T113 (tina) 如何编译打包spi nand flash 固件

jr_online LV 7

有没有大佬能指点一下！！！让我少走点弯路 [抱拳]
目前的思路是在sys_config.fex 把 storage_type 改为5
然后分区表不知道怎么改，用的是128M的spi falsh
接着就是pack

jr_online LV 7

在sys_config.fex 把 storage_type 改为5
分区表修改：

打包编译固件后通过phoenixsuit下载固件到板子上
运行起来可以看到uboot的bootlogo
然后就运行不起来了
报错如下：

有没有大佬能指点一下

柚木鉉 LV 9

bootargs里修改mtd设备，或者用ubi

在env.cfg里

jr_online LV 7

@yuzukitsuru 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

bootargs里修改mtd设备，或者用ubi

在env.cfg里

大佬，能说详细点吗？没弄过你说的，有点懵逼

jr_online LV 7

@yuzukitsuru

大佬，请问一下怎么把文件系统改成squashfs呢？在menuconfig找不到

柚木鉉 LV 9

@jr_online
Target Images --->
[*] squashfs --->

jr_online LV 7

@yuzukitsuru 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online
Target Images --->
[*] squashfs --->

可以了，谢谢大佬[抱拳]

lansecd LV 5

@jr_online 你好，我边也是Nand启动，现在遇到的问题和你一样，你这个env.cfg怎么修改的呢

jr_online LV 7

@lansecd 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online 你好，我边也是Nand启动，现在遇到的问题和你一样，你这个env.cfg怎么修改的呢

rootfstype=squashfs
bootcmd=run setargs_nand boot_normal

lansecd LV 5

@jr_online 这两个地方和你的一样，还是没有跑起来

[    2.345411] hub 2-0:1.0: USB hub found
[    2.349659] hub 2-0:1.0: 1 port detected
[    2.357934] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.369727] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.377228] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.380544] clk: Not disabling unused clocks
[    2.386918] cfg80211: failed to load regulatory.db
[    2.391717] ALSA device list:
[    2.400452]   #0: audiocodec
[    2.403812] alloc_fd: slot 0 not NULL!
[    2.408372] /dev/root: Can't open blockdev
[    2.413024] VFS: Cannot open root device "ubiblock0_5" or unknown-block(0,0): error -6
[    2.421929] Please append a correct "root=" boot option; here are the available partitions:
[    2.431306] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    2.440572] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.61 #108
[    2.447397] Hardware name: Generic DT based system
[    2.452786] [<c010e248>] (unwind_backtrace) from [<c010a870>] (show_stack+0x10/0x14)
[    2.461472] [<c010a870>] (show_stack) from [<c07600a0>] (dump_stack+0x7c/0x98)
[    2.469573] [<c07600a0>] (dump_stack) from [<c011956c>] (panic+0x104/0x3d8)
[    2.477380] [<c011956c>] (panic) from [<c0b01270>] (mount_block_root+0x254/0x2fc)
[    2.485771] [<c0b01270>] (mount_block_root) from [<c0b014d0>] (prepare_namespace+0x138/0x178)
[    2.495329] [<c0b014d0>] (prepare_namespace) from [<c07745a0>] (kernel_init+0x8/0x10c)
[    2.504206] [<c07745a0>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    2.512688] Exception stack(0xc7825fb0 to 0xc7825ff8)
[    2.518348] 5fa0:                                     00000000 00000000 00000000 00000000
[    2.527514] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.536680] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    2.544098] CPU1: stopping
[    2.547131] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.61 #108
[    2.553956] Hardware name: Generic DT based system
[    2.559329] [<c010e248>] (unwind_backtrace) from [<c010a870>] (show_stack+0x10/0x14)
[    2.568011] [<c010a870>] (show_stack) from [<c07600a0>] (dump_stack+0x7c/0x98)
[    2.576108] [<c07600a0>] (dump_stack) from [<c010c648>] (handle_IPI+0xcc/0x168)
[    2.584305] [<c010c648>] (handle_IPI) from [<c033849c>] (gic_handle_irq+0x70/0x78)
[    2.592793] [<c033849c>] (gic_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8)
[    2.601177] Exception stack(0xc7865f80 to 0xc7865fc8)
[    2.606838] 5f80: 0000063c c7ecb4f4 00000000 c0114b40 00000002 c7864000 c0c04e28 c0c04e64
[    2.616006] 5fa0: 4000406a 410fc075 00000000 00000000 c0c627d0 c7865fd0 c0107f94 c0107f84
[    2.625169] 5fc0: 60000113 ffffffff
[    2.629080] [<c01021cc>] (__irq_svc) from [<c0107f84>] (arch_cpu_idle+0x1c/0x38)
[    2.637373] [<c0107f84>] (arch_cpu_idle) from [<c013de94>] (do_idle+0xd0/0x120)
[    2.645568] [<c013de94>] (do_idle) from [<c013e180>] (cpu_startup_entry+0x18/0x20)
[    2.654054] [<c013e180>] (cpu_startup_entry) from [<40102bec>] (0x40102bec)
[    2.661872] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---

jr_online LV 7

@lansecd 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online 这两个地方和你的一样，还是没有跑起来

[    2.345411] hub 2-0:1.0: USB hub found
[    2.349659] hub 2-0:1.0: 1 port detected
[    2.357934] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.369727] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.377228] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.380544] clk: Not disabling unused clocks
[    2.386918] cfg80211: failed to load regulatory.db
[    2.391717] ALSA device list:
[    2.400452]   #0: audiocodec
[    2.403812] alloc_fd: slot 0 not NULL!
[    2.408372] /dev/root: Can't open blockdev
[    2.413024] VFS: Cannot open root device "ubiblock0_5" or unknown-block(0,0): error -6
[    2.421929] Please append a correct "root=" boot option; here are the available partitions:
[    2.431306] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    2.440572] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.61 #108
[    2.447397] Hardware name: Generic DT based system
[    2.452786] [<c010e248>] (unwind_backtrace) from [<c010a870>] (show_stack+0x10/0x14)
[    2.461472] [<c010a870>] (show_stack) from [<c07600a0>] (dump_stack+0x7c/0x98)
[    2.469573] [<c07600a0>] (dump_stack) from [<c011956c>] (panic+0x104/0x3d8)
[    2.477380] [<c011956c>] (panic) from [<c0b01270>] (mount_block_root+0x254/0x2fc)
[    2.485771] [<c0b01270>] (mount_block_root) from [<c0b014d0>] (prepare_namespace+0x138/0x178)
[    2.495329] [<c0b014d0>] (prepare_namespace) from [<c07745a0>] (kernel_init+0x8/0x10c)
[    2.504206] [<c07745a0>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    2.512688] Exception stack(0xc7825fb0 to 0xc7825ff8)
[    2.518348] 5fa0:                                     00000000 00000000 00000000 00000000
[    2.527514] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.536680] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    2.544098] CPU1: stopping
[    2.547131] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.61 #108
[    2.553956] Hardware name: Generic DT based system
[    2.559329] [<c010e248>] (unwind_backtrace) from [<c010a870>] (show_stack+0x10/0x14)
[    2.568011] [<c010a870>] (show_stack) from [<c07600a0>] (dump_stack+0x7c/0x98)
[    2.576108] [<c07600a0>] (dump_stack) from [<c010c648>] (handle_IPI+0xcc/0x168)
[    2.584305] [<c010c648>] (handle_IPI) from [<c033849c>] (gic_handle_irq+0x70/0x78)
[    2.592793] [<c033849c>] (gic_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8)
[    2.601177] Exception stack(0xc7865f80 to 0xc7865fc8)
[    2.606838] 5f80: 0000063c c7ecb4f4 00000000 c0114b40 00000002 c7864000 c0c04e28 c0c04e64
[    2.616006] 5fa0: 4000406a 410fc075 00000000 00000000 c0c627d0 c7865fd0 c0107f94 c0107f84
[    2.625169] 5fc0: 60000113 ffffffff
[    2.629080] [<c01021cc>] (__irq_svc) from [<c0107f84>] (arch_cpu_idle+0x1c/0x38)
[    2.637373] [<c0107f84>] (arch_cpu_idle) from [<c013de94>] (do_idle+0xd0/0x120)
[    2.645568] [<c013de94>] (do_idle) from [<c013e180>] (cpu_startup_entry+0x18/0x20)
[    2.654054] [<c013e180>] (cpu_startup_entry) from [<40102bec>] (0x40102bec)
[    2.661872] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---

那你有没有按照大佬的提议更改menuconfig

lansecd LV 5

@jr_online 也按大佬的来了

jr_online LV 7

@lansecd 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online 也按大佬的来了

那有没有在sys_config.fex 把 storage_type 改为5呢？

lansecd LV 5

@jr_online 打开squashfs的同时，关闭ext4

qqqlb LV 5

This post is deleted!

Justyu666 LV 5

@jr_online 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@yuzukitsuru 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online
Target Images --->
[*] squashfs --->

可以了，谢谢大佬[抱拳]

亲，我按照帖子步骤设置了，但是打包有误，是哪里有问题呢？
图1 sys_config.fex.png

Justyu666 LV 5

@jr_online 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@lansecd 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online 你好，我边也是Nand启动，现在遇到的问题和你一样，你这个env.cfg怎么修改的呢

rootfstype=squashfs
bootcmd=run setargs_nand boot_normal
亲，我按照帖子步骤设置了，但是打包有错误提示，是哪里没配置正确呢？

Justyu666 LV 5

@jr_online 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@lansecd 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online 你好，我边也是Nand启动，现在遇到的问题和你一样，你这个env.cfg怎么修改的呢

rootfstype=squashfs
bootcmd=run setargs_nand boot_normal
亲，我按照帖子步骤配置后打包有错误提示，是哪里没设置对呢？

图4 env.cfg.png

图5 menuconfig.png

图2 sys_partition.fex.png
图2 sys_partition.fex 的打包错误提示.png

图3 sys_partition.fex.png
图3 sys_partition.fex 的打包错误提示.png

请大神指导一下，多谢…………！

jr_online LV 7

@justyu666 参考一下这分区表试试？

;---------------------------------------------------------------------------------------------------
; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串
;---------------------------------------------------------------------------------------------------


;---------------------------------------------------------------------------------------------------
;                                   固件下载参数配置
;---------------------------------------------------------------------------------------------------
;***************************************************************************************************
;    mbr的大小, 以Kbyte为单位
;***************************************************************************************************
[mbr]
size = 252

;***************************************************************************************************
;                                              分区配置
;
;
;  partition 定义范例:
;    [partition]                ;  //表示是一个分区
;    name        = USERFS2      ; //分区名称
;    size        = 16384        ; //分区大小 单位: 扇区.分区表示个数最多2^31 * 512 = 2T
;    downloadfile = "123.fex"   ; //下载文件的路径和名称，可以使用相对路径，相对是指相对于image.cfg文件所在分区。也可以使用绝对路径
;    keydata     = 1            ; //私有数据分区，重新量产数据将不丢失
;    encrypt     = 1            ; //采用加密方式烧录，将提供数据加密，但损失烧录速度
;    user_type   = ?            ; //私有用法
;    verify      = 1            ; //要求量产完成后校验是否正确
;
; 注：1、name唯一, 不允许同名
;     2、name最大12个字符
;     3、size = 0, 将创建一个无大小的空分区
;     4、align to logical block size(504 sectors), leb size = 2*(1 nand phy block size - 1 phy page size)
;***************************************************************************************************
[partition_start]

[partition]
    name         = boot-resource
    size         = 7000
    downloadfile = "boot-resource.fex"
    user_type    = 0x8000

[partition]
    name         = env
    size         = 504
    downloadfile = "env.fex"
    user_type    = 0x8000

[partition]
    name         = env-redund
    size         = 504
    downloadfile = "env.fex"
    user_type    = 0x8000

[partition]
    name         = boot
    size         = 12600
    downloadfile = "boot.fex"
    user_type    = 0x8000

[partition]
    name         = rootfs
    size         = 102400
    downloadfile = "rootfs.fex"
    user_type    = 0x8000

Justyu666 LV 5

@jr_online 好的，谢谢

Justyu666 LV 5

@jr_online 亲，我按照您的分区表改后仍然无法打包，是还要改哪里呢？分区表的 mbr size 改了 252，但是打包提示还是 16384，如下图
图6 sys_partition.fex修改后打包失败.png
麻烦指导一下，谢谢！

jr_online LV 7

@justyu666 在 T113 (tina) 如何编译打包spi nand flash 固件中说：

@jr_online 亲，我按照您的分区表改后仍然无法打包，是还要改哪里呢？分区表的 mbr size 改了 252，但是打包提示还是 16384，如下图

麻烦指导一下，谢谢！

指导算不上，我也是半吊子，你把我上面的分区表复制替换你的分区表试试，总觉得是你的name = boot-resour有问题？不应该是boot-resource咩？不知道跟这个有没有关系