修改System init为procd-init后启动卡死

damifan110 LV 5

CPU为T113-s3
系统为d1s最新版的tina+补丁
板子为自制板，没有wifi以及蓝牙

完整启动日志，最后卡在 Trying to connect to SWUpdate...

U-Boot 2018.07-ge987def5-dirty (Dec 31 2022 - 14:39:41 +0000) Allwinner Technology

[00.298]CPU:   Allwinner Family
[00.301]Model: sun8iw20
I2C:   FDT ERROR:fdt_set_all_pin:[twi0]-->FDT_ERR_BADPATH
FDT ERROR:fdt_set_all_pin:[twi1]-->FDT_ERR_BADPATH
ready
[00.322]DRAM:  128 MiB
[00.325]Relocation Offset is: 04eff000
[00.344]secure enable bit: 0
[00.347]smc_tee_inform_fdt failed with: ffff000a
[00.352]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.358]gic: sec monitor mode
sunxi flash map init
[00.363]flash init start
[00.365]workmode = 0,storage type = 2
[00.369][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[00.375][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.400][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000, Bus width: 4
[00.407]sunxi flash init ok
[00.412]Loading Environment from SUNXI_FLASH... OK
[00.437]Item0 (Map) magic is bad
[00.440]the secure storage item0 copy0 magic is bad
[00.455]Item0 (Map) magic is bad
[00.458]the secure storage item0 copy1 magic is bad
[00.463]Item0 (Map) magic is bad
secure storage read widevine fail
[00.469]secure storage read widevine fail with:-1
secure storage read ec_key fail
[00.476]secure storage read ec_key fail with:-1
secure storage read ec_cert1 fail
[00.483]secure storage read ec_cert1 fail with:-1
secure storage read ec_cert2 fail
[00.491]secure storage read ec_cert2 fail with:-1
secure storage read ec_cert3 fail
[00.498]secure storage read ec_cert3 fail with:-1
secure storage read rsa_key fail
[00.505]secure storage read rsa_key fail with:-1
secure storage read rsa_cert1 fail
[00.513]secure storage read rsa_cert1 fail with:-1
secure storage read rsa_cert2 fail
[00.521]secure storage read rsa_cert2 fail with:-1
secure storage read rsa_cert3 fail
[00.528]secure storage read rsa_cert3 fail with:-1
[00.533]out of usb burn from boot: not need burn key
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.542]update part info
[00.545]update bootcmd
[00.548]change working_fdt 0x43ebee70 to 0x43e9ee70
[00.553][mmc]: no mmc-hs400-1_8v!
[00.556][mmc]: delete mmc-hs200-1_8v from dtb
[00.560][mmc]: get max-frequency ok 50000000 Hz
disable nand error: FDT_ERR_BADPATH
[00.577]update dts
Hit any key to stop autoboot:  0 
[01.670]no vendor_boot partition is found
Android's image name: t113-hmi
[01.681]Starting kernel ...

[01.684][mmc]: mmc exit start
[01.703][mmc]: mmc 2 exit ok
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (ubuntu@ubuntu) (arm-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) 6.4.1, GNU ld (GNU Binutils) 2.27) #20 SMP PREEMPT Sat Dec 31 21:53:19 UTC 2022
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x47800000
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440
[    0.000000] pcpu-alloc: s30348 r8192 d22900 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500400 clk_ignore_unused initcall_debug=0 console=ttyS1,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:private@mmcblk0p6:rootfs_data@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun8iw20p1 boot_type=2 androidboot.boot_type=2 gpt=1 uboot_message=2018.07-ge987def5-dirty(12/31/2022-14:39:41) androidboot.dramsize=128 
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 109620K/131072K available (6144K kernel code, 280K rwdata, 1500K rodata, 1024K init, 1165K bss, 13260K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x264/0x3e8 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008016] Switching to timer-based delay loop, resolution 41ns
[    0.014181] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.023872] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.034220] pid_max: default: 32768 minimum: 301
[    0.038962] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.046294] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.054612] CPU: Testing write buffer coherency: ok
[    0.059806] /cpus/cpu@0 missing clock-frequency property
[    0.065141] /cpus/cpu@1 missing clock-frequency property
[    0.070479] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.076631] Setting up static identity map for 0x40100000 - 0x40100060
[    0.083279] rcu: Hierarchical SRCU implementation.
[    0.088485] smp: Bringing up secondary CPUs ...
[    0.094093] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.094213] smp: Brought up 1 node, 2 CPUs
[    0.104007] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.110176] CPU: All CPU(s) started in SVC mode.
[    0.115251] devtmpfs: initialized
[    0.129279] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.137375] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.147238] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.154457] pinctrl core: initialized pinctrl subsystem
[    0.160615] NET: Registered protocol family 16
[    0.166485] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.201423] rtc_ccu: sunxi ccu init OK
[    0.207417] ccu: sunxi ccu init OK
[    0.211215] r_ccu: sunxi ccu init OK
[    0.232056] sun6i-dma 3002000.dma-controller: sunxi dma probed
[    0.239587] iommu: Default domain type: Translated 
[    0.244610] sunxi iommu: irq = 24
[    0.248825] SCSI subsystem initialized
[    0.252791] usbcore: registered new interface driver usbfs
[    0.258350] usbcore: registered new interface driver hub
[    0.263755] usbcore: registered new device driver usb
[    0.269596] Advanced Linux Sound Architecture Driver Initialized.
[    0.276439] Bluetooth: Core ver 2.22
[    0.280077] NET: Registered protocol family 31
[    0.284523] Bluetooth: HCI device and connection manager initialized
[    0.290931] Bluetooth: HCI socket layer initialized
[    0.295822] Bluetooth: L2CAP socket layer initialized
[    0.300899] Bluetooth: SCO socket layer initialized
[    0.306037] pwm module init!
[    0.310070] g2d 5410000.g2d: Adding to iommu group 0
[    0.315384] G2D: rcq version initialized.major:252
[    0.320900] clocksource: Switched to clocksource arch_sys_counter
[    0.335338] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.344649] NET: Registered protocol family 2
[    0.349549] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.357964] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.365654] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.372715] TCP: Hash tables configured (established 1024 bind 1024)
[    0.379158] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.385749] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.392909] NET: Registered protocol family 1
[    0.399366] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.410637] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.416637] ntfs: driver 2.1.32 [Flags: R/W].
[    0.448665] io scheduler mq-deadline registered
[    0.453220] io scheduler kyber registered
[    0.458227] [DISP]disp_module_init
[    0.462199] disp 5000000.disp: Adding to iommu group 0
[    0.467848] [DISP] parser_disp_init_para,line:1430:
[    0.467851] of_property_read fb0_width fail
[    0.493262] display_fb_request,fb_id:0
[    0.500097] [DISP] Fb_copy_boot_fb,line:1445:
[    0.500101] no boot_fb0
[    0.507355] disp_al_manager_apply ouput_type:0
[    0.511172] [DISP]disp_module_init finish
[    0.512363] [DISP] lcd_clk_config,line:774:
[    0.512374] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000)
[    0.512374]      clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000)
[    0.516810] sunxi_sid_init()783 - insmod ok
[    0.541865] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    0.552160] uart uart1: uart1 supply uart not found, using dummy regulator
[    0.559250] uart1: ttyS1 at MMIO 0x2500400 (irq = 34, base_baud = 1500000) is a SUNXI
[    0.567119] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n
򞮮571438] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[    0.584884] printk: console [ttyS1] enabled
[    0.584884] printk: console [ttyS1] enabled
[    0.593773] printk: bootconsole [earlycon0] disabled
[    0.593773] printk: bootconsole [earlycon0] disabled
[    0.604992] uart uart3: uart3 supply uart not found, using dummy regulator
[    0.612974] uart3: ttyS3 at MMIO 0x2500c00 (irq = 35, base_baud = 1500000) is a SUNXI
[    0.622533] misc dump reg init
[    0.627106] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
[    0.634325] [ADDR_MGT] addr_mgt_probe: success.
[    0.639694] dma-buf: Running sanitycheck
[    0.644133] dma-buf: Running dma_fence
[    0.648335] sizeof(dma_fence)=48
[    0.652067] dma-buf: Running dma_fence/sanitycheck
[    0.657449] dma-buf: Running dma_fence/test_signaling
[    0.663133] dma-buf: Running dma_fence/test_add_callback
[    0.669090] dma-buf: Running dma_fence/test_late_add_callback
[    0.675544] dma-buf: Running dma_fence/test_rm_callback
[    0.681415] dma-buf: Running dma_fence/test_late_rm_callback
[    0.687762] dma-buf: Running dma_fence/test_status
[    0.693150] dma-buf: Running dma_fence/test_error
[    0.698424] dma-buf: Running dma_fence/test_wait
[    0.703614] dma-buf: Running dma_fence/test_wait_timeout
[    0.740911] dma-buf: Running dma_fence/test_stub
[    0.746107] dma-buf: Running dma_fence/race_signal_callback
[    0.820904] thread_signal_callback[0] completed 36130 passes, 145 misses
[    0.828460] thread_signal_callback[1] completed 36115 passes, 131 misses
[    0.871085] [DISP] disp_device_attached_and_enable,line:233:
[    0.871091] attached ok, mgr0<-->dev0
[    0.890906] [DISP] disp_device_attached_and_enable,line:236:
[    0.890914] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8
[    0.910909] thread_signal_callback[0] completed 30781 passes, 30780 misses
[    0.918646] thread_signal_callback[1] completed 42488 passes, 42486 misses
[    0.926917] libphy: Fixed MDIO Bus: probed
[    0.932313] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    0.943780] gmac-power0: NULL
[    0.947108] gmac-power1: NULL
[    0.950432] gmac-power2: NULL
[    0.954827] Failed to alloc md5
[    0.958384] eth0: Use random mac address
[    0.963073] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.970395] sunxi-ehci: EHCI SUNXI driver
[    0.975416] get ehci1-controller wakeup-source is fail.
[    0.981396] sunxi ehci1-controller don't init wakeup source
[    0.987653] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0b61928, 0x:c8835000, irq_no:3c
[    0.999704] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
[    1.012220] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    1.024434] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    1.031709] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    1.041723] sunxi-ehci 4200000.ehci1-controller: irq 60, io mem 0x04200000
[    1.070919] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    1.078734] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device connect
[    1.088169] hub 1-0:1.0: USB hub found
[    1.092447] hub 1-0:1.0: 1 port detected
[    1.097388] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.104398] sunxi-ohci: OHCI SUNXI driver
[    1.109367] get ohci1-controller wakeup-source is fail.
[    1.115364] sunxi ohci1-controller don't init wakeup source
[    1.121651] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0b61bb8
[    1.131349] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
[    1.143854] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    1.156055] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    1.163342] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    1.173304] sunxi-ohci 4200400.ohci1-controller: irq 61, io mem 0x04200400
[    1.255714] hub 2-0:1.0: USB hub found
[    1.259960] hub 2-0:1.0: 1 port detected
[    1.265161] usbcore: registered new interface driver uas
[    1.271258] usbcore: registered new interface driver usb-storage
[    1.278025] usbcore: registered new interface driver ums-alauda
[    1.284724] usbcore: registered new interface driver ums-cypress
[    1.291516] usbcore: registered new interface driver ums-datafab
[    1.298295] usbcore: registered new interface driver ums-freecom
[    1.305078] usbcore: registered new interface driver ums-jumpshot
[    1.311959] usbcore: registered new interface driver ums-karma
[    1.318543] usbcore: registered new interface driver ums-onetouch
[    1.325432] usbcore: registered new interface driver ums-sddr09
[    1.332128] usbcore: registered new interface driver ums-sddr55
[    1.338915] i2c /dev entries driver
[    1.342925] sunxi cedar version 1.1
[    1.347066] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    1.353403] VE: sunxi_cedar_probe power-domain init!!!
[    1.359170] VE: install start!!!
[    1.359170] 
[    1.364715] VE: cedar-ve the get irq is 41
[    1.364715] 
[    1.371204] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval)
[    1.371204] 
[    1.380496] VE: install end!!!
[    1.380496] 
[    1.385600] VE: sunxi_cedar_probe
[    1.389574] Bluetooth: HCI UART driver ver 2.3
[    1.394577] Bluetooth: HCI UART protocol H4 registered
[    1.400353] Bluetooth: HCI UART protocol BCSP registered
[    1.406579] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    1.414668] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    1.425939] sunxi-mmc 4022000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.435800] sunxi-mmc 4022000.sdmmc: ***ctl-spec-caps*** 308
[    1.442210] sunxi-mmc 4022000.sdmmc: No vmmc regulator found
[    1.448558] sunxi-mmc 4022000.sdmmc: No vqmmc regulator found
[    1.455018] sunxi-mmc 4022000.sdmmc: No vdmmc regulator found
[    1.461517] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    1.469088] sunxi-mmc 4022000.sdmmc: No vd33sw regulator found
[    1.475700] sunxi-mmc 4022000.sdmmc: No vd18sw regulator found
[    1.482259] sunxi-mmc 4022000.sdmmc: No vq33sw regulator found
[    1.488807] sunxi-mmc 4022000.sdmmc: No vq18sw regulator found
[    1.495378] sunxi-mmc 4022000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    1.504819] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.528576] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.552833] sunxi-mmc 4022000.sdmmc: detmode:alway in(non removable)
[    1.559990] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.572729] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    1.574655] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.582603] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    1.595399] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.600221] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    1.618139] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    1.624645] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    1.631122] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    1.637665] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    1.637924] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.644229] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    1.655917] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.662413] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    1.676987] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.692691] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.703906] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    1.707449] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.724105] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.735521] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.745547] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.745780] usb-storage 1-1:1.0: USB Mass Storage device detected
[    1.755345] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.762207] sunxi-mmc 4020000.sdmmc: detmode:alway in(non removable)
[    1.771979] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01)
[    1.779205] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.789264] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing MMC-HS(SDR20) dt B
[    1.801599] sunxi_led_probe()1749 - start
[    1.812589] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing MMC-HS(SDR20) dt B
[    1.816786] sunxi_get_str_of_property()1595 - failed to get the string of propname led_regulator!
[    1.828697] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing MMC-HS(SDR20) dt B
[    1.838429] scsi host0: usb-storage 1-1:1.0
[    1.850330] sunxi_register_led_classdev()1483 - led_classdev start
[    1.854924] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.861902] sunxi-mmc 4020000.sdmmc: smc 1 p0 err, cmd 8, RTO !!
[    1.873549] sunxi-mmc 4020000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    1.880310] sunxi-mmc 4020000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    1.887169] sunxi-mmc 4020000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    1.894035] sunxi-mmc 4020000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    1.894063] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    1.901020] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing MMC-DDR52 dt B
[    1.908773] sunxi_led_probe()1845 - finish
[    1.919104] mmc0: new DDR MMC card at address 0001
[    1.930517] exFAT: Version 1.3.0
[    1.935877] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB 
[    1.942319] [AUDIOCODEC][sunxi_codec_parse_params][2437]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    1.942319] 
[    1.944157] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (248:0)
[    1.948955] [AUDIOCODEC][sunxi_codec_parse_params][2473]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    1.949415] [AUDIOCODEC][sunxi_internal_codec_probe][2634]:codec probe finished
[    1.975793]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[    1.986233] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    2.008227] [SNDCODEC][sunxi_card_init][583]:card init finished
[    2.015367] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    2.026259] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input0
[    2.038209] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[    2.046603] NET: Registered protocol family 10
[    2.051637] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
[    2.059998] Segment Routing with IPv6
[    2.064258] NET: Registered protocol family 17
[    2.069406] Bluetooth: RFCOMM TTY layer initialized
[    2.074930] Bluetooth: RFCOMM socket layer initialized
[    2.080721] Bluetooth: RFCOMM ver 1.11
[    2.085493] Registering SWP/SWPB emulation handler
[    2.106198] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    2.118715] get ehci0-controller wakeup-source is fail.
[    2.124742] sunxi ehci0-controller don't init wakeup source
[    2.131016] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0b61408, 0x:c88b2000, irq_no:3a
[    2.143032] [sunxi-ehci0]: Not init ehci0
[    2.147860] get ohci0-controller wakeup-source is fail.
[    2.153830] sunxi ohci0-controller don't init wakeup source
[    2.160088] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0b61698
[    2.169766] [sunxi-ohci0]: Not init ohci0
[    2.174971] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
[    2.188408] clk: Not disabling unused clocks
[    2.193382] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.203093] cfg80211: failed to load regulatory.db
[    2.203106] ALSA device list:
[    2.211827]   #0: audiocodec
[    2.215063] alloc_fd: slot 0 not NULL!
[    2.225896] EXT4-fs (mmcblk0p5): mounted filesystem without journal. Opts: (null)
[    2.234407] VFS: Mounted root (ext4 filesystem) readonly on device 179:5.
[    2.242654] devtmpfs: mounted
[    2.247876] Freeing unused kernel memory: 1024K
[    2.271059] Run /sbin/init as init process
[    2.302564] init: Console is alive
[    2.306613] init: - preinit -
/etc/preinit: line 1: strings: not found
/etc/preinit: line 1: head: not found
formating /dev/by-name/UDISK to ext4
mke2fs 1.46.4 (18-Aug-2021)
[    2.451713] random: fast init done
Discarding device blocks:                [    2.490794] random: mkfs.ext4: uninitialized urandom read (1done                            
[    2.499600] random: mkfs.ext4: uninitialized urandom read (16 bytes read)
Creating filesystem with 1360510 4k blocks and 340704 inodes
Filesystem UUID: c259e7de-c4a4-4f64-bfb2-3d0cfdbfa846
Superblock backups stored on blocks: 
	32768, 98304, 163840, 229376, 294912, 819200, 884736

Allocating group tables: done                            
Writing inode tables: done                            
Creating journal (16384 blocks): [    2.953302] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 4
[    2.964012] sd 0:0:0:0: [sda] 15131636 512-byte logical blocks: (7.75 GB/7.21 GiB)
[    2.973256] sd 0:0:0:0: [sda] Write Protect is off
[    2.978638] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[    2.984990] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    3.048896]  sda: sda4
[    3.054875] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    3.322800] random: procd: uninitialized urandom read (4 bytes read)
done
Writing superblocks and filesystem accounting information: done 

formating /dev/by-name/rootfs_data to ext4
mke2fs 1.46.4 (18-Aug-2021)
Discarding device blocks:              [    4.141111] random: mkfs.ext4: uninitialized urandom read (16 bydone                            
[    4.149398] random: mkfs.ext4: uninitialized urandom read (16 bytes read)
Creating filesystem with 524288 4k blocks and 131072 inodes
Filesystem UUID: 2704ad51-f026-4685-b7be-698c3b123cc2
Superblock backups stored on blocks: 
	32768, 98304, 163840, 229376, 294912

Allocating group tables: done                            
Writing inode tables: done                            
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: done 

[    5.688940] mount_root: mounting /dev/root
[    5.693870] EXT4-fs (mmcblk0p5): re-mounted. Opts: (null)
[    5.700096] mount_root: loading kmods from internal overlay
[    5.762620] block: attempting to load /etc/config/fstab
[    5.771258] sunxi_usb_udc 4100000.udc-controller: 4100000.udc-controller supply udc not found, using dummy regulator
e2fsck 1.46.4 (18-Aug-2021)
/dev/by-name/UDISK: clean, 11/340704 files, 43096/1360510 blocks
[    5.803736] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: 
[    5.819708] mount_root: switched to extroot
[    5.830584] procd: - early -
[    5.843791] random: procd: uninitialized urandom read (4 bytes read)
[    5.919511] procd: - ubus -
[    5.923211] procd (1): /proc/138/oom_adj is deprecated, please use /proc/138/oom_score_adj instead.
[    5.930277] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.974527] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.982937] procd: - init -
[    6.154072] file system registered
[    6.173352] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[    6.197754] ======== XRADIO WIFI OPEN ========
[    6.205864] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31   
[    6.213276] [XRADIO] Allocated hw_priv @ (ptrval)
[    6.253085] read descriptors
[    6.256364] read strings
[    6.330325] [XRADIO] Detect SDIO card 0
[    6.500490] android_work: sent uevent USB_STATE=CONNECTED
[    8.471062] [XRADIO] Remove SDIO card 0
[    8.485369] [SBUS_ERR] sdio probe timeout!
[    8.489960] [XRADIO_ERR] sbus_sdio_init failed
[    8.495265] xradio_core_init failed (-110)!
kmodloader done
Trying to connect to SWUpdate...
[   32.530937] usb1-vbus: disabling
[   36.665366] configfs-gadget gadget: high-speed config #1: c
[   36.671783] android_work: sent uevent USB_STATE=CONFIGURED
[   36.678039] android_work: sent uevent USB_STATE=DISCONNECTED
[   36.684489] android_work: sent uevent USB_STATE=CONNECTED
[  123.771071] random: crng init done
[  123.774895] random: 2 urandom warning(s) missed due to ratelimiting

参考网上文档，修改如下内容

damifan110 LV 5

@damifan110 哪位了解原因还请指点一下，多谢多谢

chengwei_peng LV 6

@damifan110 从启动log看，像是已经完成启动了，现在这个更多应该是你开机启动脚本导致的异常的，确认一下/sbin/init的可执行程序是不是正确的，/etc/inittab是否在::askconsole:/bin/ash --login等配置用于终端登录。

damifan110 LV 5

@chengwei_peng 请教一下，您说的sbin/init是在target/allwinner/generice/base-files目录下的吗？目前这个目录下的init文件内容如下

#!/bin/sh
# Copyright (C) 2006 OpenWrt.org
export INITRAMFS=1

if [ -x /rdinit ];then
  exec /rdinit
else
  exec /sbin/init
fi

damifan110 LV 5

@chengwei_peng inittab文件内容如下：

::sysinit:/etc/init.d/rcS S boot
::shutdown:/etc/init.d/rcS K shutdown
::askconsole:/bin/ash --login