU: AXP803 [01.275]PMU: AXP803 FDT ERROR:fdt_get_regulator_name:get property handle twi-for-pmu-supply error:FDT_ERR_INTERNAL bias_name:pc_bias bias_vol:1800 [01.331]TCS: TCS_probe [01.333]pmu_tcs4838_probe pmic_bus_read fail [01.337]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [01.344]drv_disp_init request pwm success, pwm0:pwm0:0x300a000. [01.397]drv_disp_init finish [01.402]gic: sec monitor mode [01.405]flash init start [01.407]workmode = 0,storage type = 2 [01.410][mmc]: mmc driver ver uboot2018:2020-5-25 9:26:00-2021-09-17 14:45:00 [01.418][mmc]: get sdc_type fail and use default host:tm4. [01.430][mmc]: SUNXI SDMMC Controller Version:0x50300 [01.455][mmc]: Best spd md: 4-HS400, freq: 3-100000000, Bus width: 8 [01.461]sunxi flash init ok [01.465]Loading Environment from SUNXI_FLASH... OK [01.472]Item0 (Map) magic is bad [01.475]the secure storage item0 copy0 magic is bad [01.479]Item0 (Map) magic is bad [01.482]the secure storage item0 copy1 magic is bad [01.487]Item0 (Map) magic is bad secure storage read widevine fail [01.493]secure storage read widevine fail with:-1 secure storage read ec_key fail [01.500]secure storage read ec_key fail with:-1 [01.505]usb burn from boot delay time 0 weak:otg_phy_config [01.516]usb prepare ok [01.950]usb sof ok [01.952]usb probe ok [01.953]usb setup ok set address 0x1a set address 0x1a ok try to update [04.960]do_burn_from_boot usb : have no handshake [04.964]boot_gui_init:start [04.969]set disp.dev2_output_type fail. using defval=0 [04.978]boot_gui_init:finish [04.980]bmp_name=bootlogo.bmp 4096056 bytes read in 25 ms (156.3 MiB/s) no support big size bmp[800x1280] on fb[1024x600] [05.016]show bm[05.018]soc ic_ver:0x4, qa_val:0x0, markid:0x1400 dclk[0-200] display_cfg_flag:0 p on fb failed !-1 [05.034]update dts ** Unrecognized filesystem type ** [05.043]load file(ULI/factory/snum.txt) error. ** Unrecognized filesystem type ** [05.056]load file(ULI/factory/mac.txt) error. ** Unrecognized filesystem type ** [05.068]load file(ULI/factory/wifi_mac.txt) error. ** Unrecognized filesystem type ** [05.080]load file(ULI/factory/bt_mac.txt) error. ** Unrecognized filesystem type ** [05.093]load file(ULI/factory/specialstr.txt) error. [05.103]update part info [05.126]update bootcmd Hit any key to stop autoboot: 0 [05.228]LCD open finish [05.352]not supported key [05.354]actual n size:1000, e:10001 [05.357]exptect n size:800, e:10001 CACHE: Misaligned operation at range [44ffffe0, 465c9020] [05.563]Starting kernel ... [05.566][mmc]: mmc exit start [05.585][mmc]: mmc 2 exit ok [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.170 (zzze@Zzze) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #3 SMP PREEMPT Sun Jan 8 17:31:55 CST 2023 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] disp reserve base 0x7bf53140 ,size 0x258000 [ 0.000000] cma: Reserved 8 MiB at 0x000000007f800000 [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 4096 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 262144 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc03f6e9000 s53376 r8192 d32640 u94208 [ 0.000000] pcpu-alloc: s53376 r8192 d32640 u94208 alloc=23*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258048 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x05000000 initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p4 init=/init partitions=bootloader@mmcblk0p1:env@mmcblk0p2:boot@mmcblk0p3:super@mmcblk0p4:misc@mmcblk0p5:recovery@mmcblk0p6:cache@mmcblk0p7:vbmeta@mmcblk0p8:vbmeta_system@mmcblk0p9:vbmeta_vendor@mmcblk0p10:metadata@mmcblk0p11:private@mmcblk0p12:frp@mmcblk0p13:empty@mmcblk0p14:dtbo@mmcblk0p15:media_data@mmcblk0p16:UDISK@mmcblk0p17 cma=8M snum=2c00142201224711c50 mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.vbmeta.avb_version=2.0 androidboot.vbmeta.hash_alg=sha256 androidboot.vbmeta.size=7168 androidboot.vbmeta.digest=ea9a512f6ccb2b0df9d7821e86fca6e7f8f88fd10254b1c99b2e1742f3122d94 androidboot.vbmeta.device_state=locked androidboot.mode=normal androidboot.serialno=2c00142201224711c50 androidboot.hardware=sun50iw10p1 boot_type=2 androidboot.boot_type=2 androidboot.secure_os_exist=1 androidboot.trustchain=false gpt=1 androidboot.verifiedbootstate[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Memory: 979588K/1048576K available (10942K kernel code, 2208K rwdata, 3948K rodata, 4288K init, 599K bss, 60796K reserved, 8192K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008b30000 ( 10944 KB) [ 0.000000] .rodata : 0xffffff8008b30000 - 0xffffff8008f10000 ( 3968 KB) [ 0.000000] .init : 0xffffff8008f10000 - 0xffffff8009340000 ( 4288 KB) [ 0.000000] .data : 0xffffff8009340000 - 0xffffff8009568008 ( 2209 KB) [ 0.000000] .bss : 0xffffff8009568008 - 0xffffff80095fdc78 ( 600 KB) [ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf01000000 ( 16 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008164] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000) [ 0.018199] pid_max: default: 32768 minimum: 301 [ 0.023037] Security Framework initialized [ 0.026879] SELinux: Initializing. [ 0.030480] SELinux: Starting in permissive mode [ 0.035137] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.041697] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.049550] ftrace: allocating 33752 entries in 132 pages [ 0.131099] sched-energy: CPU device node has no sched-energy-costs [ 0.131737] Invalid sched_group_energy for CPU0 [ 0.136275] CPU0: update cpu_capacity 1024 [ 0.150383] ASID allocator initialised with 32768 entries [ 0.169228] nsi: set limit to fit 720P(ABCDE) [ 0.169461] BOOTEVENT: 169.456665: ON [ 0.202461] Detected VIPT I-cache on CPU1 [ 0.202512] Invalid sched_group_energy for CPU1 [ 0.202515] CPU1: update cpu_capacity 1024 [ 0.202518] CPU1: Booted secondary processor [410fd034] [ 0.225840] Detected VIPT I-cache on CPU2 [ 0.225867] Invalid sched_group_energy for CPU2 [ 0.225870] CPU2: update cpu_capacity 1024 [ 0.225873] CPU2: Booted secondary processor [410fd034] [ 0.249258] Detected VIPT I-cache on CPU3 [ 0.249284] Invalid sched_group_energy for CPU3 [ 0.249286] CPU3: update cpu_capacity 1024 [ 0.249289] CPU3: Booted secondary processor [410fd034] [ 0.249373] Brought up 4 CPUs [ 0.300007] SMP: Total of 4 processors activated. [ 0.304698] CPU features: detected feature: 32-bit EL0 Support [ 0.310504] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.321353] CPU: All CPU(s) started at EL1 [ 0.321776] alternatives: patching kernel code [ 0.326371] Invalid sched_group_energy for CPU3 [ 0.330702] CPU3: update max cpu_capacity 1024 [ 0.335117] Invalid sched_group_energy for Cluster3 [ 0.339970] Invalid sched_group_energy for CPU2 [ 0.344477] Invalid sched_group_energy for Cluster2 [ 0.349329] Invalid sched_group_energy for CPU1 [ 0.353837] Invalid sched_group_energy for Cluster1 [ 0.358689] Invalid sched_group_energy for CPU0 [ 0.363197] Invalid sched_group_energy for Cluster0 [ 0.368565] CPU1: update max cpu_capacity 1024 [ 0.373186] devtmpfs: initialized [ 0.423493] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.427622] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.434394] atomic64_test: passed [ 0.437126] pinctrl core: initialized pinctrl subsystem [ 0.444463] NET: Registered protocol family 16 [ 0.448159] dump_class_init,861, success [ 0.464052] cpuidle: using governor menu [ 0.465421] sunxi iommu: irq = 9 [ 0.466325] vdso: 2 pages (1 code @ ffffff8008b38000, 1 data @ ffffff8009344000) [ 0.472953] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.481078] DMA: preallocated 256 KiB pool for atomic allocations [ 0.488971] sun50iw10p1-r-pinctrl r_pio: initialized sunXi PIO driver [ 0.509537] sun50iw10p1-pinctrl pio: initialized sunXi PIO driver [ 0.514186] iommu: Adding device 1c0e000.ve to group 0 [ 0.521467] iommu: Adding device soc@03000000:disp1@1 to group 0 [ 0.522724] iommu: Adding device 6000000.disp to group 0 [ 0.527684] iommu: Adding device 6400000.eink to group 0 [ 0.533591] iommu: Adding device 6480000.g2d to group 0 [ 0.572507] pwm module init! [ 0.578172] sunxi-pm debug v3.10 [ 0.579532] SCSI subsystem initialized [ 0.580220] usbcore: registered new interface driver usbfs [ 0.585132] usbcore: registered new interface driver hub [ 0.590382] usbcore: registered new device driver usb [ 0.595512] sunxi_i2c_adap_init()2573 - init [ 0.600053] sunxi_i2c_probe()2292 - [i2c6] twi_drv_used = 1 [ 0.605089] sunxi_i2c_probe()2296 - [i2c6] twi_pkt_interval = 0 [ 0.610987] twi6 supply twi not found, using dummy regulator [ 0.616687] twi_request_gpio()454 - [i2c6] init name: twi6 [ 0.622690] axp20x-i2c 6-0034: AXP20x variant AXP803 found [ 0.637350] axp2101-regulator axp2101-regulator.0: Setting DCDC frequency for unsupported AXP variant [ 0.640959] axp2101-regulator axp2101-regulator.0: Error setting dcdc frequency: -22 [ 0.704272] axp20x-i2c 6-0034: AXP20X driver loaded [ 0.704381] sunxi_i2c_dma_request()1124 - [i2c6] using dma0chan0 (tx) and dma0chan1 (rx)for DMA transfers [ 0.713489] media: Linux media interface: v0.10 [ 0.717634] Linux video capture interface: v2.00 [ 0.723008] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000 [ 0.729251] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000 [ 0.735611] ion_parse_dt_heap_common: id 6 type 6 name secure align 1000 [ 0.742442] drm_base=0x80000000 [ 0.745204] drm_size=0x0 [ 0.747738] tee_base=0x2000000 [ 0.751289] Advanced Linux Sound Architecture Driver Initialized. [ 0.757539] Bluetooth: Core ver 2.22 [ 0.760439] NET: Registered protocol family 31 [ 0.764805] Bluetooth: HCI device and connection manager initialized [ 0.771142] Bluetooth: HCI socket layer initialized [ 0.775991] Bluetooth: L2CAP socket layer initialized [ 0.781051] Bluetooth: SCO socket layer initialized [ 0.787333] clocksource: Switched to clocksource arch_sys_counter [ 0.861388] VFS: Disk quotas dquot_6.6.0 [ 0.861527] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.869355] udc_init,0 [ 0.870585] NET: Registered protocol family 2 [ 0.887528] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.888999] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 0.895581] TCP: Hash tables configured (established 8192 bind 8192) [ 0.901849] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.907695] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.914342] NET: Registered protocol family 1 [ 0.918625] Trying to unpack rootfs image as initramfs... [ 0.951367] Freeing initrd memory: 752K [ 0.952824] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.960059] audit: initializing netlink subsys (disabled) [ 0.962758] audit: type=2000 audit(0.789:1): initialized [ 0.969036] workingset: timestamp_bits=45 max_order=18 bucket_order=0 [ 0.986175] Registering sdcardfs 0.1 [ 0.986749] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.988972] fuse init (API version 7.26) [ 0.994523] SELinux: Registering netfilter hooks [ 1.001544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 1.004564] io scheduler noop registered [ 1.008315] io scheduler deadline registered [ 1.012825] io scheduler cfq registered (default) [ 1.019192] [DISP]disp_module_init [ 1.021033] disp soc@03000000:disp1@1: unable to map de registers [ 1.026725] disp: probe of soc@03000000:disp1@1 failed with error -22 [ 1.033916] [DISP] disp_init,line:2345: [ 1.036758] smooth display screen:0 type:1 mode:4 [ 1.080585] [DISP] Fb_copy_boot_fb,line:1645: [ 1.080629] no boot_fb0 [ 1.082979] [DISP] lcd_clk_config,line:675: [ 1.085747] disp 0, clk: pll(240000000),clk(24000\F0YXK\82\B1\B1\A1288000000),clk(288000000),dclk(48000000) dsi_rate(0) [ 1.086298] [DISP]disp_module_init finish [ 1.095756] uart uart0: get regulator failed [ 1.095794] uart0 supply uart not found, using dummy regulator [ 1.096057] uart0: ttyS0 at MMIO 0x5000000 (irq = 349, base_baud = 1500000) is a SUNXI [ 1.096077] sw_console_setup()1733 - console setup baud 115200 parity n bits 8, flow n [ 1.125715] console [ttyS0] enabled [ 1.125715] console [ttyS0] enabled [ 1.135265] bootconsole [earlycon0] disabled [ 1.135265] bootconsole [earlycon0] disabled [ 1.144359] uart uart1: get regulator failed [ 1.152568] uart1 supply uart not found, using dummy regulator [ 1.159388] uart1: ttyS1 at MMIO 0x5000400 (irq = 350, base_baud = 1500000) is a SUNXI [ 1.168897] uart uart2: get regulator failed [ 1.173747] uart2 supply uart not found, using dummy regulator [ 1.180548] uart2: ttyS2 at MMIO 0x5000800 (irq = 351, base_baud = 1500000) is a SUNXI [ 1.190486] misc dump reg init [ 1.195107] G2D: Module initialized.major:246 [ 1.200853] [drm] Initialized [ 1.204377] Unable to detect cache hierarchy for CPU 0 [ 1.223819] brd: module loaded [ 1.242790] loop: module loaded [ 1.247195] zram: Added device: zram0 [ 1.251555] [NAND][NE] Not found valid nand node on dts [ 1.258039] Boot type 2 [ 1.262942] libphy: Fixed MDIO Bus: probed [ 1.267582] tun: Universal TUN/TAP device driver, 1.6 [ 1.273280] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.280486] PPP generic driver version 2.4.2 [ 1.285532] PPP BSD Compression module registered [ 1.290843] PPP Deflate Compression module registered [ 1.296551] PPP MPPE Compression module registered [ 1.301957] NET: Registered protocol family 24 [ 1.306963] PPTP driver version 0.8.5 [ 1.311446] usbcore: registered new interface driver rtl8150 [ 1.317902] usbcore: registered new interface driver r8152 [ 1.324159] usbcore: registered new interface driver asix [ 1.330315] usbcore: registered new interface driver ax88179_178a [ 1.337246] usbcore: registered new interface driver cdc_ether [ 1.343897] usbcore: registered new interface driver smsc75xx [ 1.350455] usbcore: registered new interface driver smsc95xx [ 1.356989] usbcore: registered new interface driver net1080 [ 1.363435] usbcore: registered new interface driver cdc_subset [ 1.370165] usbcore: registered new interface driver zaurus [ 1.376509] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 1.384924] usbcore: registered new interface driver cdc_ncm [ 1.391309] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.399029] get ehci0-controller, regulator_io is no nocare [ 1.405319] get ehci0-controller wakeup-source is fail. [ 1.411443] sunxi ehci0-controller don't init wakeup source [ 1.417734] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xffffff80095e9a10, 0x:ffffff800963d000, irq_no:162 [ 1.431440] [sunxi-ehci0]: Not init ehci0 [ 1.436098] get ehci1-controller, regulator_io is no nocare [ 1.442379] get ehci1-controller wakeup-source is fail. [ 1.448401] sunxi ehci1-controller don't init wakeup source [ 1.454684] [sunxi-ehci1]: probe, pdev->name: 5200000.ehci1-controller, sunxi_ehci: 0xffffff80095e9d98, 0x:ffffff8009791000, irq_no:164 [ 1.468558] sunxi-ehci 5200000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.478775] sunxi-ehci 5200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 1.488986] sunxi-ehci 5200000.ehci1-controller: irq 356, io mem 0xffffffc03db04010 [ 1.510689] sunxi-ehci 5200000.ehci1-controller: USB 0.0 started, EHCI 1.00 [ 1.518539] sunxi-ehci 5200000.ehci1-controller: ehci_irq: highspeed device connect [ 1.527397] hub 1-0:1.0: USB hub found [ 1.531655] hub 1-0:1.0: 1 port detected [ 1.537080] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.544398] get ohci0-controller, regulator_io is no nocare [ 1.550698] get ohci0-controller wakeup-source is fail. [ 1.556801] sunxi ohci0-controller don't init wakeup source [ 1.563198] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi_ohci: 0xffffff80095ea4a8 [ 1.573678] [sunxi-ohci0]: Not init ohci0 [ 1.578317] get ohci1-controller, regulator_io is no nocare [ 1.584598] get ohci1-controller wakeup-source is fail. [ 1.590622] sunxi ohci1-controller don't init wakeup source [ 1.596995] [sunxi-ohci1]: probe, pdev->name: 5200000.ohci1-controller, sunxi_ohci: 0xffffff80095ea830 [ 1.607658] sunxi-ohci 5200000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.617476] sunxi-ohci 5200000.ohci1-controller: new USB bus registered, assigned bus number 2 [ 1.627247] sunxi-ohci 5200000.ohci1-controller: irq 357, io mem 0xffffffc03db04400 [ 1.695673] hub 2-0:1.0: USB hub found [ 1.699953] hub 2-0:1.0: 1 port detected [ 1.705532] usbcore: registered new interface driver uas [ 1.711657] usbcore: registered new interface driver usb-storage [ 1.718509] usbcore: registered new interface driver ums-alauda [ 1.725234] usbcore: registered new interface driver ums-cypress [ 1.732062] usbcore: registered new interface driver ums-datafab [ 1.738891] usbcore: registered new interface driver ums_eneub6250 [ 1.745914] usbcore: registered new interface driver ums-freecom [ 1.752743] usbcore: registered new interface driver ums-isd200 [ 1.759475] usbcore: registered new interface driver ums-jumpshot [ 1.766392] usbcore: registered new interface driver ums-karma [ 1.773036] usbcore: registered new interface driver ums-onetouch [ 1.779973] usbcore: registered new interface driver ums-realtek [ 1.786800] usbcore: registered new interface driver ums-sddr09 [ 1.793532] usbcore: registered new interface driver ums-sddr55 [ 1.800262] usbcore: registered new interface driver ums-usbat [ 1.806975] usbcore: registered new interface driver usbserial [ 1.813745] usbcore: registered new interface driver option [ 1.820076] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.828205] usb_serial_number:20080411 [ 1.833143] sunxikbd_key_init: key0 vol= 646 code= 115 [ 1.838947] sunxikbd_key_init: key1 vol= 900 code= 114 [ 1.844754] sunxikbd_key_init: key2 vol= 1077 code= 158 [ 1.850648] sunxikbd_key_init: key3 vol= 300 code= 187 [ 1.854017] usb 1-1: new high-speed USB device number 2 using sunxi-ehci [ 1.864031] sunxikbd_key_init: key4 vol= 880 code= 102 [ 1.870167] input: sunxi-keyboard as /devices/virtual/input/input0 [ 1.885320] input: axp803-pek as /devices/platform/soc/7081400.s_twi/i2c-6/6-0034/axp2101-pek.0/input/input1 [ 1.898344] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0 [ 1.905281] sunxi-rtc rtc: RTC enabled [ 1.909862] i2c /dev entries driver [ 1.914262] sunxi cedar version 0.1 [ 1.918328] VE: install start!!! [ 1.918328] [ 1.923767] cedar_ve: cedar-ve the get irq is 347 [ 1.929469] VE: get debugfs_mpp_root is NULL, please check mpp [ 1.929469] [ 1.937730] VE: sunxi ve debug register driver failed! [ 1.937730] [ 1.951794] axp803_ac_power: axp803_ac_power_dt_parse: failed [ 1.951794] [ 1.959992] axp803_ac_power: axp803_ac_power_probe parse device tree err [ 1.959992] [ 1.969308] axp803-ac-power-supply: probe of axp803-ac-power-supply.0 failed with error -22 [ 1.979279] axp803_battery: axp803_bat_power_dt_parse: failed [ 1.979279] [ 1.987440] axp803_battery: axp803_bat_power_probe parse device tree err [ 1.987440] [ 1.996674] axp803-battery-power-supply: probe of axp803-battery-power-supply.0 failed with error -22 [ 2.008539] hub 1-1:1.0: USB hub found [ 2.009384] device-mapper: uevent: version 1.0.3 [ 2.009872] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 2.010031] device-mapper: verity-avb: AVB error handler initialized with vbmeta device: [ 2.010037] Bluetooth: HCI UART driver ver 2.3 [ 2.010043] Bluetooth: HCI UART protocol H4 registered [ 2.010046] Bluetooth: HCI UART protocol LL registered [ 2.010050] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 2.015006] sunxi-mmc sdc2: SD/MMC/SDIO Host Controller Driver(v3.46 2020-6-1 11:33-202006021635) [ 2.015077] sunxi-mmc sdc2: ***ctl-spec-caps*** 308 [ 2.015487] sunxi-mmc sdc2: No vdmmc regulator found [ 2.015492] sunxi-mmc sdc2: No vd33sw regulator found [ 2.015497] sunxi-mmc sdc2: No vd18sw regulator found [ 2.015501] sunxi-mmc sdc2: No vq33sw regulator found [ 2.015505] sunxi-mmc sdc2: No vq18sw regulator found [ 2.018093] sunxi-mmc sdc2: set host busy [ 2.018180] mmc:failed to get gpios [ 2.018442] sunxi-mmc sdc2: sdc set ios:clk 0Hz bm PP pm UP vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.034008] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.050695] sunxi-mmc sdc2: detmode:alway in(non removable) [ 2.050718] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.053184] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.054261] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.054515] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.46 2020-6-1 11:33-202006021635) [ 2.054597] sunxi-mmc sdc1: ***ctl-spec-caps*** 8 [ 2.054667] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.054739] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.055958] sunxi-mmc sdc1: No vmmc regulator found [ 2.055962] sunxi-mmc sdc1: No vqmmc regulator found [ 2.055967] sunxi-mmc sdc1: No vdmmc regulator found [ 2.055971] sunxi-mmc sdc1: No vd33sw regulator found [ 2.055975] sunxi-mmc sdc1: No vd18sw regulator found [ 2.055980] sunxi-mmc sdc1: No vq33sw regulator found [ 2.055984] sunxi-mmc sdc1: No vq18sw regulator found [ 2.057186] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.057681] sunxi-mmc sdc1: set host busy [ 2.057757] mmc:failed to get gpios [ 2.057783] sunxi-mmc sdc1: min-frequency:400000 [ 2.058010] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.058034] sunxi-mmc sdc1: no vqmmc,Check if there is regulator [ 2.058582] random: fast init done [ 2.074008] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.075421] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 2.088791] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 8 timing LEGACY(SDR12) dt B [ 2.090696] sunxi-mmc sdc1: detmode:manually by software [ 2.090989] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS200 dt B [ 2.091480] sunxi-mmc sdc2: sdc set ios:clk 100000000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS200 dt B [ 2.091655] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.091770] sunxi-mmc sdc2: sdc set ios:clk 100000000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS(SDR20) dt B [ 2.091920] sunxi-mmc sdc2: sdc set ios:clk 52000000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS(SDR20) dt B [ 2.092149] sunxi-mmc sdc2: sdc set ios:clk 50000000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS400 dt B [ 2.092258] sunxi_mmc_get_hs400_cmd_dly,222 [ 2.092266] sunxi-mmc sdc2: failed to get HS400_cmd used default [ 2.092310] sunxi-mmc sdc2: sdc set ios:clk 100000000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS400 dt B [ 2.092416] sunxi_mmc_get_hs400_cmd_dly,222 [ 2.092424] sunxi-mmc sdc2: failed to get HS400_cmd used default [ 2.092568] mmc0: new HS400 MMC card at address 0001 [ 2.094149] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.095439] hidraw: raw HID events driver (C) Jiri Kosina [ 2.095571] sunxi-mmc sdc1: card claims to support voltages below defined range [ 2.096744] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB [ 2.097864] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB [ 2.098254] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB [ 2.098643] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB [ 2.099420] usbcore: registered new interface driver usbhid [ 2.099422] usbhid: USB HID core driver [ 2.099804] ashmem: initialized [ 2.100588] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [ 2.101812] optee: probing for conduit method from DT. [ 2.102429] optee: initialized driver [ 2.103184] usbcore: registered new interface driver snd-usb-audio [ 2.106006] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.106138] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.106318] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.106910] sunxi-internal-codec codec: pa_power_always_on get failed and set it off. [ 2.106917] digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_power_always_on:0 [ 2.106926] adcdrc_cfg:2, adchpf_cfg:1, dacdrc_cfg:2, dachpf:0 [ 2.106956] gpio-spk:166 [ 2.107077] sunxi-internal-codec codec: [sunxi_internal_codec_probe] codec probe finished. [ 2.108297] [sunxi_card_init] card init finished. [ 2.108574] Audio: [soc_new_pcm] -> 2699 [ 2.108579] Audio: [soc_new_pcm] -> 2718 [ 2.108697] Audio: [soc_new_pcm] -> 2746 [ 2.109222] sunxi-codec-machine sndcodec: sun50iw10codec <-> codec mapping ok [ 2.110650] mmc1: new high speed SDIO card at address 0001 [ 2.111376] input: sun50iw10-codec sunxi Audio Jack as /devices/platform/soc/sndcodec/sound/card0/input2 [ 2.111803] [audio] hp_detect_case: 0 [ 2.111808] [audio] noheadphonemic missing or it has headphonemic. [ 2.112069] sunxi-codec-machine sndcodec: [sunxi_card_dev_probe] register card finished. [ 2.112543] u32 classifier [ 2.112546] Actions configured [ 2.112554] Netfilter messages via NETLINK v0.30. [ 2.112571] nfnl_acct: registering with nfnetlink. [ 2.112870] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 2.113099] ctnetlink v0.93: registering with nfnetlink. [ 2.113632] xt_time: kernel timezone is -0000 [ 2.113732] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 2.114451] gre: GRE over IPv4 demultiplexor driver [ 2.114455] ip_gre: GRE over IPv4 tunneling driver [ 2.115636] IPv4 over IPsec tunneling driver [ 2.140635] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.140957] arp_tables: arp_tables: (C) 2002 David S. Miller [ 2.151346] Initializing XFRM netlink socket [ 2.151382] IPsec XFRM device driver [ 2.152210] NET: Registered protocol family 10 [ 2.153908] mip6: Mobile IPv6 [ 2.153941] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.174014] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.175474] NET: Registered protocol family 17 [ 2.175506] NET: Registered protocol family 15 [ 2.175540] l2tp_core: L2TP core driver, V2.0 [ 2.175554] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 2.182913] Registered cp15_barrier emulation handler [ 2.182924] Registered setend emulation handler [ 2.183855] registered taskstats version 1 [ 2.198980] sid_rd_ver_reg()418 - ver >= 4, soc ver:4 [ 2.199561] sun50i_cpufreq_nvmem: using table: b0 [ 2.202519] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 2.202530] cpu cpu0: _opp_add: OPP not supported by regulators (1464000000) [ 2.202856] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 2.202861] cpu cpu0: _opp_add: OPP not supported by regulators (1608000000) [ 2.202908] cpu cpu1: opp_list_debug_create_link: Failed to create link [ 2.202914] cpu cpu1: _add_opp_dev: Failed to register opp debugfs (-12) [ 2.202950] cpu cpu2: opp_list_debug_create_link: Failed to create link [ 2.202955] cpu cpu2: _add_opp_dev: Failed to register opp debugfs (-12) [ 2.202991] cpu cpu3: opp_list_debug_create_link: Failed to create link [ 2.202996] cpu cpu3: _add_opp_dev: Failed to register opp debugfs (-12) [ 2.205043] get usb_detect_mode is fail, 22 [ 2.205860] switch_init: hall is not used [ 2.209736] sunxi-rtc rtc: setting system clock to 1970-01-01 00:00:24 UTC (24) [ 2.210780] axp803-dcdc6: disabling [ 2.211620] axp803-dldo1: disabling [ 2.212227] axp803-dldo2: disabling [ 2.212834] axp803-dldo3: disabling [ 2.213441] axp803-dldo4: disabling [ 2.214053] axp803-eldo2: disabling [ 2.214668] axp803-eldo3: disabling [ 2.215951] ALSA device list: [ 2.215954] #0: sun50iw10-codec [ 2.935816] hub 1-1:1.0: 4 ports detected [ 2.938107] Freeing unused kernel memory: 4288K [ 2.938174] Kernel init done [ 2.945780] init: init first stage started! [ 2.946725] init: [libfs_mgr]ReadFstabFromDt(): failed to read fstab from dt [ 2.949412] init: Using Android DT directory /proc/device-tree/firmware/android/ [ 2.979451] init: [libfs_mgr]Created logical partition system on device /dev/block/dm-0 [ 2.989861] init: [libfs_mgr]Created logical partition vendor on device /dev/block/dm-1 [ 3.000237] init: [libfs_mgr]Created logical partition product on device /dev/block/dm-2 [ 3.009964] init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/by-name/metadata [ 3.019244] init: [libfs_mgr]Filesystem on /dev/block/by-name/metadata was not cleanly shutdown; state flags: 0x1, incompat feature flags: 0x46 [ 3.034090] init: [libfs_mgr]check_fs(): mount(/dev/block/by-name/metadata,/metadata,ext4)=-1: No such file or directory [ 3.046411] init: [libfs_mgr]Not running /system/bin/e2fsck on /dev/block/mmcblk0p11 (executable not in system image) [ 3.062395] EXT4-fs (mmcblk0p11): recovery complete [ 3.068305] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: errors=panic [ 3.078132] plugin --> switch:1 [ 3.103690] EXT4-fs (dm-0): mounted filesystem without journal. Opts: barrier=1 [ 3.119458] EXT4-fs (dm-1): mounted filesystem without journal. Opts: barrier=1 [ 3.130745] EXT4-fs (dm-2): mounted filesystem without journal. Opts: barrier=1 [ 3.142991] FAT-fs (mmcblk0p16): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 3.181660] FAT-fs (mmcblk0p16): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 3.192882] SELinux: Unable to set superblock options before the security server is initialized [ 3.215157] init: 16 output lines suppressed due to ratelimiting [ 3.226539] random: init: uninitialized urandom read (40 bytes read) [ 3.322226] random: init: uninitialized urandom read (40 bytes read) [ 3.339819] init: Loading SELinux policy [ 3.355131] SELinux: 8192 avtab hash slots, 22216 rules. [ 3.373042] SELinux: 8192 avtab hash slots, 22216 rules. [ 3.379044] SELinux: 1 users, 4 roles, 1369 types, 0 bools, 1 sens, 1024 cats [ 3.387150] SELinux: 97 classes, 22216 rules [ 3.395587] SELinux: Completing initialization. [ 3.400784] SELinux: Setting up existing superblocks. [ 3.494551] audit: type=1403 audit(25.786:2): policy loaded auid=4294967295 ses=4294967295 [ 3.504122] selinux: SELinux: Loaded policy from /vendor/etc/selinux/precompiled_sepolicy [ 3.504122] [ 3.521317] selinux: SELinux: Skipping /product/etc/selinux/product_file_contexts: empty file [ 3.521317] [ 3.532960] selinux: SELinux: Loaded file_contexts [ 3.532960] [ 3.545322] random: init: uninitialized urandom read (40 bytes read) [ 3.593516] init: init second stage started! [ 3.603198] FAT-fs (mmcblk0p16): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 3.648146] init: Using Android DT directory /proc/device-tree/firmware/android/ [ 3.662640] selinux: SELinux: Skipping /product/etc/selinux/product_file_contexts: empty file [ 3.662640] [ 3.674273] selinux: SELinux: Loaded file_contexts [ 3.674273] [ 3.681342] init: Running restorecon... [ 3.705950] init: Overriding previous 'ro.' property 'ro.product.locale':'zh-CN' with new value 'zh-Hans-CN' [ 3.717482] init: Overriding previous 'ro.' property 'pm.dexopt.shared':'speed' with new value 'quicken' [ 3.728239] init: Overriding previous 'ro.' property 'ro.kernel.android.checkjni':'0' with new value '1' [ 3.741668] selinux: avc: denied { set } for scontext=u:r:vendor_init:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service permissive=1 [ 3.741668] [ 3.759019] selinux: avc: denied { set } for scontext=u:r:vendor_init:s0 tcontext=u:object_r:dalvik_prop:s0 tclass=property_service permissive=1 [ 3.759019] [ 3.939460] ueventd: ueventd started! [ 3.948143] selinux: SELinux: Skipping /product/etc/selinux/product_file_contexts: empty file [ 3.948143] [ 3.952496] apexd: Bootstrap subcommand detected [ 3.958928] apexd: Scanning /system/apex for embedded keys [ 3.960386] apexd: Scanning /product/apex for embedded keys [ 3.960538] apexd: ... does not exist. Skipping [ 3.960714] apexd: Scanning /system/apex looking for APEX packages. [ 3.960975] apexd: Found /system/apex/com.android.tzdata [ 3.961584] apexd: Successfully bind-mounted flattened package /system/apex/com.android.tzdata on /apex/com.android.tzdata@290000000 [ 3.961838] apexd: Found /system/apex/com.android.runtime.release [ 3.962395] apexd: Successfully bind-mounted flattened package /system/apex/com.android.runtime.release on /apex/com.android.runtime@1 [ 3.962626] apexd: Found /system/apex/com.android.media.swcodec [ 3.966735] apexd: 9 output lines suppressed due to ratelimiting [ 4.042690] selinux: SELinux: Loaded file_contexts [ 4.042690] [ 4.049966] ueventd: Parsing file /ueventd.rc... [ 4.056376] ueventd: Parsing file /vendor/ueventd.rc... [ 4.063279] ueventd: Parsing file /odm/ueventd.rc... [ 4.068938] ueventd: Unable to read config file '/odm/ueventd.rc': open() failed: No such file or directory [ 4.079917] ueventd: Parsing file /ueventd.sun50iw10p1.rc... [ 4.086327] ueventd: Unable to read config file '/ueventd.sun50iw10p1.rc': open() failed: No such file or directory [ 4.319743] ueventd: Coldboot took 0.22 seconds [ 4.355414] Registered swp emulation handler [ 4.380313] audit: type=1400 audit(26.670:3): avc: denied { setattr } for pid=1158 comm="init" name="/" dev="mmcblk0p16" ino=1 scontext=u:r:vendor_init:s0 tcontext=u:object_r:oemfs:s0 tclass=dir permissive=1 [ 4.435022] EXT4-fs (mmcblk0p17): Ignoring removed nomblk_io_submit option [ 4.473402] logd.auditd: start [ 4.515323] EXT4-fs (mmcblk0p17): recovery complete [ 4.521399] EXT4-fs (mmcblk0p17): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit [ 4.892615] e2fsck: e2fsck 1.44.4 (18-Aug-2018) [ 4.892615] [ 4.899460] e2fsck: Pass 1: Checking inodes, blocks, and sizes [ 4.899460] [ 4.907660] e2fsck: Pass 2: Checking directory structure [ 4.907660] [ 4.915278] e2fsck: Pass 3: Checking directory connectivity [ 4.915278] [ 4.923218] e2fsck: Pass 4: Checking reference counts [ 4.923218] [ 4.930544] e2fsck: Pass 5: Checking group summary information [ 4.930544] [ 4.938747] e2fsck: /dev/block/by-name/UDISK: 1795/279440 files (6.5% non-contiguous), 45824/1116667 blocks [ 4.938747] [ 4.954970] EXT4-fs (mmcblk0p17): mounted filesystem with ordered data mode. Opts: discard [ 4.965867] EXT4-fs (mmcblk0p7): Ignoring removed nomblk_io_submit option [ 4.977937] EXT4-fs (mmcblk0p7): recovery complete [ 4.983803] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit [ 5.078491] e2fsck: e2fsck 1.44.4 (18-Aug-2018) [ 5.078491] [ 5.085336] e2fsck: Pass 1: Checking inodes, blocks, and sizes [ 5.085336] [ 5.093537] e2fsck: Pass 2: Checking directory structure [ 5.093537] [ 5.102207] EXT4-fs (mmcblk0p7): Ignoring removed nomblk_io_submit option [ 5.111625] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: barrier=1,data=ordered,nomblk_io_submit,noauto_da_alloc,errors=panic [ 5.150805] init: 4 output lines suppressed due to ratelimiting [ 5.162687] zram0: detected capacity change from 0 to 762482688 [ 5.195687] mkswap: Swapspace size: 744608k, UUID=2d045edb-899d-453c-bec0-5e58d04ac7e1 [ 5.205374] Adding 744608k swap on /dev/block/zram0. Priority:-1 extents:1 across:744608k SS console:/ $ Keymaster_V4_CreateEntryPoint keymaster load rsa_key error! keymaster load hardware attestation key fail! [ 5.486272] vdc: Waited 0ms for vold [ 5.516120] fscrypt: AES-256-CTS-CBC using implementation "cts(cbc-aes-ce)" [ 5.611899] fscrypt: AES-256-XTS using implementation "xts-aes-ce" [ 5.654340] apexd: Marking APEXd as starting [ 5.659987] apexd: Scanning /system/apex for embedded keys [ 5.668304] apexd: Scanning /product/apex for embedded keys [ 5.674746] apexd: ... does not exist. Skipping [ 5.679976] apexd: Populating APEX database from mounts... [ 5.686618] apexd: Failed to walk /product/apex : Can't open /product/apex for reading : No such file or directory [ 5.699030] apexd: Found "/apex/com.android.tzdata@290000000" [ 5.705725] apexd: Found "/apex/com.android.runtime@1" [ 5.711764] apexd: 2 packages restored. [ 5.716297] apexd: Scanning /data/apex/sessions looking for sessions to be activated. [ 5.760632] vdc: Waited 0ms for vold [ 5.854745] type=1400 audit(28.146:4): avc: denied { setattr } for comm="init" name="audio_d" dev="mmcblk0p17" ino=71858 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 5.854762] init: Setting policy on /data/audio_d [ 5.881779] type=1400 audit(28.146:4): avc: denied { setattr } for comm="init" name="audio_d" dev="mmcblk0p17" ino=71858 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 5.903224] type=1400 audit(28.146:5): avc: denied { read } for comm="init" name="audio_d" dev="mmcblk0p17" ino=71858 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 5.903418] init: Policy for /data/audio_d set to 160cce2f0f2365c0 modes 1/4 [ 5.932562] type=1400 audit(28.146:5): avc: denied { read } for comm="init" name="audio_d" dev="mmcblk0p17" ino=71858 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 5.953779] type=1400 audit(28.146:6): avc: denied { open } for comm="init" path="/data/audio_d" dev="mmcblk0p17" ino=71858 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 5.975679] type=1400 audit(28.146:6): avc: denied { open } for comm="init" path="/data/audio_d" dev="mmcblk0p17" ino=71858 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 5.997504] type=1400 audit(28.193:7): avc: denied { ioctl } for comm="init" path="/data/audio_d" dev="mmcblk0p17" ino=71858 ioctlcmd=0x6613 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 6.084855] logd.daemon: reinit [ 6.195145] treadahead: /data/vendor/treadahead/readahead_file_offset not exist; [ 6.209539] treadahead: go to open trace [ 6.340348] healthd: No battery devices found [ 6.386815] healthd: battery none chg= [ 6.453479] file system registered [ 6.469127] using random self ethernet address [ 6.483006] using random host ethernet address Gatekeeper_TA_CreateEntryPoint [ 6.539648] type=1400 audit(28.193:7): avc: denied { ioctl } for comm="init" path="/data/audio_d" dev="mmcblk0p17" ino=71858 ioctlcmd=0x6613 scontext=u:r:vendor_init:s0 tcontext=u:object_r:audio_rw_data_file:s0 tclass=dir permissive=1 [ 6.587143] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 01.00.06 [ 7.006510] read descriptors [ 7.037583] read strings [ 7.132618] pvrsrvkm: loading out-of-tree module taints kernel. [ 7.602086] pvrsrvkm gpu: IC version: 0x00000004 [ 7.619080] pvrsrvkm gpu: gpu core id:0x1400 core:504000000 [ 7.661466] pvrsrvkm gpu: set gpu core rate:504000000 freq:504000000-950000uV dfs:0x00000001 [ 7.723503] pvrsrvkm gpu: set gpu core rate:504000000 freq:472500000-950000uV dfs:0x00000002 [ 7.778035] pvrsrvkm gpu: set gpu core rate:504000000 freq:441000000-950000uV dfs:0x00000004 [ 7.826961] pvrsrvkm gpu: set gpu core rate:252000000 freq:252000000-950000uV dfs:0x00000001 [ 7.883098] pvrsrvkm gpu: idle:0 dvfs:0 power:0 Yes mode:1 volt:950000 core:504000000 [ 7.914727] PVR_K: 1713: Read BVNC 22.102.54.38 from HW device registers [ 7.947675] PVR_K: 1713: RGX Device registered with BVNC 22.102.54.38 [ 7.987949] [drm] Initialized pvr 1.11.5516664 20170530 on minor 0 [ 8.020047] PVR_K: 1719: RGX Firmware image 'rgx.fw.22.102.54.38' loaded [ 8.733075] init: Received control message 'start' for 'bootanim' from pid: 1719 (/system/bin/surfaceflinger) [ 8.749095] init: starting service 'bootanim'... [ 9.058557] init: Received control message 'interface_start' for 'android.hardware.camera.provider@2.4::ICameraProvider/legacy/0' from pid: 1536 (/system/bin/hwservicemanager) [ 9.391612] selinux: avc: denied { set } for property=display.frame.log pid=1703 uid=1000 gid=1003 scontext=u:r:hal_graphics_composer_default:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service permissive=1 [ 9.391612] [ 10.059768] init: Received control message 'interface_start' for 'android.hardware.camera.provider@2.4::ICameraProvider/legacy/0' from pid: 1536 (/system/bin/hwservicemanager) [ 10.165731] random: crng init done [ 10.169547] random: 7 urandom warning(s) missed due to ratelimiting [ 13.182599] healthd: battery none chg= [ 14.295536] healthd: battery none chg= [ 14.301350] healthd: battery none chg= [ 14.786406] init: processing action (sys.sysctl.extra_free_kbytes=*) from (/init.rc:806) [ 15.481806] acc_open [ 15.484305] acc_release [ 15.762066] init: Received control message 'interface_start' for 'android.hardware.wifi@1.0::IWifi/default' from pid: 1536 (/system/bin/hwservicemanager) [ 15.779108] init: starting service 'vendor.wifi_hal_legacy'... [ 15.789454] init: Received control message 'interface_start' for 'android.hardware.wifi@1.0::IWifi/default' from pid: 1536 (/system/bin/hwservicemanager) [ 18.778205] binder_alloc: 2096: binder_alloc_buf, no vma [ 18.784322] binder: 1715:1896 transaction failed 29189/-3, size 92-0 line 3235 [ 18.787979] binder: undelivered transaction 13164, process died. [ 21.781427] init: processing action (sys.boot_completed=1) from (/init.rc:800) [ 21.809813] sdcardfs version 2.0 [ 21.809819] sdcardfs: dev_name -> /data/media [ 21.809821] sdcardfs: options -> fsuid=1023,fsgid=1023,multiuser,derive_gid,default_normal,unshared_obb,mask=6,userid=0,gid=1015 [ 21.809825] sdcardfs: mnt -> ffffffc00e798aa0 [ 21.809923] sdcardfs: mounted on top of /data/media type ext4 [ 21.811368] Remount options were mask=23,gid=9997 for vfsmnt ffffffc033ade020. [ 21.811382] sdcardfs : options - debug:1 [ 21.811385] sdcardfs : options - gid:9997 [ 21.811387] sdcardfs : options - mask:23 [ 21.811980] Remount options were mask=7,gid=9997 for vfsmnt ffffffc033adefe0. [ 21.811993] sdcardfs : options - debug:1 [ 21.811995] sdcardfs : options - gid:9997 [ 21.811997] sdcardfs : options - mask:7 [ 21.812557] Remount options were mask=7,gid=9997 for vfsmnt ffffffc023a2e560. [ 21.812570] sdcardfs : options - debug:1 [ 21.812573] sdcardfs : options - gid:9997 [ 21.812575] sdcardfs : options - mask:7 [ 21.978101] init: processing action (sys.boot_completed=1) from (/vendor/etc/init/hw/init.device.rc:43) [ 21.991020] axp803_usb_power: current limit not set: usb adapter type [ 21.991020] [ 22.022865] init: Service 'bootanim' (pid 1908) exited with status 0 [ 22.030034] init: Sending signal 9 to service 'bootanim' (pid 1908) process group... [ 22.039161] libprocessgroup: Successfully killed process cgroup uid 1003 pid 1908 in 0ms [ 22.051240] init: processing action (sys.boot_completed=1) from (/system/etc/init/aw_thermal.rc:10) [ 22.061871] init: starting service 'aw_thermal'... [ 22.072083] init: processing action (sys.boot_completed=1 && sys.logbootcomplete=1) from (/system/etc/init/bootstat.rc:78) [ 22.074116] selinux: SELinux: Skipping restorecon on directory(/data/system_ce/0) [ 22.074116] [ 22.095708] init: starting service 'exec 12 (/system/bin/bootstat --record_boot_complete --record_boot_reason --record_time_since_factory_reset -l)'... [ 22.260206] treadahead: /data/vendor/treadahead/readahead_file_offset not exist; [ 22.268964] treadahead: go to read trace [ 22.651482] type=1400 audit(31.680:28): avc: denied { getattr } for comm="composer@2.2-se" path="/dev/__properties__/u:object_r:default_prop:s0" dev="tmpfs" ino=9738 scontext=u:r:hal_graphics_composer_default:s0 tcontext=u:object_r:default_prop:s0 tclass=file permissive=1 [ 22.678972] type=1400 audit(1675902609.063:29): avc: denied { search } for comm="CompactionThrea" name="irq" dev="proc" ino=4026531869 scontext=u:r:system_server:s0 tcontext=u:object_r:proc_irq:s0 tclass=dir permissive=1 [ 24.771204] apexd: Can't open /product/apex for reading : No such file or directory [ 32.186654] type=1400 audit(1675902609.063:29): avc: denied { search } for comm="CompactionThrea" name="irq" dev="proc" ino=4026531869 scontext=u:r:system_server:s0 tcontext=u:object_r:proc_irq:s0 tclass=dir permissive=1 [ 32.209079] type=1400 audit(1675902618.603:30): avc: denied { dac_override } for comm="irqbalance" capability=1 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=capability permissive=1 [ 34.199678] type=1400 audit(1675902618.603:30): avc: denied { dac_override } for comm="irqbalance" capability=1 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=capability permissive=1 [ 34.204816] treadahead: read trace end [ 34.222703] type=1400 audit(1675902620.616:31): avc: denied { ptrace } for comm="crash_dump32" scontext=u:r:crash_dump:s0 tcontext=u:r:vendor_init:s0 tclass=process permissive=1 [ 34.340254] logd: logdr: UID=0 GID=0 PID=2983 n tail=50 logMask=8 pid=2478 start=0ns timeout=0ns [ 34.352816] logd: logdr: UID=0 GID=0 PID=2983 n tail=50 logMask=1 pid=2478 start=0ns timeout=0ns [ 34.365066] logd: logdr: UID=0 GID=0 PID=2983 n tail=0 logMask=8 pid=2478 start=0ns timeout=0ns [ 34.376233] logd: logdr: UID=0 GID=0 PID=2983 n tail=0 logMask=1 pid=2478 start=0ns timeout=0ns [ 34.392224] init: Untracked pid 2983 exited with status 0 [ 34.398741] init: Untracked pid 2985 exited with status 0 [ 34.418448] treadahead: parser trace end [ 34.439791] init: Service 'treadahead_trace' (pid 2478) exited with status 0 [ 34.447749] init: Sending signal 9 to service 'treadahead_trace' (pid 2478) process group... [ 34.457630] libprocessgroup: Successfully killed process cgroup uid 0 pid 2478 in 0ms -
A133 起不来发布在 其它全志芯片讨论区
您好，请问大家有没有遇到过A133启动异常的问题，系统跑到02-09 08:32:00.006 2072 2072 D KeyguardClockSwitch: Updating clock: 0832 就停下了，实在是没有找到问题，麻烦大家帮忙看下
dmesg_e.txt
logcat_e.txt
uboot_e.txt -
A133 安全固件怎么刷回非安全固件发布在 编译和烧写问题专区
您好，我使用了pack -v打包的安全固件发现卡在android页面，现在像刷回pack打包的非安全固件，烧写失败
请问，有什么办法时可以刷回去的吗？