imx307适配v853设备树？
-
请帮忙看看了v853适配imx307
设备树修改了
sensor0:sensor@0 {
device_type = "sensor0";
sensor0_mname = "imx307_mipi";
sensor0_twi_cci_id = <1>;
sensor0_twi_addr = <0x60>;
sensor0_mclk_id = <0>;
sensor0_pos = "rear";
sensor0_isp_used = <1>;
sensor0_fmt = <1>;
sensor0_stby_mode = <0>;
sensor0_vflip = <0>;
sensor0_hflip = <0>;
sensor0_iovdd-supply = <>;
sensor0_iovdd_vol = <1800000>;
sensor0_avdd-supply = <>;
sensor0_avdd_vol = <2800000>;
sensor0_dvdd-supply = <>;
sensor0_dvdd_vol = <1200000>;
sensor0_power_en = <>;
sensor0_reset = <&pio PE 16 1 0 1 0>;
sensor0_pwdn = <&pio PD 5 1 0 1 0>;
status = "okay";
};其他部分添加到Makefile，编译烧录测试的时候，提示
[VIN_ERR]registering imx307_mipi, No such device!imx307_mipi.c驱动文件中显示名称是imx307_mipi
搞不懂要怎么修改
有大神帮忙看看了 -
Moved from 其它全志芯片讨论区 by
xiaowenge
-
有没有完整的log
-
@yuzukitsuru 有下面就是开机完整的log
[210]HELLO! BOOT0 is starting Dec 9 2020 16:17:45! [215]BOOT0 commit : 5689aee [217]board init start [220]set pll start [222]set pll end [224][pmu]: bus read error [226]board init ok [228]chip id check OK [230]DRAM BOOT DRIVE INFO: V0.41 [234]DRAM CLK = 480 MHz [236]DRAM Type = 2 (2:DDR2,3:DDR3) [239]DRAMC read ODT off. [242]DRAM ODT off. [244]DRAM SIZE =64 M [251]DRAM simple test OK. [253]rtc standby flag is 0x0, super standby flag is 0x0 [259]dram size =64 [262]card no is 0 [263]sdcard 0 line count 4 [266][mmc]: mmc driver ver 2019-11-4 14:19 [270][mmc]: sdc0 spd mode error, 2 [273][mmc]: set f_max to 50M, set f_max_ddr to 25M [278][mmc]: mmc 0 bias 0 [286][mmc]: Wrong media type 0x0 [289][mmc]: ***Try SD card 0*** [308][mmc]: HSSDR52/SDR25 4 bit [310][mmc]: 50000000 Hz [313][mmc]: 30436 MB [315][mmc]: ***SD/MMC 0 init OK!!!*** [353]Loading boot-pkg Succeed(index=0). [357]Entry_name = optee [360]Entry_name = u-boot [365]Entry_name = dtb [368]Jump to second Boot. MESSAGE: [0x0] TEE-CORE: OP-TEE version: sun8iw19p1_v0.6.0-27-g7f6d3375 #1 Thu Dec 10 03:28:16 UTC 2020 arm ERROR: [0x0] TEE-CORE:platform_standby_fdt_parse:126: no pmu node ERROR: [0x0] TEE-CORE:sunxi_twi_parse_from_dt:127: no pmu node U-Boot 2018.05-00006-ge196180 (Feb 11 2022 - 15:23:40 +0800) Allwinner Technology [00.437]CPU: Allwinner Family [00.439]Model: sun8iw19 I2C: ready [00.444]DRAM: 64 MiB [00.446]Relocation Offset is: f9f70000 [00.463]secure enable bit: 0 [00.465]pmu_axp2101_probe pmic_bus_read fail [00.469]drivers/sunxi_power/pmu_axpnull.c pmu_axpnull_probe 26 axpdummy probe [00.476]bmu_axp2101_probe pmic_bus_read fail [00.480]BMU: AXPNULL [00.483]CPU=816 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=120Mhz [00.489]gic: sec monitor mode [00.492]flash init start [00.494]workmode = 0,storage type = 1 [00.497]MMC: 0 [00.499]get mem for descripter OK ! card_caps:0x3000000a host_caps:0x3000003f [00.739]sunxi flash init ok [00.743]Loading Environment from SUNXI_FLASH... OK [00.761]update dts root_partition is rootfs set root to /dev/mmcblk0p4 [00.773]update part info [00.775]update bootcmd [00.777]No ethernet found. Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 45000000 ... Image Name: ARM OpenWrt Linux-4.9.118 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3204984 Bytes = 3.1 MiB Load Address: 40008000 Entry Point: 40008000 [02.088]Starting kernel ... [02.090]mmc 2 not find, so not exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.118 (xs@xs-pc) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #9 PREEMPT Fri Oct 28 09:06:17 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: sun8iw19 [ 0.000000] ion_mem_reserve: err format for ion reserve list! [ 0.000000] cma: Reserved 4 MiB at 0x43c00000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat c05bfa3c, node_mem_map c3b77000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x05000000 initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p4 rootwait init=/pseudo_init rdinit=/rdinit partitions=boot-res@mmcblk0p1:env@mmcblk0p2:boot@mmcblk0p3:rootfs@mmcblk0p4:rootfs_data@mmcblk0p5:UDISK@mmcblk0p6 cma=4M mac_addr= wifi_mac= bt_mac= selinux= specialstr= coherent_pool=16K ion_carveout_list= androidboot.mode=normal androidboot.hardware=sun8iw19p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-00006-ge196180(02/11/2022-15:23:40) [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 54448K/65536K available (3355K kernel code, 945K rwdata, 1244K rodata, 140K init, 136K bss, 6992K reserved, 4096K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc4800000 - 0xff800000 ( 944 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) [ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB) [ 0.000000] .text : 0xc0008000 - 0xc034f0c8 (3357 kB) [ 0.000000] .init : 0xc04b1000 - 0xc04d4000 ( 140 kB) [ 0.000000] .data : 0xc04d4000 - 0xc05c05f8 ( 946 kB) [ 0.000000] .bss : 0xc05c05f8 - 0xc05e277c ( 137 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000023] Switching to timer-based delay loop, resolution 41ns [ 0.000168] Console: colour dummy device 80x30 [ 0.000195] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000210] pid_max: default: 32768 minimum: 301 [ 0.000391] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000405] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001021] CPU: Testing write buffer coherency: ok [ 0.001308] Setting up static identity map for 0x400081c0 - 0x4000820c [ 0.003376] devtmpfs: initialized [ 0.030444] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.030941] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.030970] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.031293] atomic64_test: passed [ 0.031308] pinctrl core: initialized pinctrl subsystem [ 0.032352] NET: Registered protocol family 16 [ 0.033732] DMA: preallocated 16 KiB pool for atomic coherent allocations [ 0.035273] dump_class_init,857, success [ 0.036762] sunxi iommu: irq = 23 [ 0.042952] sun8iw19p1-r-pinctrl r_pio: initialized sunXi PIO driver [ 0.059195] sun8iw19p1-pinctrl pio: initialized sunXi PIO driver [ 0.061917] iommu: Adding device 1c0e000.ve to group 0 [ 0.063395] iommu: Adding device 2300000.eise to group 0 [ 0.071005] iommu: Adding device 1480000.g2d to group 0 [ 0.071745] iommu: Adding device 2400000.nna to group 0 [ 0.076481] iommu: Adding device csi0 to group 0 [ 0.077597] iommu: Adding device csi1 to group 0 [ 0.078984] iommu: Adding device 2100000.isp to group 0 [ 0.079959] iommu: Adding device 2104000.scaler to group 0 [ 0.080590] iommu: Adding device 2104400.scaler to group 0 [ 0.081052] iommu: Adding device 2104800.scaler to group 0 [ 0.081606] iommu: Adding device 2104c00.scaler to group 0 [ 0.082691] iommu: Adding device vinc0 to group 0 [ 0.083563] iommu: Adding device vinc1 to group 0 [ 0.125233] pwm module init! [ 0.129199] sunxi-pm debug v3.10 [ 0.132562] SCSI subsystem initialized [ 0.133258] usbcore: registered new interface driver usbfs [ 0.133421] usbcore: registered new interface driver hub [ 0.133559] usbcore: registered new device driver usb [ 0.133800] sunxi_i2c_adap_init()2553 - init [ 0.134349] sunxi_i2c_probe()2213 - [i2c1] warning: failed to get regulator id [ 0.134432] sunxi_i2c_probe()2281 - [i2c1] no_suspend = 0 [ 0.134453] twi1 supply twi not found, using dummy regulator [ 0.134571] twi_request_gpio()452 - [i2c1] init name: twi1 [ 0.135863] media: Linux media interface: v0.10 [ 0.136065] Linux video capture interface: v2.00 [ 0.138584] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000 [ 0.138901] ion_parse_dt_heap_common: id 1 type 1 name sys_contig align 1000 [ 0.139153] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000 [ 0.140591] Advanced Linux Sound Architecture Driver Initialized. [ 0.141568] Bluetooth: Core ver 2.22 [ 0.141706] NET: Registered protocol family 31 [ 0.141718] Bluetooth: HCI device and connection manager initialized [ 0.141743] Bluetooth: HCI socket layer initialized [ 0.141757] Bluetooth: L2CAP socket layer initialized [ 0.144393] G2D: rcq version initialized.major:251 [ 0.145413] clocksource: Switched to clocksource arch_sys_counter [ 0.170914] udc_init,0 [ 0.171100] NET: Registered protocol family 2 [ 0.172498] TCP established hash table entries: 16 (order: -6, 64 bytes) [ 0.172520] TCP bind hash table entries: 16 (order: -6, 64 bytes) [ 0.172530] TCP: Hash tables configured (established 16 bind 16) [ 0.172603] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.172627] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.172814] NET: Registered protocol family 1 [ 0.176520] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.192540] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.197736] NET: Registered protocol family 38 [ 0.197793] io scheduler noop registered [ 0.197803] io scheduler deadline registered [ 0.198112] io scheduler cfq registered (default) [ 0.199980] [DISP]disp_module_init [ 0.200992] [DISP]disp_module_init finish [ 0.202876] uart uart0: get regulator failed [ 0.202906] uart0 supply uart not found, using dummy regulator [ 0.203178] uart0: ttyS0 at MMIO 0x5000000 (irq = 294, base_baud = 1500000) is a SUNXI [ 0.203210] sw_console_setup()1777 - console setup baud 115200 parity n bits 8, flow n [ 1.028180] console [ttyS0] enabled [ 1.033391] misc dump reg init [ 1.038152] sunxi-wlan wlan: wlan_busnum (1) [ 1.042969] sunxi-wlan wlan: wlan_power_num (-1) [ 1.048416] sunxi-wlan wlan: Missing wlan_io_regulator. [ 1.054302] sunxi-wlan wlan: io_regulator_name ((null)) [ 1.060238] sunxi-wlan wlan: request pincrtl handle for device [wlan] failed [ 1.068335] sunxi-wlan wlan: wlan_regon gpio=198 mul-sel=1 pull=0 drv_level=1 data=0 [ 1.077525] sunxi-wlan wlan: get gpio chip_en failed [ 1.083130] sunxi-wlan wlan: wlan_hostwake gpio=199 mul-sel=0 pull=0 drv_level=1 data=0 [ 1.092581] sunxi-wlan wlan: wakeup source is disabled! [ 1.098482] sunxi-wlan wlan: clk_name () [ 1.103884] [ADDR_MGT] addr_mgt_probe: success. [ 1.112396] libphy: Fixed MDIO Bus: probed [ 1.117873] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.125696] get drv_vbus is fail, 84 [ 1.129724] get ehci0-controller, regulator_io is no nocare [ 1.136143] get ehci0-controller wakeup-source is fail. [ 1.142219] sunxi ehci0-controller don't init wakeup source [ 1.148573] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xc05dc9dc, 0x:c4838000, irq_no:129 [ 1.160805] sunxi-ehci 5101000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.171073] sunxi-ehci 5101000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 1.181041] sunxi-ehci 5101000.ehci0-controller: irq 297, io mem 0xc3774800 [ 1.215440] sunxi-ehci 5101000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 1.224556] hub 1-0:1.0: USB hub found [ 1.229077] hub 1-0:1.0: 1 port detected [ 1.234453] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.241909] get drv_vbus is fail, 84 [ 1.246016] get ohci0-controller, regulator_io is no nocare [ 1.252286] get ohci0-controller wakeup-source is fail. [ 1.258427] sunxi ohci0-controller don't init wakeup source [ 1.264783] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi_ohci: 0xc05dc18c [ 1.274587] sunxi-ohci 5101000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.284460] sunxi-ohci 5101000.ohci0-controller: new USB bus registered, assigned bus number 2 [ 1.294233] sunxi-ohci 5101000.ohci0-controller: irq 298, io mem 0xc3775000 [ 1.371176] hub 2-0:1.0: USB hub found [ 1.375684] hub 2-0:1.0: 1 port detected [ 1.381217] usbcore: registered new interface driver uas [ 1.387714] usbcore: registered new interface driver usb-storage [ 1.394716] usbcore: registered new interface driver ums-alauda [ 1.401603] usbcore: registered new interface driver ums-cypress [ 1.408702] usbcore: registered new interface driver ums-datafab [ 1.415722] usbcore: registered new interface driver ums_eneub6250 [ 1.422892] usbcore: registered new interface driver ums-freecom [ 1.429858] usbcore: registered new interface driver ums-isd200 [ 1.436782] usbcore: registered new interface driver ums-jumpshot [ 1.443862] usbcore: registered new interface driver ums-karma [ 1.450680] usbcore: registered new interface driver ums-onetouch [ 1.457870] usbcore: registered new interface driver ums-realtek [ 1.464874] usbcore: registered new interface driver ums-sddr09 [ 1.471739] usbcore: registered new interface driver ums-sddr55 [ 1.478662] usbcore: registered new interface driver ums-usbat [ 1.485344] usb_serial_number:20080411 [ 1.490260] sunxi_gpadc_init,1793, success [ 1.495355] sunxi_key_init: get key count failed [ 1.500663] sunxi_gpadc_setup: get channel compare select failed [ 1.507683] sunxi_gpadc_setup: get channel compare low data select failed [ 1.515322] sunxi_gpadc_setup: get channel compare hig data select failed [ 1.523007] sunxi_gpadc_setup:get channel0_compare_lowdata err! [ 1.529730] sunxi_gpadc_setup:get channel0_compare_higdata err! [ 1.537557] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0 [ 1.544465] sunxi-rtc rtc: RTC enabled [ 1.549332] i2c /dev entries driver [ 1.554027] usbcore: registered new interface driver uvcvideo [ 1.560721] USB Video Class driver (1.1.1) [ 1.565334] sunxi cedar version 0.1 [ 1.569436] VE: install start!!! [ 1.569436] [ 1.574894] cedar_ve: cedar-ve the get irq is 291 [ 1.580427] VE: line 1811 set the sram data [ 1.580427] [ 1.587426] VE: ve_debug_proc_info:c05df658, data:c365c000, lock:c05df6e0 [ 1.587426] [ 1.596956] VE: install end!!! [ 1.596956] [ 1.602466] google_vp9: sunxi google vp9 version 0.1 [ 1.609363] sunxi-wdt 30090a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.620122] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0 [ 1.629860] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0 [ 1.639289] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:uart0 [ 1.648675] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0 [ 1.658019] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:uart0 [ 1.667354] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0 [ 1.677020] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.36 2019-11-26 20:26) [ 1.685998] sunxi-mmc sdc0: ***ctl-spec-caps*** 8 [ 1.691362] sunxi-mmc sdc0: No vmmc regulator found [ 1.696879] sunxi-mmc sdc0: No vqmmc regulator found [ 1.702465] sunxi-mmc sdc0: No vdmmc regulator found [ 1.708061] sunxi-mmc sdc0: No vd33sw regulator found [ 1.713744] sunxi-mmc sdc0: No vd18sw regulator found [ 1.719440] sunxi-mmc sdc0: No vq33sw regulator found [ 1.725123] sunxi-mmc sdc0: No vq18sw regulator found [ 1.731384] sunxi-mmc sdc0: set host busy [ 1.736020] sunxi-mmc sdc0: Got CD GPIO [ 1.740451] sunxi-mmc sdc0: min-frequency:100000 [ 1.746035] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.005497] sunxi-mmc sdc0: no vqmmc,Check if there is regulator [ 2.035434] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.075616] sunxi-mmc sdc0: detmode:gpio irq [ 2.075650] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.082587] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.105610] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.116734] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.36 2019-11-26 20:26) [ 2.116882] sunxi-mmc sdc1: No vmmc regulator found [ 2.116888] sunxi-mmc sdc1: No vqmmc regulator found [ 2.116893] sunxi-mmc sdc1: No vdmmc regulator found [ 2.116899] sunxi-mmc sdc1: No vd33sw regulator found [ 2.116905] sunxi-mmc sdc1: No vd18sw regulator found [ 2.116910] sunxi-mmc sdc1: No vq33sw regulator found [ 2.116915] sunxi-mmc sdc1: No vq18sw regulator found [ 2.116930] sunxi-mmc sdc1: Cann't get uart0 pinstate,check if needed [ 2.117403] sunxi-mmc sdc1: set host busy [ 2.117467] mmc:failed to get gpios [ 2.117814] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.117849] sunxi-mmc sdc1: no vqmmc,Check if there is regulator [ 2.149390] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.178385] sunxi-mmc sdc1: detmode:manually by software [ 2.222756] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !! [ 2.229176] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.239988] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !! [ 2.240057] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.242554] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.250071] sunxi-mmc sdc1: smc 1 p1 err, cmd 8, RTO !! [ 2.261375] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !! [ 2.262257] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !! [ 2.262312] usbcore: registered new interface driver usbhid [ 2.262314] usbhid: USB HID core driver [ 2.262616] mostcore: init() [ 2.264282] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !! [ 2.265160] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !! [ 2.265359] digital_vol:0, lineout_vol:31, main_gain:23, pa_msleep:160, pa_level:1 [ 2.265369] adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:1, dachpf:0 [ 2.265625] sunxi-internal-codec codec: [sunxi_internal_codec_probe] codec probe finished. [ 2.266021] sunxi-mmc sdc1: smc 1 p1 err, cmd 55, RTO !! [ 2.266466] [sunxi_card_init] card init finished. [ 2.266888] sunxi-mmc sdc1: smc 1 p1 err, cmd 55, RTO !! [ 2.267108] sunxi-codec-machine sndcodec: sun8iw19codec <-> codec mapping ok [ 2.267743] sunxi-mmc sdc1: smc 1 p1 err, cmd 55, RTO !! [ 2.268587] sunxi-mmc sdc1: smc 1 p1 err, cmd 55, RTO !! [ 2.268623] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.269560] sunxi-mmc sdc1: smc 1 p1 err, cmd 1, RTO !! [ 2.269585] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.424531] sunxi-codec-machine sndcodec: [sunxi_card_dev_probe] register card finished. [ 2.425187] NET: Registered protocol family 17 [ 2.425256] NET: Registered protocol family 15 [ 2.426197] Registering SWP/SWPB emulation handler [ 2.523488] get det_vbus is fail, 84 [ 2.527609] get id is fail, 84 [ 2.532026] sunxi-rtc rtc: setting system clock to 1970-01-01 00:00:03 UTC (3) [ 2.541546] ALSA device list: [ 2.544892] #0: sun8iw19-codec [ 2.549004] Waiting for root device /dev/mmcblk0p4... [ 2.617412] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.627755] sunxi-mmc sdc0: no vqmmc,Check if there is regulator [ 2.655430] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.674575] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.684276] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 4 timing LEGACY(SDR12) dt B [ 2.698434] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 4 timing UHS-SDR104 dt B [ 2.708988] sunxi-mmc sdc0: sdc set ios:clk 150000000Hz bm PP pm ON vdd 21 width 4 timing UHS-SDR104 dt B [ 2.719917] mmc0: new ultra high speed SDR104 SDHC card at address aaaa [ 2.728333] mmcblk0: mmc0:aaaa SD32G 29.7 GiB [ 2.735892] mmcblk0: p1 p2 p3 p4 p5 p6 [ 2.789622] VFS: Mounted root (squashfs filesystem) readonly on device 179:4. [ 2.799937] devtmpfs: mounted [ 2.803546] Freeing unused kernel memory: 140K [ 2.808629] This architecture does not have kernel memory protection. mount: mounting none on /dev failed: Resource busy mount: mounting pstore on /sys/fs/pstore failed: No such file or directory [ 3.380057] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) starting pid 712, tty '': '/etc/preinit' can't run '/etc/preinit': No such file or directory starting pid 713, tty '': '/bin/mount -t proc proc /proc' mount: mounting proc on /proc failed: Resource busy starting pid 714, tty '': '/bin/mount -t tmpfs tmpfs /run' starting pid 715, tty '': '/bin/mount -o remount,rw /' starting pid 716, tty '': '/bin/mkdir -p /dev/pts' starting pid 717, tty '': '/bin/mkdir -p /dev/shm' starting pid 718, tty '': '/bin/mount -a' starting pid 719, tty '': '/bin/hostname -F /etc/hostname' can't run '/bin/hostname': No such file or directory starting pid 720, tty '': '/etc/init.d/rcS boot' ------run rc.preboot file----- /etc/init.d/rcS: line 117: /bin/hostname: not found [ 3.566982] random: fast init done [ 3.572024] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) /etc/init.d/rcS: line 119: /sbin/mdev: not found ------run rc.modules file----- ------run rc.final file----- Load mpp modules insmod: can't insert '/lib/modules/4.9.118/videobuf2-core.ko': No such file or directory insmod: can't insert '/lib/modules/4.9.118/videobuf2-memops.ko': No such file or directory insmod: can't insert '/lib/modules/4.9.118/videobuf2-v4l2.ko': No such file or directory[ 3.627318] [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 3.639139] [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 3.648996] [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 3.685269] [VIN_ERR]registering imx307_mipi, No such device! insmod: can't insert '/lib/modules/4.9.118/sunxi_aio.ko': No such file or directory insmod: can't insert '/lib/modules/4.9.118/sunxi_ise.ko': No such file or directory Starting logging: start-stop-daemon: unrecognized option: exec start-stop-daemon: unrecognized option: exec OK Populating /dev using udev: [ 3.753468] udevd[769]: starting version 3.2 [ 3.759128] random: udevd: uninitialized urandom read (16 bytes read) [ 3.766731] random: udevd: uninitialized urandom read (16 bytes read) [ 3.774092] random: udevd: uninitialized urandom read (16 bytes read) [ 3.806475] udevd[769]: specified group 'tty' unknown [ 3.812650] udevd[769]: specified group 'dialout' unknown [ 3.819128] udevd[769]: specified group 'kmem' unknown [ 3.825129] udevd[769]: specified group 'input' unknown [ 3.831343] udevd[769]: specified group 'video' unknown [ 3.837782] udevd[769]: specified group 'lp' unknown [ 3.843653] udevd[769]: specified group 'disk' unknown [ 3.849748] udevd[769]: specified group 'cdrom' unknown [ 3.856012] udevd[769]: specified group 'tape' unknown [ 3.871398] udevd[770]: starting eudev-3.2 [ 3.886096] udevd: 2 output lines suppressed due to ratelimiting done mkdir: can't create directory '/dev/pts': File exists mkdir: can't create directory '/dev/shm': File exists Initializing random number generator... done. Starting network: /etc/init.d/S40network: line 31: /sbin/ifup: not found FAIL ifconfig: invalid hw-addr 00: Starting telnetd: udhcpc: SIOCGIFINDEX: No such device OK enable android usb insmod: can't insert '/lib/modules/4.9.118/sunxi_usb_udc.ko': No such file or directory insmod: can't insert '/lib/modules/4.9.118/sunxi_usbc.ko': No such file or directory [ 4.148637] file system registered [ 4.159977] Mass Storage Function, version: 2009/09/11 [ 4.165982] LUN: removable file: (no medium) [ 4.203640] read descriptors [ 4.207035] read strings sh: write error: Resource busy starting pid 833, tty '/dev/console': '-/bin/sh' BusyBox v1.27.2 () built-in shell (ash) ------run profile file----- _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 5C1C9C53) ---------------------------------------------- -
@tianyun923 原理图如下，请大神帮忙看看了
-
@tianyun923 i2c地址错了
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号