安装全志USB驱动那些事

柚木鉉 LV 9

Windows10有一点奇怪，他会自己从网络上安装驱动。这本来没什么坏处，但是对于全志的驱动，他会自动安装成其他设备使用的驱动，导致驱动不匹配。使用驱动安装器安装后虽然有官方驱动但是不是首选驱动。所以要手动更换驱动。

找到资源管理器里的USB Device(VID_1f3a_PID_efe8)，如果没见到就是板子没进入FEL模式。
右键，更新驱动程序
浏览我的电脑查找
让我从计算机上的可用驱动列表中选取
从磁盘安装
浏览
选择 AW_Driver 里的usbdrv.inf 文件
确定
下一页
安装完成，关闭窗口
然后就可以烧写固件了

mxlol233 LV 3

@yuzukitsuru

大佬，win11下安装不了。

whycan晕哥 LV 9

@mxlol233
进安全模式安装？

mxlol233 LV 3

@whycan 嗯，也是个办法。
我最后是在一个低版本的win10虚拟机里搞的。

t1290 LV 4

显示设备无法启动怎么办。win10，全志官网下的usb驱动包

whycan晕哥 LV 9

@t1290 在安装全志USB驱动那些事中说：

显示设备无法启动怎么办。win10，全志官网下的usb驱动包

截图看看。

t1290 LV 4

@whycan %RR73QL6J(}MTMQ{K(DX99S.png 这个样子

whycan晕哥 LV 9

@t1290

进入安全模式安装驱动试一试：

https://zhuanlan.zhihu.com/p/458838139 （仅供参考）

t1290 LV 4

@whycan 还是上面那样

whycan晕哥 LV 9

@t1290
那换台电脑试一试。

jysrfeng LV 1

@yuzukitsuru 安装是安装上了，不过一直都提示找到新硬件安了好多遍一直提示每次都能安装成功每次安装完又出来提示
郁闷

summerlotus LV 2

我也是一样 win11，死活驱动打不上啊

怎么破~

whycan晕哥 LV 9

@summerlotus
那个地方就是叹号，不用管他。

summerlotus LV 2

@whycan 但是识别不到设备，属性页显示是设别无法启动，代码10

rainnnn LV 2

更新驱动后，这里还是显示无设备连接，设备识别出的还是USB device(VID_1F3A PID_EFE8)，正常来说应该是Tina ADB

fanzhe LV 3

@whycan 晕哥，用phoenixsuit烧写，怎么起不来了，之前还正常呢，用了下zadig后，用phoenixsuit烧写就进fel起不来

sbi reboot
[53]HELLO! BOOT0 is starting!
[56]BOOT0 commit : 88480af
[59]set pll start
[61]periph0 has been enabled
[64]set pll end
[65][pmu]: bus read error
[67]board init ok
[69]get_pmu_exist() = -1
[71]DRAM BOOT DRIVE INFO: V0.33
[74]DRAM CLK = 792 MHz
[76]DRAM Type = 3 (2:DDR2,3:DDR3)
[80]DRAMC ZQ value: 0x7b7bfb
[82]DRAM ODT value: 0x42.
[85]ddr_efuse_type: 0x0
[88]DRAM SIZE =1024 M
[90]dram_tpr4:0x0
[91]PLL_DDR_CTRL_REG:0xf8004100
[94]DRAM_CLK_REG:0xc0000000
[97][TIMING DEBUG] MR2= 0x18
[101]DRAM simple test OK.
[103]dram size =1024
[105]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[110]block from 8 to 32
[169]Check is correct.
[171]dma 0x301a8 int is not used yet
[174]dma 0x301a8 int is free, you do not need to free it again
[180]Entry_name = opensbi
[183]Entry_name = u-boot
[187]Entry_name = dtb
[189]Jump to second Boot.

OpenSBI auto-t113-linux-V0.8-3-ge39e937

/ __ \ / | _ _ |
| | | | __ ___ _ __ | ( | |) || |
| | | | '_ \ / _ \ '_ \ ___ | _ < | |
| || | |) | __/ | | |) | |) || |
_/| ./ _|| ||/|____/|
| |
|_|

Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x41fc0400
Firmware Size : 75 KB
Runtime SBI Version : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3 : 0x0000000000020000-0x0000000000027fff (A,▒

U-Boot 2018.07-ge987def5 (Nov 07 2022 - 03:11:27 +0000) Allwinner Technology

[00.274]DRAM: 1 GiB
[00.276]Relocation Offset is: 3deea000
[00.281]secure enable bit: 0
can't support chip type 20480
[00.286]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
sunxi flash map init
SPI ALL: ready
[00.297]flash init start
[00.299]workmode = 0,storage type = 0
[00.306]sunxi-spinand-phy: spinand sample_mode:2 sample_delay:4

device nand0 <nand>, # parts = 4
#: name size offset mask_flags
0: boot0 0x00100000 0x00000000 1
1: uboot 0x00300000 0x00100000 1
2: secure_storage 0x00100000 0x00400000 1
3: sys 0x0fb00000 0x00500000 0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.641]ubi0: attaching mtd4
[00.849]ubi0: scanning is finished
[00.856]ubi0: attached mtd4 (name "sys", size 251 MiB)
[00.861]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.867]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.873]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.880]ubi0: good PEBs: 1004, bad PEBs: 0, corrupted PEBs: 0
[00.885]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[00.892]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[00.899]ubi0: available PEBs: 0, total reserved PEBs: 1004, PEBs reserved for bad PEB handling: 40
[00.908]sunxi flash init ok
[00.911]line:703 init_clocks
[00.914]drv_disp_init
request pwm success, pwm2:pwm2:0x2000c00.
[00.931]drv_disp_init finish
[01.031]Loading Environment from SUNXI_FLASH... OK
[01.052]boot_gui_init:start
[01.055]set disp.dev2_output_type fail. using defval=0
[01.082]set disp.fb0_rot_used fail. using defval=0
[01.086]set disp.fb0_rot_degree fail. using defval=0
[01.256]boot_gui_init:finish
partno erro : can't find partition bootloader
[01.273]bmp_name=bootlogo.bmp size 3072054
[01.315]LCD open finish
[01.362]out of usb burn from boot: not need burn key
[01.368]Item0 (Map) magic is bad
partno erro : can't find partition private
▒[53]HELLO! BOOT0 is starting!
[56]BOOT0 commit : 88480af
[59]set pll start
[61]periph0 has been enabled
[64]set pll end
[65][pmu]: bus read error
[67]board init ok
[69]rtc[2] value = 0x5aa5a55a
[72]eraly jump fel

leoxiaofei LV 2

Win11驱动装了无法使用。

stmshow LV 2

@mxlol233 大兄弟，请问你这个驱动整好了吗

stmshow LV 2

@summerlotus 大兄弟，请问你这个驱动整好了吗

stmshow LV 2

@rainnnn 我也是这个问题没法用呀