v821切换到spi nand flash(XT26G01CWSIG) 系统无法启动

[QY157]

日志如下：

[0]HELLO! BOOT0 is starting!
[0]BOOT0 commit : 
[0]set pll start
[1]set pll end
[1]reset_src: rtc wdg rst
[2]reset_src: det rst
[2]reset_src: pwron rst
[3]board init ok: use hosc 40M
[4]mode:0x1 sample delay:0xf
[4]OperationOpt:7 
[4]spinand quad mode error
[4]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[5]BOOT_PARAM_OFFSET:0x500000 
[6]boot param - magic error
[6]DRAM use internal ZQ!!
[7]ZQ value = 0x30
[7]DRAM BOOT DRIVE INFO: V1.02
[7]DRAM CLK = 520 MHz
[7]DRAM Type = 2 (2:DDR2,3:DDR3)
[7]DRAMC read ODT off.
[8]DRAM ODT off.
[8]ddr_clk0 = 1040 MHz
[9]trefi: 7.8us
[9]DRAM Size = 64 MB
[11]DRAM simple test OK.
[11]dram size =64
[11]mode:0x1 sample delay:0xf
[11]OperationOpt:7 
[11]spinand quad mode error
[12]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[12]mode:0x1 sample delay:0xf
[12]OperationOpt:7 
[13]spinand quad mode error
[13]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[13]block from 8 to 32
[141]Check is correct. Find a good uboot copy at block 8
[142]dma 0x2009c7c int is not used yet
[142]dma 0x2009c7c int is free, you do not need to free it again
[142]Entry_name        = opensbi
[143]Entry_name        = u-boot
[145]Entry_name        = melis-elf
[148]Jump to OpenSBI: opensbi_base = 0x80fc0000, dtb_base = 0x0, uboot_base = 0x82000000

OpenSBI 92310c8ed361641fa38c20bd0073be189e0f1282
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

init msb region pma attribute
Platform Name             : sun300iw1
Platform Features         : medeleg
Platform HART Count       : 1
Platform IPI Device       : sunxi_plicsw
Platform Timer Device     : sunxi_plmt @ 40000000Hz
Platform Console Device   : sunxi_uart
Platform HSM Device       : ---
Platform PMU Device       : ---
Platform Reboot Device    : sunxi_wdt
Platform Shutdown Device  : sunxi_wdt
Firmware Base             : 0x80fc0400
Firmware Size             : 75 KB
Runtime SBI Version       : 0.3

Domain0 Name              : root
Domain0 Boot HART         : 0
Domain0 HARTs             : 0*
Domain0 Region00          : 0x80fc0000-0x80fdffff ()
Domain0 Region01          : 0x00000000-0xffffffff (R,W,X)
Domain0 Next Address      : 0x82000000
Domain0 Next Arg1         : 0x00000000
Domain0 Next Mode         : S-mode
Domain0 SysReset          : yes

Boot HART ID              : 0
Boot HART Domain          : root
Boot HART ISA             : rv32imafdcnsux
Boot HART Features        : scounteren,mcounteren,mcountinhibit,sscofpmf
Boot HART PMP Count       : 64
Boot HART PMP Granularity : 8
Boot HART PMP Address Bits: 31
Boot HART MHPM Count      : 4
Boot HART MIDELEG         : 0x00000222
Boot HART MEDELEG         : 0x0000b109


U-Boot 2018.07 (Aug 15 2025 - 10:41:44 +0800) Allwinner Technology

I2C:   ready
[00.162]DRAM:  64 MiB
[00.163]Relocation Offset is: 01f23000, reloc addr is: 83f23000
[00.165]secure enable bit: 0
[00.165]drivers/sunxi_power/pmu_axpnull.c pmu_axpnull_probe 26 axpdummy probe
FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_INTERNAL
[00.167]axp2601 pmic_bus_read fail
[00.167]BMU: AXPNULL
[00.168]CPU=960 MHz,PERI=3072 Mhz,AHB=192 Mhz, APB=96Mhz
SPI ALL:   ready
[00.170]flash init start
[00.171]workmode = 0,storage type = 0
[00.177]sunxi-spinand-phy: spinand sample_mode:1 sample_delay:f

device nand0 <nand>, # parts = 4
 #: name		size		offset		mask_flags
 0: boot0               0x00100000	0x00000000	1
 1: uboot               0x00300000	0x00100000	1
 2: secure_storage      0x00100000	0x00400000	1
 3: sys                 0x07b00000	0x00500000	0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.330]ubi0: attaching mtd4
[00.926]ubi0: scanning is finished
[00.934]ubi0: attached mtd4 (name "sys", size 123 MiB)
[00.935]ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[00.935]ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[00.936]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.936]ubi0: good PEBs: 980, bad PEBs: 4, corrupted PEBs: 0
[00.936]ubi0: user volume: 10, internal volumes: 1, max. volumes count: 128
[00.937]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[00.938]ubi0: available PEBs: 0, total reserved PEBs: 980, PEBs reserved for bad PEB handling: 16
[00.938]sunxi flash init ok
[01.194]Loading Environment from SUNXI_FLASH... OK
[01.235]usb burn from boot
delay time 0
[01.244]usb prepare ok
[01.545]overtime
[01.548]do_burn_from_boot usb : no usb exist
List file under ULI/factory
** Unrecognized filesystem type **
[01.575]update bootcmd
[01.609]change working_fdt 0x838e2ea0 to 0x838c2ea0
[01.617]## error: update_fdt_dram_para : FDT_ERR_NOTFOUND
[01.619]update dts
Info: gmac phy mode = rmii, phy_interface = 6
FDT ERROR:get muxsel err returned FDT_ERR_INTERNAL
Error: gmac set pin failed
[01.623]Board Net Initialization Failed
[01.623]No ethernet found.
Hit any key to stop autoboot:  0 
[02.238]no vendor_boot partition is found
Android's image name: sun300i_riscv32
Detect comp gzip
ERROR: reserving fdt memory region failed (addr=80ffff00 size=100)
[02.465]
Starting kernel ...

[    0.000000] Linux version 5.4.220 (yinqi@yinqi) (gcc version 10.4.0 (2024-02-02_nds32le-linux-glibc-v5d-bbc31ec98)) #2 PREEMPT Fri Aug 15 10:48:09 CST 2025
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000083c00000, size 4 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000081200000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node vdev0buffer@81200000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000081646000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node e907_rpbuf@81646000, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000080000000-0x0000000083ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000080ffefff]
[    0.000000]   node   0: [mem 0x0000000081244000-0x0000000081643fff]
[    0.000000]   node   0: [mem 0x000000008164e000-0x0000000083ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x0000000083ffffff]
[    0.000000] On node 0 totalpages: 15793
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 15793 pages, LIFO batch:3
[    0.000000] SBI specification v0.3 detected
[    0.000000] SBI implementation ID=0x1 Version=0x10000
[    0.000000] SBI v0.2 TIME extension detected
[    0.000000] SBI v0.2 IPI extension detected
[    0.000000] SBI v0.2 RFENCE extension detected
[    0.000000] SBI SRST extension detected
[    0.000000] riscv: base ISA extensions acdfim
[    0.000000] riscv: ELF capabilities acdfim
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 15665
[    0.000000] Kernel command line: ubi.mtd=sys ubi.block=0,rootfs earlyprintk=sunxi-uart,0x42500000 initcall_debug=0 console=ttyS0,1500000 loglevel=8 root=/dev/ubiblock0_7 rootwait rootfstype=squashfs init=/init rdinit=/rdinit partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:private@ubi0_5:riscv0@ubi0_6:rootfs@ubi0_7:rootfs_data@ubi0_8:UDISK@ubi0_9: cma=1M snum=7c000c71a300c822250 mac_addr= wifi_mac=60:c2:2a:12:48:6f bt_mac= selinux=0 specialstr= gpt=1 arm-smmu-v3.disable_bypass=0 androidboot.serialno=7c000c71a300c822250 androidboot.hardware=sun300iw1p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.07(08/15/2025-10:41:44) mbr_offset=1032192 bootreason=button aw-ubi-spinand.ubootblks=24 androidboot.dramfreq=520 androidboot.dramsize=64 mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) uboot_backup=ubootA 
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Sorting __ex_table...
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 27108K/63172K available (5310K kernel code, 432K rwdata, 2008K rodata, 168K init, 345K bss, 31968K reserved, 4096K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] NR_IRQS: 72, nr_irqs: 72, preallocated irqs: 0
[    0.000000] plic: mapped 187 interrupts with 1 handlers for 2 contexts.
[    0.000000] sunxi:ccu-ng:[INFO]: Current HOSC rate is 40000000HZ
[    0.000000] AW BSP version: UNKNOWN, 2025-08-15 10:48:03
[    0.000000] sunxi:ccu-ng:[INFO]: aon_ccu: sunxi ccu init OK
[    0.000000] sunxi:ccu-ng:[INFO]: sunxi ccu common driver version: 1.2.4
[    0.000000] sunxi:ccu-ng:[INFO]: ccu: sunxi ccu init OK
[    0.000000] sunxi:ccu-ng:[INFO]: sunxi app ccu driver version: 0.7.2
[    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x939a85c40, max_idle_ns: 440795202120 ns
[    0.000011] sched_clock: 64 bits at 40MHz, resolution 25ns, wraps every 4398046511100ns
[    0.001079] Console: colour dummy device 80x25
[    0.001158] Calibrating delay loop (skipped), value calculated using timer frequency.. 80.00 BogoMIPS (lpj=160000)
[    0.001799] pid_max: default: 32768 minimum: 301
[    0.002388] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.002723] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005662] rcu: Hierarchical SRCU implementation.
[    0.011077] devtmpfs: initialized
[    0.032057] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.032410] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.033279] pinctrl core: initialized pinctrl subsystem
[    0.041638] phys:80000000 low vir:c0000000 non-cache:dfc80000~e3c80000
[    0.042819] NET: Registered protocol family 16
[    0.048151] sunxi:ccu-ng:[INFO]: sunxi prcm ccu driver version: 0.0.4
[    0.056385] sunxi:pin-42000000.pinctrl:[INFO]: pinctrl withstand voltage config mode=auto_hard
[    0.056634] sunxi:pin:[INFO]: sunxi pinctrl core driver version: 1.4.8
[    0.057827] sunxi:pin:[INFO]: sunxi rtc-pinctrl version: 0.0.2
[    0.060225] sunxi:pin-42000540.pinctrl:[INFO]: pinctrl withstand voltage config mode=auto_hard
[    0.064663] sunxi hwspinlock vbase:0x(ptrval)
[    0.094655] SCSI subsystem initialized
[    0.095049] usbcore: registered new interface driver usbfs
[    0.095159] usbcore: registered new interface driver hub
[    0.095544] usbcore: registered new device driver usb
[    0.095997] mc: Linux media interface: v0.10
[    0.096236] videodev: Linux video capture interface: v2.00
[    0.097469] Advanced Linux Sound Architecture Driver Initialized.
[    0.103063] sun6i-dma 43002000.dma-controller: sunxi dma probed, driver version: 1.2.11
[    0.105049] sunxi-soc-regulator 4a000800.soc_pmu0: Supply for ldo1 (ldo1) resolved to itself
[    0.105290] ldo1: supplied by regulator-dummy
[    0.106476] ion_size_pool heap_size_pool@0: no small_source configurated, use cma as default
[    0.108467] sunxi:pin-42000000.pinctrl:[INFO]: Auto power withstand voltage configuration detected, automatically exit!
[    0.109089] sunxi-twi 42502000.twi0: 42502000.twi0 supply twi not found, using dummy regulator
[    0.110457] sunxi:twi-42502000.twi0:[INFO]: v2.7.9 probe success
[    0.111516] sunxi:pwm-42000c00.pwm:[INFO]: start probe
[    0.112199] sunxi:pwm-42000c00.pwm:[INFO]: pwmchip probe success
[    0.114694] clocksource: Switched to clocksource riscv_clocksource
[    0.119503] thermal_sys: Registered thermal governor 'fair_share'
[    0.119512] thermal_sys: Registered thermal governor 'bang_bang'
[    0.119568] thermal_sys: Registered thermal governor 'step_wise'
[    0.120057] thermal_sys: Registered thermal governor 'user_space'
[    0.120486] thermal_sys: Registered thermal governor 'power_allocator'
[    0.121571] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.123059] sunxi_usb_udc 44100000.udc-controller: sunxi:sunxi_usb_udc UDC Inner DMA Feature - wordaddr: -1, extend: disabled
[    0.124488] NET: Registered protocol family 2
[    0.124847] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.126023] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.126286] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.126967] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.127389] TCP: Hash tables configured (established 1024 bind 1024)
[    0.128035] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.128379] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.129190] NET: Registered protocol family 1
[    0.130036] RPC: Registered named UNIX socket transport module.
[    0.130079] RPC: Registered udp transport module.
[    0.130438] RPC: Registered tcp transport module.
[    0.130942] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.132161] sunxi:spi-44025000.spi:[INFO]: spi manual set sample type_1, mode_1, delay_15
[    0.132441] sunxi-spi-ng 44025000.spi: 44025000.spi supply spi not found, using dummy regulator
[    0.133298] sunxi:spi-44025000.spi:[INFO]: bus num_0 mode_16 freq_100000000
[    0.133573] sunxi:spi-44025000.spi:[INFO]: cs num_1 mode_1
[    0.134045] of_dma_request_slave_channel: dma-names property of node '/soc@2002000/spi@44025000' missing or empty
[    0.134926] sunxi:spi-44025000.spi:[ERR]: failed to request dma tx channel -19
[    0.135557] sunxi:spi-44025000.spi:[WARN]: clk 100000000 not support, round to nearly 78769230
[    0.136648] sunxi:spi-44025000.spi:[INFO]: probe success (Version 2.5.4)
[    0.140353] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[    0.153175] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.154617] NFS: Registering the id_resolver key type
[    0.154885] Key type id_resolver registered
[    0.154913] Key type id_legacy registered
[    0.155244] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.155757] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.156672] fuse: init (API version 7.31)
[    0.158230] NET: Registered protocol family 38
[    0.158328] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.158803] io scheduler mq-deadline registered
[    0.159071] io scheduler kyber registered
[    0.182643] loop: module loaded
[    0.183676] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.183832] ehci-platform: EHCI generic platform driver
[    0.184643] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.184758] ohci-platform: OHCI generic platform driver
[    0.186474] usbcore: registered new interface driver uas
[    0.186604] usbcore: registered new interface driver usb-storage
[    0.187135] i2c /dev entries driver
[    0.188465] usbcore: registered new interface driver usbhid
[    0.188499] usbhid: USB HID core driver
[    0.190424] uart-ng uart-ng0: uart-ng0 supply uart not found, using dummy regulator
[    0.190929] sunxi:uart-ng-uart-ng0:[INFO]: cannot get the TX DMA channel!
[    0.191121] sunxi:uart-ng-uart-ng0:[INFO]: cannot get the RX DMA channel!
[    0.191728] sunxi:uart-ng:[INFO]: sunxi uart-ng driver version: 1.1.10
[    0.192184] uart-ng0: ttyS0 at MMIO 0x42500000 (irq = 134, base_baud = 12000000) is a SUNXI
[    0.192818] sunxi:uart-ng-uart-ng0:[INFO]: console setup baud 1500000 parity n bits 8, flow n
[    0.193443] sunxi:uart-ng-uart-ng0:[INFO]: uart0, select set 6, baud 1500000, uartclk 192000000 beyond rance[24000000, 120000000]
[    0.194407] printk: console [ttyS0] enabled
[    0.194407] printk: console [ttyS0] enabled
[    0.195353] printk: bootconsole [earlycon0] disabled
[    0.195353] printk: bootconsole [earlycon0] disabled
[    0.197491] sunxi:rtc-4a000c00.rtc:[WARN]: Fail to get clock 'rtc-1k'
[    0.198340] sunxi:rtc-4a000c00.rtc:[WARN]: Fail to get clock 'rtc-spi'
[    0.199297] sunxi:rtc:[INFO]:  Saving SoC boot-reason: COLD-BOOT
[    0.200052] sunxi:rtc-4a000c00.rtc:[INFO]: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[    0.201334] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.202587] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.204182] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.205429] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.206657] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.208574] sunxi-rtc 4a000c00.rtc: registered as rtc0
[    0.209276] sunxi:rtc_sun300iw1_frun_counter:[ERR]: rtc_frun_counter_init(83): rtc frun counter src not from extern32k osc
[    0.210620] sunxi:rtc-4a000c00.rtc:[WARN]: clocksource not work: rtc free running counter
[    0.211673] sunxi:rtc-4a000c00.rtc:[INFO]: sunxi rtc probed
[    0.214209] sunxi-wdt 4a001000.watchdog: Watchdog enabled (timeout=300 sec, nowayout=0), driver version: 1.0.5
[    0.217946] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: SD/MMC/SDIO Host Controller Driver(v5.55 2024-08-26 15:32)
[    0.219496] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: ctl-spec-caps 8
[    0.220385] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vmmc regulator found
[    0.221294] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vqmmc regulator found
[    0.222196] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vdmmc regulator found
[    0.223120] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vd33sw regulator found
[    0.224027] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vd18sw regulator found
[    0.224935] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vq33sw regulator found
[    0.225847] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: No vq18sw regulator found
[    0.226781] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: manual set ocr
[    0.227585] sunxi:sunxi_mmc_host-44020000.sdmmc:[WARN]: Cann't get pin bias hs pinstate,check if needed
[    0.228831] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: Could not get store clock
[    0.229760] sunxi:sunxi_mmc_host-44020000.sdmmc:[ERR]: Could not get msi_lite clock
[    0.231262] sunxi-mmc 44020000.sdmmc: Got CD GPIO
[    0.231985] sunxi-mmc 44020000.sdmmc: sunxi:sunxi_mmc_hostcd-set-debounce is missing, function is no used
[    0.233806] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.247734] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.262047] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: detmode:gpio irq
[    0.265212] sunxi:g2d_sunxi:[INFO]: [G2D]: rcq version initialized.major:245
[    0.266098] sunxi:g2d_sunxi:[INFO]: [G2D]: g2d_module_init
[    0.267974] sunxi:gpadc:[INFO]: sunxi_gpadc_init(): 2148: gpadc class register success
[    0.269444] sunxi:gpadc-42009000.gpadc0:[WARN]: warn: sample rate not set
[    0.270781] input: sunxi-gpadc0/channel0/input0 as /devices/platform/soc@2002000/42009000.gpadc0/input/input0
[    0.272603] input: sunxi-gpadc0/channel1/input0 as /devices/platform/soc@2002000/42009000.gpadc0/input/input1
[    0.274629] sunxi:gpadc-42009000.gpadc0:[INFO]: sunxi_gpadc probe success
[    0.281842] sunxi-msgbox 43033000.msgbox: sunxi:sunxi_msgboxsunxi_msgbox_probe(): sunxi msgbox start probe
[    0.283401] sunxi-msgbox 43033000.msgbox: sunxi:sunxi_msgboxsunxi_msgbox_probe(): sunxi msgbox probe success
[    0.285972] sunxi-rproc 43030000.e907_rproc: sunxi rproc driver 2.4.3
[    0.287102] sunxi-rproc 43030000.e907_rproc: rv-cfg base: 0x43030000, va: 0xdfc43000
[    0.288137] sunxi-rproc 43030000.e907_rproc: find rproc standby error
[    0.289201] sunxi-rproc 43030000.e907_rproc: timeout_ms: 6000
[    0.289932] sunxi-rproc 43030000.e907_rproc: reset_type: 2
[    0.290599] sunxi-rproc 43030000.e907_rproc: reg:        43031000
[    0.291480] sunxi-rproc 43030000.e907_rproc: irq_num:    163
[    0.292191] sunxi-rproc 43030000.e907_rproc: panic_on_timeout: 1
[    0.293223] sunxi-rproc 43030000.e907_rproc: The bootloader doesn't boot up the remoteproc when auto-boot is enabled!
[    0.294531] sunxi-rproc 43030000.e907_rproc: is_using_kernel_fw: 0
[    0.295479] remoteproc remoteproc0: e907_rproc is available
[    0.296342] sunxi-rproc 43030000.e907_rproc: sunxi rproc driver probe ok
[    0.297988] sunxi-rpbuf-controller rpbuf_controller0@0: assigned reserved memory node e907_rpbuf@81646000
[    0.300077] [ADDR_MGT] addr_mgt_probe: module version: v1.0.13
[    0.301347] [ADDR_MGT] addr_mgt_probe: success.
[    0.302458] NET: Registered protocol family 17
[    0.303118] NET: Registered protocol family 15
[    0.303803] Key type dns_resolver registered
[    0.327081] UBI error: cannot open mtd sys, error -2
[    0.327732] UBI: block: can't open volume on ubi0_-1, err=-19
[    0.328437] sunxi:rtc-4a000c00.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    0.329755] sunxi-rtc 4a000c00.rtc: setting system clock to 1970-01-01T00:00:02 UTC (2)
[    0.333265] sunxi:disp:[WARN]: [DE]: not found boot_disp0
[    0.334000] sunxi:disp:[WARN]: [DE]: sel 0, gamma_base=0xe4130040
[    0.334875] sunxi:disp:[WARN]: [DE]: sel 0, gamma_ctrl_block 0xe4130040 val c352a000 dirty 0 size 8 gamma_tab_block 0xe4130100 val c352a0c0 dirty 0 size 1024
[    0.337464] sunxi:disp:[ERR]: [FB]: fb_num 1 fb_format 0
[    0.338175] sunxi:disp:[ERR]: [FB]: fbinfo: fb: 0, disp: 0 channel: 0 layer: 0 zorder: 16 w: 320 h: 192
[    0.339649] sunxi:disp:[ERR]: [FB]: fb_num 0 use rot 0 degree0
[    0.340394] sunxi:disp:[ERR]: [FB]: smooth display disp0: type64 mode4 disp1: type0 mode0
[    0.343303] sunxi:disp:[ERR]: [FB]: display logo on display 0 channel 0 layer 0 type 0
[    0.344407] sunxi:disp:[ERR]: [FB]: fb 0 vir 0x(ptrval) phy 0x83c80000
[    0.345222] sunxi:disp:[ERR]: [FB]: platform_fb_post_init start
[    0.346303] sunxi:disp:[WARN]: [DE]: attached ok, mgr0<-->dev0
[    0.347098] sunxi:disp:[WARN]: [DE]: type:64,mode:4,fmt:rgb,bits:8bits,eotf:0,cs:0 dvi_hdmi:2, range:0 scan:0 ratio:8
[    0.349612] sunxi:sound-common:[ERR]: 301 pacfg_level_trig_init(): pa-pin-0 (79) request failed
[    0.350769] sunxi:sound-common:[ERR]: 612 snd_sunxi_pa_pin_init(): pacfg_level_trig_init failed
[    0.353290] sunxi:sound-i2s:[WARN]: 2206 snd_sunxi_dts_params_init(): clk-en-post-delay missing
[    0.354388] sunxi:sound-i2s:[WARN]: 2214 snd_sunxi_dts_params_init(): clk-keep missing
[    0.356164] sunxi:sound-mach:[WARN]: 372 asoc_simple_parse_ucfmt(): set data late to default
[    0.357653] debugfs: Directory 'soc@2002000:codec_plat' with parent 'audiocodec' already present!
[    0.359023] sunxi-snd-mach soc@2002000:codec_mach: 42030000.codec <-> soc@2002000:codec_plat mapping ok
[    0.361686] sunxi:sound-mach:[WARN]: 372 asoc_simple_parse_ucfmt(): set data late to default
[    0.362839] sunxi-snd-mach soc@2002000:i2s0_mach: No 'sound-dai' property
[    0.364009] debugfs: Directory '42032000.i2s0_plat' with parent 'sndi2s0' already present!
[    0.365273] sunxi-snd-mach soc@2002000:i2s0_mach: snd-soc-dummy-dai <-> 42032000.i2s0_plat mapping ok
[    0.372382] ALSA device list:
[    0.372797]   #0: audiocodec
[    0.373151]   #1: sndi2s0
[    0.373742] sunxi:uart-ng-uart-ng0:[INFO]: uart0, select set 6, baud 1500000, uartclk 192000000 beyond rance[24000000, 120000000]
[    0.375365] Waiting for root device /dev/ubiblock0_7...
[    0.462775] sunxi:sunxi_mmc_host-44020000.sdmmc:[INFO]: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    0.464227] sunxi:pin-42000000.pinctrl:[INFO]: Auto power withstand voltage configuration detected, automatically exit!
[    1.378907] sunxi_usb_udc 44100000.udc-controller: 44100000.udc-controller supply udc not found, using dummy regulator

[awwwwa]

使用quick_config 配置的吗