@jameschen 抱歉，没有
M
MasterLu 发布的帖子
-
T527 修改分辨率后显示异常发布在 T527系列-工业车载
配置成1280x800时正常
配置成1024x600时异常
可以看到，1280x800时error为1，后面没有出现err，1024x600时一直出现err
不知道是什么问题，麻烦大佬帮忙看下 -
回复: T527烧写安全固件后无法启动发布在 T527系列-工业车载
@awwwwa 烧写dragonboard固件的时候是没有烧写rotpak.bin的，当时也是无法启动，并且无法烧录非安全固件，当时没有仔细去看日志，误以为烧写rotpk.bin后可以启动，或者可以烧写非安全固件。
从日志上看是创建keystoreService时，connect keymint Service报错，而前面启动 aw keymint service的时候应该是没问题的。[ 12.928598][ T226] DEBUG: Abort message: 'Failed to create service android.system.keystore2.IKeystoreService/default because of In KeystoreService::new_native_binder: Trying to construct mandatory security level TEE. [ 12.959109][ T226] DEBUG: [ 12.962248][ T226] DEBUG: Caused by: [ 12.966371][ T226] DEBUG: 0: In KeystoreSecurityLevel::new_native_binder. [ 12.974471][ T226] DEBUG: 1: In get_keymint_device. [ 12.980423][ T226] DEBUG: 2: In connect_keymint: Trying to connect to genuine KeyMint service. [ 12.990575][ T226] DEBUG: 3: Binder transaction error NAME_NOT_FOUND.'这几行log的位置分别在 system\security\keystore2\src目录下的 security_level.rs、globals.rs、errors.rs中。
这部分代码我不太理解
-
T527烧写安全固件后无法启动发布在 T527系列-工业车载
T527 Android13 照着文档编译DragonBoard和android二合一固件，照着文档的打包命令生成了secure固件，烧录成功后无法启动，此时未烧录rotpk.bin。
接着试着烧回非安全固件，发现烧不了。
目前想要让安全固件能够启动，下面是安全固件的启动log（已经烧录rotpk.bin）：U-Boot 2018.07-g9b0fc4c-dirty (Oct 12 2023 - 18:16:20 +0800) Allwinner Technology [00.653]CPU: Allwinner Family [00.656]Model: sun55iw3 I2C: ready [00.666]DRAM: 4 GiB [00.670]Relocation Offset is: 6e6cd000 [00.708]secure enable bit: 1 [00.711]smc_tee_inform_fdt failed with: ffff000a [00.716]PMU: AXP2202 [00.719]BMU: AXP2202 [00.720][AXP2202] comm status : 0x0 = 0x20, 0x1 = 0x90 [00.725][AXP2202] onoff status: 0x20 = 0x4, 0x21 = 0x0 [00.730][AXP2202] reboot/charge status: 0xf0 = 0x0 bias_name:pc_bias bias_vol:1800 [00.747]PMU: AXP1530 [00.749]CPU=1296 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=600Mhz [00.755]gic: sec monitor mode sunxi flash map init [00.760]flash init start [00.762]workmode = 0,storage type = 2 [00.766][mmc]: mmc driver ver uboot2018:2023-07-4 16:18:00 [00.772][mmc]: SUNXI SDMMC Controller Version:0x50500 [00.796][mmc]: Best spd md: 4-HS400, freq: 4-150000000, Bus width: 8 [00.802]sunxi flash init ok [00.804]drv_disp_init [00.861]Item0 (Map) magic is bad [00.864]the secure storage item0 copy0 magic is bad [00.876]Item0 (Map) magic is bad [00.878]the secure storage item0 copy1 magic is bad [00.883]Item0 (Map) magic is bad erase secure storage failed [00.911]drv_disp_init finish [00.925]Loading Environment from SUNXI_FLASH... OK [00.931]boot_gui_init:start disp_devices_open start: 0 end: 1 dev_num: 1 actual_dev_num: 2 [00.951]boot_gui_init:finish ** Unable to read file advert.crc ** [00.957]sunxi bmp info error : unable to open logo file[00.964]LCD open finish sunxi_flash [00.968]bmp_name=bootlogo.bmp size 3072054 [01.001]Item0 (Map) magic is bad [01.004]the secure storage item0 copy0 magic is bad [01.015]Item0 (Map) magic is bad [01.018]the secure storage item0 copy1 magic is bad [01.022]Item0 (Map) magic is bad secure storage read widevine fail [01.028]secure storage read widevine fail with:-1 secure storage read ec_key fail [01.036]secure storage read ec_key fail with:-1 secure storage read hdcpkey fail [01.043]secure storage read hdcpkey fail with:-1 [01.047]usb burn from boot delay time 0 weak:otg_phy_config [01.058]usb prepare ok [01.249]usb sof ok [01.250]usb probe ok [01.252]usb setup ok set address 0x39 set address 0x39 ok [01.659]do_burn_from_boot usb : have no handshake skip update boot_param List file under ULI/factory ** Unrecognized filesystem type ** [01.675]update part info [01.691]update bootcmd [01.772]change working_fdt 0xb467ce50 to 0xb464ce50 [01.780]The storage not support sample function [01.797]update dts Hit any key to stop autoboot: 0 pubkey vbmeta_a valid CACHE: Misaligned operation at range [4fffffe0, 52c1d020] ramdisk use init boot Android's image name: arm64 [02.390]Starting kernel ... [02.392][mmc]: mmc exit start [02.410][mmc]: mmc 2 exit ok NOTICE: [SCP] :wait arisc ready.... NOTICE: [SCP] :arisc version: [toia25t-na-7iord-31d0.1v-5crhpla0v-a-69.trid] NOTICE: [SCP] :arisc startup ready NOTICE: [SCP] :arisc startup notify message feedback NOTICE: [SCP] :sunxi-arisc driver is starting BL3-1: Next image address = 0x40080000 BL3-1: Next image spsr = 0x3c5 [ 0.000000][ T0] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000][ T0] Linux version 5.15.104-aiot-t527-android13-v1.0rc5-alpha-v0.96 (lizhi@bsp2) (Android (8490178, based on r450784d) clang version 14.0.6 (https://android.googlesource.com/toolchain/llvm-project 4c603efb0cca074e9238af8b4106c30add4418f6), LLD 14.0.6) #3 SMP PREEMPT Thu Oct 12 18:18:02 CST 2023 [ 0.000000][ T0] Machine model: sun55iw3 [ 0.000000][ T0] Stack Depot is disabled [ 0.000000][ T0] KVM is not available. Ignoring kvm-arm.mode [ 0.000000][ T0] earlycon: uart8250 at MMIO32 0x0000000002500000 (options '') [ 0.000000][ T0] printk: bootconsole [uart8250] enabled [ 0.000000][ T0] efi: UEFI not found. [ 0.000000][ T0] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000][ T0] OF: reserved mem: 0x0000000000020000..0x000000000002ffff (64 KiB) nomap non-reusable dsp0iram@20000 [ 0.000000][ T0] OF: reserved mem: 0x0000000000030000..0x0000000000037fff (32 KiB) nomap non-reusable dsp0dram0@30000 [ 0.000000][ T0] OF: reserved mem: 0x0000000000038000..0x000000000003ffff (32 KiB) nomap non-reusable dsp0dram1@38000 [ 0.000000][ T0] OF: reserved mem: 0x0000000007280000..0x00000000072bffff (256 KiB) nomap non-reusable riscvsram0@7280000 [ 0.000000][ T0] OF: reserved mem: 0x00000000072c0000..0x00000000072fffff (256 KiB) nomap non-reusable riscvsram1@72c0000 [ 0.000000][ T0] OF: reserved mem: 0x0000000048000000..0x0000000048ffffff (16384 KiB) map non-reusable bl31 [ 0.000000][ T0] OF: reserved mem: 0x000000004a000000..0x000000004a9fffff (10240 KiB) nomap non-reusable dsp0ddr@4a000000 [ 0.000000][ T0] OF: reserved mem: 0x000000004ab00000..0x000000004ab0ffff (64 KiB) nomap non-reusable dsp_share_space@4ab00000 [ 0.000000][ T0] Reserved memory: created DMA memory pool at 0x000000004ac00000, size 0 MiB [ 0.000000][ T0] OF: reserved mem: initialized node vdev0buffer@4ac00000, compatible id shared-dma-pool [ 0.000000][ T0] OF: reserved mem: 0x000000004ac00000..0x000000004ac3ffff (256 KiB) nomap non-reusable vdev0buffer@4ac00000 [ 0.000000][ T0] OF: reserved mem: 0x000000004ac40000..0x000000004ac41fff (8 KiB) nomap non-reusable vdev0vring0@4ac40000 [ 0.000000][ T0] OF: reserved mem: 0x000000004ac42000..0x000000004ac43fff (8 KiB) nomap non-reusable vdev0vring1@4ac42000 [ 0.000000][ T0] Reserved memory: created DMA memory pool at 0x000000004ae00000, size 0 MiB [ 0.000000][ T0] OF: reserved mem: initialized node vdev0buffer@4ae00000, compatible id shared-dma-pool [ 0.000000][ T0] OF: reserved mem: 0x000000004ae00000..0x000000004ae3ffff (256 KiB) nomap non-reusable vdev0buffer@4ae00000 [ 0.000000][ T0] OF: reserved mem: 0x000000004ae40000..0x000000004ae41fff (8 KiB) nomap non-reusable vdev0vring0@4ae40000 [ 0.000000][ T0] OF: reserved mem: 0x000000004ae42000..0x000000004ae43fff (8 KiB) nomap non-reusable vdev0vring1@4ae42000 [ 0.000000][ T0] Reserved memory: created DMA memory pool at 0x000000004ae44000, size 0 MiB [ 0.000000][ T0] OF: reserved mem: initialized node dsp0_rpbuf@4ae44000, compatible id shared-dma-pool [ 0.000000][ T0] OF: reserved mem: 0x000000004ae44000..0x000000004ae4bfff (32 KiB) nomap non-reusable dsp0_rpbuf@4ae44000 [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] DMA32 [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000][ T0] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000040000000-0x0000000049ffffff] [ 0.000000][ T0] node 0: [mem 0x000000004a000000-0x000000004a9fffff] [ 0.000000][ T0] node 0: [mem 0x000000004aa00000-0x000000004aafffff] [ 0.000000][ T0] node 0: [mem 0x000000004ab00000-0x000000004ab0ffff] [ 0.000000][ T0] node 0: [mem 0x000000004ab10000-0x000000004abfffff] [ 0.000000][ T0] node 0: [mem 0x000000004ac00000-0x000000004ac43fff] [ 0.000000][ T0] node 0: [mem 0x000000004ac44000-0x000000004adfffff] [ 0.000000][ T0] node 0: [mem 0x000000004ae00000-0x000000004ae4bfff] [ 0.000000][ T0] node 0: [mem 0x000000004ae4c000-0x000000013fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000040000000-0x000000013fffffff] [ 0.000000][ T0] cma: Reserved 8 MiB at 0x00000000ff800000 [ 0.000000][ T0] psci: probing for conduit method from DT. [ 0.000000][ T0] psci: PSCIv1.1 detected in firmware. [ 0.000000][ T0] psci: Using standard PSCI v0.2 function IDs [ 0.000000][ T0] psci: Trusted OS migration not required [ 0.000000][ T0] psci: SMC Calling Convention v1.2 [ 0.000000][ T0] Load bootconfig: 792 bytes 50 nodes [ 0.000000][ T0] percpu: Embedded 29 pages/cpu s81688 r8192 d28904 u118784 [ 0.000000][ T0] pcpu-alloc: s81688 r8192 d28904 u118784 alloc=29*4096 [ 0.000000][ T0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000][ T0] Detected VIPT I-cache on CPU0 [ 0.000000][ T0] CPU features: SYS_ID_AA64MMFR1_EL1[11:8]: forced to 0 [ 0.000000][ T0] CPU features: detected: GIC system register CPU interface [ 0.000000][ T0] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000][ T0] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000][ T0] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009 [ 0.000000][ T0] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000][ T0] Kernel command line: stack_depot_disable=on kasan.stacktrace=off kvm-arm.mode=protected cgroup_disable=pressure rcutree.rcu_idle_gp_delay=1 cpufreq.default_governor=performance earlycon=uart8250,mmio32,0x02500000 clk_ignore_unused= initcall_debug=0 console=ttyAS0,115200 loglevel=8 root=/dev/mmcblk0p4 init=/init cma=8M snum=0167572d1080c801cd1 mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 boot_type=2 gpt=1 uboot_message=2018.07-g9b0fc4c-dirty(10/12/2023-18:16:20) disp_reserve=4096000,0xb4756000 bootreason=usb loop.max_part=4 mmcblk.perdev_minors=16 firmware_class.path=/vendor/etc/firmware bootconfig buildvariant=userdebug [ 0.000000][ T0] cgroup: Disabling pressure control group feature [ 0.000000][ T0] Unknown kernel command line parameters "snum=0167572d1080c801cd1 mac_addr= wifi_mac= bt_mac= specialstr= boot_type=2 uboot_message=2018.07-g9b0fc4c-dirty(10/12/2023-18:16:20) disp_reserve=4096000,0xb4756000 buildvariant=userdebug", will be passed to user space. [ 0.000000][ T0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000][ T0] software IO TLB: mapped [mem 0x00000000fb800000-0x00000000ff800000] (64MB) [ 0.000000][ T0] Memory: 3815384K/4194304K available (19584K kernel code, 4142K rwdata, 19848K rodata, 1472K init, 700K bss, 370728K reserved, 8192K cma-reserved) [ 0.000000][ T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU event tracing is enabled. [ 0.000000][ T0] rcu: RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=8. [ 0.000000][ T0] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000][ T0] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000][ T0] GICv3: 256 SPIs implemented [ 0.000000][ T0] GICv3: 0 Extended SPIs implemented [ 0.000000][ T0] GICv3: Distributor has no Range Selector support [ 0.000000][ T0] Root IRQ handler: gic_handle_irq.10d7cf410c142aff6d31b6303c3f9f87.cfi_jt [ 0.000000][ T0] GICv3: 16 PPIs implemented [ 0.000000][ T0] GICv3: CPU0: found redistributor 0 region 0:0x0000000003460000 [ 0.000000][ T0] ITS: No ITS available, not enabling LPIs [ 0.000000][ T0] rcu: Offload RCU callbacks from CPUs: (none). [ 0.000000][ T0] kfence: initialized - using 524288 bytes for 63 objects at 0x(____ptrval____)-0x(____ptrval____) [ 0.000000][ T0] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000][ T0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000][ T0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.010605][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.022644][ T0] pid_max: default: 32768 minimum: 301 [ 0.028720][ T0] LSM: Security Framework initializing [ 0.034621][ T0] SELinux: Initializing. [ 0.039086][ T0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.047984][ T0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.059823][ T1] rcu: Hierarchical SRCU implementation. [ 0.067328][ T1] EFI services will not be available. [ 0.073708][ T1] smp: Bringing up secondary CPUs ... [ 0.079746][ T0] Detected VIPT I-cache on CPU1 [ 0.079781][ T0] GICv3: CPU1: found redistributor 100 region 0:0x0000000003480000 [ 0.079822][ T0] CPU1: Booted secondary processor 0x0000000100 [0x412fd050] [ 0.080643][ T0] Detected VIPT I-cache on CPU2 [ 0.080673][ T0] GICv3: CPU2: found redistributor 200 region 0:0x00000000034a0000 [ 0.080707][ T0] CPU2: Booted secondary processor 0x0000000200 [0x412fd050] [ 0.081537][ T0] Detected VIPT I-cache on CPU3 [ 0.081563][ T0] GICv3: CPU3: found redistributor 300 region 0:0x00000000034c0000 [ 0.081592][ T0] CPU3: Booted secondary processor 0x0000000300 [0x412fd050] [ 0.082366][ T0] Detected VIPT I-cache on CPU4 [ 0.082395][ T0] GICv3: CPU4: found redistributor 400 region 0:0x00000000034e0000 [ 0.082426][ T0] CPU4: Booted secondary processor 0x0000000400 [0x412fd050] [ 0.083248][ T0] Detected VIPT I-cache on CPU5 [ 0.083277][ T0] GICv3: CPU5: found redistributor 500 region 0:0x0000000003500000 [ 0.083307][ T0] CPU5: Booted secondary processor 0x0000000500 [0x412fd050] [ 0.084116][ T0] Detected VIPT I-cache on CPU6 [ 0.084144][ T0] GICv3: CPU6: found redistributor 600 region 0:0x0000000003520000 [ 0.084171][ T0] CPU6: Booted secondary processor 0x0000000600 [0x412fd050] [ 0.084929][ T0] Detected VIPT I-cache on CPU7 [ 0.084957][ T0] GICv3: CPU7: found redistributor 700 region 0:0x0000000003540000 [ 0.084985][ T0] CPU7: Booted secondary processor 0x0000000700 [0x412fd050] [ 0.085088][ T1] smp: Brought up 1 node, 8 CPUs [ 0.239418][ T1] SMP: Total of 8 processors activated. [ 0.245342][ T1] CPU features: detected: 32-bit EL0 Support [ 0.251742][ T1] CPU features: detected: 32-bit EL1 Support [ 0.258143][ T1] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.267438][ T1] CPU features: detected: Common not Private translations [ 0.275080][ T1] CPU features: detected: CRC32 instructions [ 0.281488][ T1] CPU features: detected: RCpc load-acquire (LDAPR) [ 0.288565][ T1] CPU features: detected: LSE atomic instructions [ 0.295450][ T1] CPU features: detected: Privileged Access Never [ 0.302331][ T1] CPU features: detected: RAS Extension Support [ 0.309019][ T1] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.343693][ T1] CPU: All CPU(s) started at EL1 [ 0.349033][ T19] alternatives: patching kernel code [ 0.398420][ T1] Registered cp15_barrier emulation handler [ 0.404760][ T1] Registered setend emulation handler [ 0.410503][ T1] KASLR disabled due to lack of seed [ 0.416424][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.427927][ T1] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.436951][ T1] pinctrl core: initialized pinctrl subsystem [ 0.444954][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.455122][ T1] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.463869][ T1] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.473401][ T1] audit: initializing netlink subsys (disabled) [ 0.480302][ T72] audit: type=2000 audit(0.316:1): state=initialized audit_enabled=0 res=1 [ 0.480928][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.489580][ T1] thermal_sys: Registered thermal governor 'user_space' [ 0.496941][ T1] thermal_sys: Registered thermal governor 'power_allocator' [ 0.505217][ T1] cpuidle: using governor menu [ 0.518659][ T1] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.527109][ T1] ASID allocator initialised with 32768 entries [ 0.533980][ T1] Serial: AMBA PL011 UART driver [ 0.563293][ T1] AW BSP version: 8233bc4b76-dirty, 2023-09-18 11:52:47 +0800 [ 0.571439][ T1] rtc_ccu: sunxi ccu init OK [ 0.588448][ T1] clock: sunxi ccu init OK [ 0.593167][ T1] sun55iw3-cpupll 8817000.clock: Sunxi pll_cpu clk init OK [ 0.605075][ T1] ccu: sunxi ccu init OK [ 0.611146][ T1] r_ccu: sunxi ccu init OK [ 0.618297][ T1] dsp_ccu: sunxi ccu init OK [ 0.627697][ T1] sun55iw3-r-pinctrl 7022000.pinctrl: initialized sunXi PIO driver [ 0.682951][ T1] iommu: Default domain type: Translated [ 0.689094][ T1] iommu: DMA domain TLB invalidation policy: strict mode [ 0.697487][ T1] SCSI subsystem initialized [ 0.702558][ T1] usbcore: registered new interface driver usbfs [ 0.709431][ T1] usbcore: registered new interface driver hub [ 0.716061][ T1] usbcore: registered new device driver usb [ 0.722553][ T1] mc: Linux media interface: v0.10 [ 0.728034][ T1] videodev: Linux video capture interface: v2.00 [ 0.734904][ T1] pps_core: LinuxPPS API ver. 1 registered [ 0.741111][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.751914][ T1] PTP clock support registered [ 0.757018][ T1] EDAC MC: Ver: 3.0.0 [ 0.762549][ T1] Advanced Linux Sound Architecture Driver Initialized. [ 0.780321][ T1] sun6i-dma 3002000.dma-controller: sunxi dma probed [ 0.793412][ T1] sun6i-dma 7121000.dma1-controller: sunxi dma probed [ 0.801184][ T1] sunxi iommu: irq = 14 [ 0.809399][ T1] Bluetooth: Core ver 2.22 [ 0.814126][ T1] NET: Registered PF_BLUETOOTH protocol family [ 0.820723][ T1] Bluetooth: HCI device and connection manager initialized [ 0.828466][ T1] Bluetooth: HCI socket layer initialized [ 0.834587][ T1] Bluetooth: L2CAP socket layer initialized [ 0.840906][ T1] Bluetooth: SCO socket layer initialized [ 0.847226][ T1] nfc: nfc_init: NFC Core ver 0.1 [ 0.852627][ T1] NET: Registered PF_NFC protocol family [ 0.859181][ T1] sun55iw3-r-pinctrl 7022000.pinctrl: supply vcc-pl not found, using dummy regulator [ 0.869701][ T1] sunxi-twi 7081400.s_twi0: supply twi not found, using dummy regulator [ 0.879362][ T1] axp20x-i2c 6-0036: Unable to match OF ID [ 0.886983][ T1] pmu-ext-i2c 6-0036: pmu_ext_dev variant AXP1530 found [ 0.894878][ T1] axp1530-dcdc1: supplied by regulator-dummy [ 0.901869][ T1] axp1530-dcdc2: supplied by regulator-dummy [ 0.908709][ T1] axp1530-dcdc3: supplied by regulator-dummy [ 0.915640][ T1] axp1530-aldo1: supplied by regulator-dummy [ 0.922451][ T1] axp1530-dldo1: supplied by regulator-dummy [ 0.929948][ T1] pmu-ext-i2c 6-0036: pmu_ext:AXP1530 driver loaded [ 0.939279][ T1] axp20x-i2c 6-0035: AXP20x variant AXP2202 found [ 0.951772][ T1] axp2202-gpio: Failed to locate of_node [id: 0] [ 0.959003][ T1] axp2202-dcdc1: supplied by regulator-dummy [ 0.969840][ T1] axp2202-dcdc2: supplied by regulator-dummy [ 0.980649][ T1] axp2202-dcdc3: supplied by regulator-dummy [ 0.991625][ T1] axp2202-dcdc4: supplied by regulator-dummy [ 0.998456][ T1] axp2202-aldo1: supplied by regulator-dummy [ 1.005266][ T1] axp2202-aldo2: supplied by regulator-dummy [ 1.011984][ T1] axp2202-aldo3: supplied by regulator-dummy [ 1.022800][ T1] axp2202-aldo4: supplied by regulator-dummy [ 1.033615][ T1] axp2202-bldo1: supplied by regulator-dummy [ 1.044443][ T1] axp2202-bldo2: supplied by regulator-dummy [ 1.055352][ T1] axp2202-bldo3: supplied by regulator-dummy [ 1.062167][ T1] axp2202-bldo4: supplied by regulator-dummy [ 1.069006][ T1] axp2202-cldo1: supplied by regulator-dummy [ 1.075870][ T1] axp2202-cldo2: supplied by regulator-dummy [ 1.082592][ T1] axp2202-cldo3: supplied by regulator-dummy [ 1.093510][ T1] axp2202-cldo4: supplied by regulator-dummy [ 1.100076][ T1] axp2202-rtcldo: supplied by regulator-dummy [ 1.107007][ T1] axp2202-cpusldo: supplied by regulator-dummy [ 1.114177][ T1] axp2202-vmid: supplied by regulator-dummy [ 1.120734][ T1] axp2202-drivevbus: supplied by axp2202-vmid [ 1.131794][ T1] axp20x-i2c 6-0035: AXP20X driver loaded [ 1.138017][ T1] sunxi-twi 7081400.s_twi0: sunxi:twi_sunxi:v2.6.2 probe success [ 1.147321][ T1] sunxi-twi 7081800.s_twi1: sunxi:twi_sunxi:v2.6.2 probe success [ 1.157365][ T1] sunxi_pwm 2000c00.a_pwm: pwmchip probe success [ 1.164947][ T1] clocksource: Switched to clocksource arch_sys_counter [ 1.222558][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.227723][ T1] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.248713][ T1] sun55iw3-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 1.257761][ T1] NET: Registered PF_INET protocol family [ 1.264094][ T1] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 1.275497][ T1] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 1.285792][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.295146][ T1] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 1.305002][ T1] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [ 1.314208][ T1] TCP: Hash tables configured (established 32768 bind 32768) [ 1.322323][ T1] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 1.330532][ T1] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 1.339384][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.346416][ T1] NET: Registered PF_XDP protocol family [ 1.352455][ T1] PCI: CLS 0 bytes, default 64 [ 1.357765][ T8] Trying to unpack rootfs image as initramfs... [ 1.366024][ T1] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.376377][ T1] kvm [1]: HYP mode not available [ 1.383578][ T1] Initialise system trusted keyrings [ 1.389688][ T1] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.408111][ T1] fuse: init (API version 7.36) [ 1.461992][ T1] Key type asymmetric registered [ 1.467286][ T1] Asymmetric key parser 'x509' registered [ 1.473660][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 238) [ 1.482599][ T1] io scheduler mq-deadline registered [ 1.488360][ T1] io scheduler kyber registered [ 1.493778][ T1] io scheduler bfq registered [ 1.506137][ T1] reg-virt-consumer reg-virt-consumer.0.auto: DMA mask not set [ 1.514643][ T1] reg-virt-consumer reg-virt-consumer.1.auto: DMA mask not set [ 1.523040][ T1] reg-virt-consumer reg-virt-consumer.2.auto: DMA mask not set [ 1.531535][ T1] reg-virt-consumer reg-virt-consumer.3.auto: DMA mask not set [ 1.540105][ T1] reg-virt-consumer reg-virt-consumer.4.auto: DMA mask not set [ 1.548637][ T1] reg-virt-consumer reg-virt-consumer.5.auto: DMA mask not set [ 1.557192][ T1] reg-virt-consumer reg-virt-consumer.6.auto: DMA mask not set [ 1.565616][ T1] reg-virt-consumer reg-virt-consumer.7.auto: DMA mask not set [ 1.574043][ T1] reg-virt-consumer reg-virt-consumer.8.auto: DMA mask not set [ 1.582433][ T1] reg-virt-consumer reg-virt-consumer.9.auto: DMA mask not set [ 1.590943][ T1] reg-virt-consumer reg-virt-consumer.10.auto: DMA mask not set [ 1.599631][ T1] reg-virt-consumer reg-virt-consumer.11.auto: DMA mask not set [ 1.603069][ T8] Freeing initrd memory: 22076K [ 1.608230][ T1] reg-virt-consumer reg-virt-consumer.12.auto: DMA mask not set [ 1.621491][ T1] reg-virt-consumer reg-virt-consumer.13.auto: DMA mask not set [ 1.629933][ T1] reg-virt-consumer reg-virt-consumer.14.auto: DMA mask not set [ 1.638361][ T1] reg-virt-consumer reg-virt-consumer.15.auto: DMA mask not set [ 1.646851][ T1] reg-virt-consumer reg-virt-consumer.16.auto: DMA mask not set [ 1.655302][ T1] reg-virt-consumer reg-virt-consumer.17.auto: DMA mask not set [ 1.663745][ T1] reg-virt-consumer reg-virt-consumer.18.auto: DMA mask not set [ 1.672174][ T1] reg-virt-consumer reg-virt-consumer.19.auto: DMA mask not set [ 1.680659][ T1] reg-virt-consumer reg-virt-consumer.20.auto: DMA mask not set [ 1.689142][ T1] reg-virt-consumer reg-virt-consumer.21.auto: DMA mask not set [ 1.697583][ T1] reg-virt-consumer reg-virt-consumer.22.auto: DMA mask not set [ 1.709790][ T21] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.724968][ T1] brd: module loaded [ 1.744404][ T1] loop: module loaded [ 1.751178][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 1.760563][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 1.772538][ T1] MACsec IEEE 802.1AE [ 1.777384][ T1] tun: Universal TUN/TAP device driver, 1.6 [ 1.783782][ T1] CAN device driver interface [ 1.788764][ T1] PPP generic driver version 2.4.2 [ 1.794302][ T1] PPP BSD Compression module registered [ 1.800238][ T1] PPP Deflate Compression module registered [ 1.806565][ T1] PPP MPPE Compression module registered [ 1.812590][ T1] NET: Registered PF_PPPOX protocol family [ 1.818807][ T1] PPTP driver version 0.8.5 [ 1.823925][ T1] usbcore: registered new interface driver rtl8150 [ 1.830954][ T1] usbcore: registered new interface driver r8152 [ 1.837780][ T1] usbcore: registered new interface driver asix [ 1.844510][ T1] usbcore: registered new interface driver ax88179_178a [ 1.852013][ T1] usbcore: registered new interface driver cdc_ether [ 1.859237][ T1] usbcore: registered new interface driver cdc_eem [ 1.866272][ T1] usbcore: registered new interface driver cdc_ncm [ 1.873287][ T1] usbcore: registered new interface driver aqc111 [ 1.880205][ T1] usbcore: registered new interface driver r8153_ecm [ 1.888494][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.896439][ T1] ehci-pci: EHCI PCI platform driver [ 1.902124][ T1] ehci-platform: EHCI generic platform driver [ 1.909724][ T1] usbcore: registered new interface driver cdc_acm [ 1.916711][ T1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.926533][ T1] usbcore: registered new interface driver uas [ 1.933250][ T1] usbcore: registered new interface driver usb-storage [ 1.940908][ T1] usbcore: registered new interface driver xpad [ 1.947719][ T1] i2c_dev: i2c /dev entries driver [ 1.953408][ T1] usbcore: registered new interface driver uvcvideo [ 1.960493][ T1] gspca_main: v2.14.0 registered [ 1.966248][ T1] device-mapper: uevent: version 1.0.3 [ 1.972336][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 1.982747][ T1] Bluetooth: HCI UART driver ver 2.3 [ 1.988411][ T1] Bluetooth: HCI UART protocol H4 registered [ 1.994843][ T1] Bluetooth: HCI UART protocol LL registered [ 2.001374][ T1] Bluetooth: HCI UART protocol Broadcom registered [ 2.008378][ T1] Bluetooth: HCI UART protocol QCA registered [ 2.016464][ T1] mmcblk: using 16 minors per device [ 2.022142][ T1] sdhci: Secure Digital Host Controller Interface driver [ 2.029694][ T1] sdhci: Copyright(c) Pierre Ossman [ 2.035241][ T1] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.042596][ T1] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 2.050484][ T1] hid: raw HID events driver (C) Jiri Kosina [ 2.058179][ T1] usbcore: registered new interface driver usbhid [ 2.065072][ T1] usbhid: USB HID core driver [ 2.070347][ T1] ashmem: initialized [ 2.075072][ T1] gnss: GNSS driver registered with major 508 [ 2.082405][ T1] usbcore: registered new interface driver snd-usb-audio [ 2.090472][ T1] dram_clk:1200 [ 2.094133][ T1] dram_div:0x0 [ 2.099022][ T1] sun55iw3-pinctrl 2000000.pinctrl: supply vcc-pc not found, using dummy regulator [ 2.109445][ T1] sunxi-direct-gpio soc@3000000:gpio_leds: sunxi direct gpio probe success [ 2.119231][ T1] no topo process for clk path type:0 [ 2.124981][ T1] no topo process for topo type:0 [ 2.130638][ T1] [DISP]disp_module_init [ 2.135481][ T1] disp 5000000.disp: Adding to iommu group 0 [ 2.143346][ T1] disp_init_bsp_init_para not found boot_disp1 [ 2.149953][ T1] [DISP WRN]: [disp_init_drv_boot_info:2758]: smooth display screen:0 type:1 mode:4 format:0 bits:0 cs:104 eotf:4 [ 2.165244][ T1] [DISP WRN]: [gamma_init:1679]: alloc gamma[0] mm size=0x1100 [ 2.175482][ T1] [DISP WRN]: [gamma_init:1679]: alloc gamma[1] mm size=0x1100 [ 2.186006][ T1] [DISP WRN]: [de_wb_init:0779]: not support more than 1 wb at present [ 2.197010][ T1] de wrn crc 282800 [ 2.201056][ T1] [DISP WRN]: [de_gamma_get_reg_blocks:1741]: priv->reg_blk_num =4 [ 2.211674][ T1] [DISP WRN]: [de_smbl_get_reg_blocks:0224]: priv->reg_blk_num=6 [ 2.222100][ T1] [DISP WRN]: [de_gamma_get_reg_blocks:1754]: blk_num =4 [ 2.231753][ T1] [DISP WRN]: [de_smbl_get_reg_blocks:0238]: get blk_num=6, 0 [ 2.241913][ T1] de wrn crc 2a2800 [ 2.245945][ T1] [DISP WRN]: [de_gamma_get_reg_blocks:1741]: priv->reg_blk_num =4 [ 2.256550][ T1] [DISP WRN]: [de_smbl_get_reg_blocks:0224]: priv->reg_blk_num=6 [ 2.266963][ T1] [DISP WRN]: [de_wb_get_reg_blocks:0872]: not support more than 1 wb at present [ 2.278940][ T1] [DISP WRN]: [de_gamma_get_reg_blocks:1754]: blk_num =4 [ 2.288593][ T1] [DISP WRN]: [de_smbl_get_reg_blocks:0238]: get blk_num=6, 1 [ 2.298721][ T1] [DISP WRN]: [de_wb_get_reg_blocks:0872]: not support more than 1 wb at present [ 2.325336][ T1] disp 5000000.disp: supply cldo4 not found, using dummy regulator [ 2.346579][ T1] [DISP WRN]: [disp_sys_script_get_item:0202]: of_find_compatible_node allwinner,sunxi-disp1 fail [ 2.360439][ T1] [pq_init]+++ [ 2.375698][ T1] [DISP WRN]: [disp_mgr_protect_reg_for_rcq:1048]: NULL hdl! [ 2.385797][ T1] [DISP WRN]: [disp_mgr_protect_reg_for_rcq:1048]: NULL hdl! [ 2.397176][ T56] [DISP WRN]: [de_top_reset_chn2core_mux:0253]: not expected val=ff00ff0, disp=0 [ 2.410722][ T1] [DISP]disp_module_init finish, ret : 0 [ 2.417069][ T56] [DISP WRN]: [de_top_set_de2tcon_mux:0175]: tcon 0 [ 2.417159][ T1] g2d 5440000.g2d: Adding to iommu group 0 [ 2.426360][ T56] [DISP WRN]: [de_smbl_enable_ahb_read:0552]: de_smbl_enable_ahb_read=1 [ 2.432826][ T1] [G2D] mbus clocK get error! [ 2.443544][ T56] [DISP WRN]: [de_dci_enable_ahb_read:0746]: de_dci_enable_ahb_read=1 [ 2.443596][ T56] [DISP WRN]: [lcd_clk_config:0943]: lcd 0, clk: pll(525000000),clk(525000000),dclk(75000000) dsi_rate(525000000) [ 2.443596][ T56] [ 2.448955][ T1] G2D: Module initialized.major:506 [ 2.459406][ T56] [DISP WRN]: [lcd_clk_config:0945]: clk real:pll(522000000),clk(522000000),dclk(74571428) dsi_rate(0) [ 2.477199][ T1] deinterlace 5400000.deinterlace: Adding to iommu group 0 [ 2.504606][ T1] deinterlace 5400000.deinterlace: version[1.0.0], ip=0x300100 [ 2.513019][ T1] sunxi_sid_init()867 - insmod ok [ 2.518649][ T1] axp2202-usb-power-supply axp2202-usb-power-supply.0: DMA mask not set [ 2.530909][ T1] axp2202_usb_power: axp2202-acin device is not configed, not use vbus-det [ 2.530909][ T1] [ 2.551136][ T1] axp2101-pek axp2101-pek.0: DMA mask not set [ 2.563213][ T1] input: axp2202-pek as /devices/platform/soc@3000000/7081400.s_twi0/i2c-6/6-0035/axp2101-pek.0/input/input0 [ 2.576131][ T1] sunxi-msgbox 3003000.msgbox: sunxi_msgbox_probe(): sunxi msgbox start probe [ 2.585942][ T1] sunxi-msgbox 3003000.msgbox: sunxi_msgbox_probe(): sunxi msgbox probe success [ 2.596271][ T1] sunxi-rproc 7010364.dsp0_rproc: sunxi rproc driver 2.2.6 [ 2.604537][ T1] sunxi-rproc 7010364.dsp0_rproc: memstore num: 0 [ 2.611501][ T1] sunxi-rproc 7010364.dsp0_rproc: hifi4 standby init end [ 2.619477][ T1] remoteproc remoteproc0: dsp0_rproc is available [ 2.626463][ T1] sunxi-rproc 7010364.dsp0_rproc: sunxi rproc driver probe ok [ 2.634587][ T1] sunxi-rproc 7130000.e906_rproc: sunxi rproc driver 2.2.6 [ 2.642365][ T1] sunxi-rproc 7130000.e906_rproc: find rproc priv error [ 2.649825][ T1] sunxi-rproc 7130000.e906_rproc: Failed to get resource [ 2.657378][ T1] remoteproc remoteproc1: releasing e906_rproc [ 2.663980][ T1] sunxi-rproc: probe of 7130000.e906_rproc failed with error -22 [ 2.672971][ T1] sunxi-rpbuf-controller rpbuf_controller@0: assigned reserved memory node dsp0_rpbuf@4ae44000 [ 2.684592][ T1] GACT probability NOT on [ 2.689208][ T1] Mirror/redirect action on [ 2.694015][ T1] netem: version 1.3 [ 2.698244][ T1] u32 classifier [ 2.701985][ T1] input device check on [ 2.706770][ T1] Actions configured [ 2.712664][ T1] xt_time: kernel timezone is -0000 [ 2.718365][ T1] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 2.725586][ T1] gre: GRE over IPv4 demultiplexor driver [ 2.731716][ T1] ip_gre: GRE over IPv4 tunneling driver [ 2.738877][ T1] IPv4 over IPsec tunneling driver [ 2.744857][ T1] Initializing XFRM netlink socket [ 2.750344][ T1] IPsec XFRM device driver [ 2.755687][ T1] NET: Registered PF_INET6 protocol family [ 2.764151][ T1] Segment Routing with IPv6 [ 2.768993][ T1] In-situ OAM (IOAM) with IPv6 [ 2.774234][ T1] mip6: Mobile IPv6 [ 2.778949][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.787219][ T1] ip6_gre: GRE over IPv6 tunneling driver [ 2.793833][ T1] NET: Registered PF_PACKET protocol family [ 2.800198][ T1] NET: Registered PF_KEY protocol family [ 2.806351][ T1] can: controller area network core [ 2.812042][ T1] NET: Registered PF_CAN protocol family [ 2.818075][ T1] can: raw protocol [ 2.822126][ T1] can: broadcast manager protocol [ 2.827501][ T1] can: netlink gateway - max_hops=1 [ 2.833368][ T1] Bluetooth: RFCOMM TTY layer initialized [ 2.839526][ T1] Bluetooth: RFCOMM socket layer initialized [ 2.845965][ T1] Bluetooth: RFCOMM ver 1.11 [ 2.850859][ T1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.858130][ T1] Bluetooth: HIDP socket layer initialized [ 2.864382][ T1] l2tp_core: L2TP core driver, V2.0 [ 2.869941][ T1] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 2.875966][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 2.881343][ T1] tipc: Activated (version 2.0.0) [ 2.886900][ T1] NET: Registered PF_TIPC protocol family [ 2.893163][ T1] tipc: Started in single node mode [ 2.898985][ T1] NET: Registered PF_IEEE802154 protocol family [ 2.905994][ T1] NET: Registered PF_VSOCK protocol family [ 2.913951][ T1] registered taskstats version 1 [ 2.919262][ T1] Loading compiled-in X.509 certificates [ 2.925666][ T99] cryptomgr_probe (99) used greatest stack depth: 15232 bytes left [ 2.928328][ T1] Loaded X.509 cert 'Build time autogenerated kernel key: 6044967aa0897841f2d4a94eeae0e3eb1fd3c229' [ 2.946847][ T1] page_owner is disabled [ 2.951562][ T1] Key type .fscrypt registered [ 2.956644][ T1] Key type fscrypt-provisioning registered [ 2.987384][ T8] sun55iw3-pinctrl 2000000.pinctrl: supply vcc-pb not found, using dummy regulator [ 2.999095][ T8] i2c i2c-0: of_i2c: modalias failure on /soc@3000000/twi0@2502000/ctp@0 [ 3.008195][ T8] i2c i2c-0: Failed to create I2C device for /soc@3000000/twi0@2502000/ctp@0 [ 3.018135][ T8] sunxi-twi 2502000.twi0: sunxi:twi_sunxi:v2.6.2 probe success [ 3.027094][ T8] sunxi-twi 2502800.twi2: sunxi:twi_sunxi:v2.6.2 probe success [ 3.035937][ T8] sunxi-twi 2502c00.twi3: sunxi:twi_sunxi:v2.6.2 probe success [ 3.044703][ T8] sunxi-twi 2503000.twi4: sunxi:twi_sunxi:v2.6.2 probe success [ 3.053933][ T8] sunxi-twi 2503400.twi5: sunxi:twi_sunxi:v2.6.2 probe success [ 3.064159][ T1] hdmi20: [ warn] hdmi_log read sunxi-iova-premap failed! [ 3.071838][ T1] hdmi20: [ info] Get uboot hdmi log failed, malloc a new buffer... [ 3.080484][ T1] hdmi20: [ info] ------- hdmi_log: kernel stage ------ [ 3.087942][ T1] hdmi20: [ info] aw_hdmi_drv_probe: start. [ 3.094306][ T1] hdmi20: [error] _aw_hdmi_dts_parse_pin_config: ddc can not get pinctrl [ 3.103436][ T1] hdmi20: [ info] get hdmi power0: bldo3 is success. [ 3.110859][ T1] hdmi20: [ info] boot hdmi is off [ 3.118506][ T1] hdmi20: [ info] aw_hdmi_drv_probe: finish. [ 3.125274][ T1] hdmi20: [ info] hdmi module init end. [ 3.131294][ T1] hdmi20: [ info] hdmi cec module init end. [ 3.138623][ T1] [DISP WRN]: [disp_sys_pwm_request:0502]: disp_sys_pwm_request pwm 5 fail! -16 [ 3.150529][ T1] [DISP WRN]: [disp_sys_pwm_config:0583]: disp_sys_pwm_Config, handle is NULL! [ 3.162284][ T1] [DISP WRN]: [disp_sys_pwm_set_polarity:0602]: disp_sys_pwm_Set_Polarity, handle is NULL! [ 3.176250][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor0_cameravdd supply, setting it to NULL! [ 3.186970][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor0_iovdd supply, setting it to NULL! [ 3.197303][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor0_avdd supply, setting it to NULL! [ 3.207531][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor0_dvdd supply, setting it to NULL! [ 3.217842][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor1_cameravdd supply, setting it to NULL! [ 3.228553][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor1_iovdd supply, setting it to NULL! [ 3.238880][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor1_avdd supply, setting it to NULL! [ 3.249110][ T1] [VIN_WARN]sensor_helper_probe: cannot get sensor1_dvdd supply, setting it to NULL! [ 3.261421][ T1] vin_isp 5900000.isp: Adding to iommu group 0 [ 3.268636][ T1] vin_isp 5800800.vind:isp@4: Adding to iommu group 0 [ 3.276202][ T1] vin_isp 5800800.vind:isp@5: Adding to iommu group 0 [ 3.283726][ T1] vin_isp 5800800.vind:isp@6: Adding to iommu group 0 [ 3.294458][ T1] vin_scaler 5910000.scaler: Adding to iommu group 0 [ 3.301954][ T1] vin_scaler 5910400.scaler: Adding to iommu group 0 [ 3.309439][ T1] vin_scaler 5910800.scaler: Adding to iommu group 0 [ 3.316881][ T1] vin_scaler 5910c00.scaler: Adding to iommu group 0 [ 3.324320][ T1] vin_scaler 5800800.vind:scaler@16: Adding to iommu group 0 [ 3.332295][ T1] [VIN_ERR]failed to get vipp16 IRQ resource [ 3.338881][ T1] vin_scaler 5800800.vind:scaler@17: Adding to iommu group 0 [ 3.346857][ T1] [VIN_ERR]failed to get vipp17 IRQ resource [ 3.353699][ T1] sunxi-vin-core 5830000.vinc: Adding to iommu group 0 [ 3.361269][ T1] sunxi-vin-core 5831000.vinc: Adding to iommu group 0 [ 3.368831][ T1] sunxi-vin-core 5832000.vinc: Adding to iommu group 0 [ 3.376394][ T1] sunxi-vin-core 5833000.vinc: Adding to iommu group 0 [ 3.383987][ T1] sunxi-vin-core 5834000.vinc: Adding to iommu group 0 [ 3.391532][ T1] sunxi-vin-core 5835000.vinc: Adding to iommu group 0 [ 3.400885][ T1] [VIN_WARN]get csi mipi clk fail [ 3.406272][ T1] [VIN_WARN]get csi mipi src clk fail [ 3.412757][ T1] [VIN]vinc1 is null [ 3.416884][ T1] [VIN]vinc2 is null [ 3.421002][ T1] [VIN]vinc3 is null [ 3.425366][ T1] [VIN]vinc5 is null [ 3.429492][ T1] [VIN]vinc6 is null [ 3.433609][ T1] [VIN]vinc7 is null [ 3.437962][ T1] [VIN]vinc9 is null [ 3.442088][ T1] [VIN]vinc10 is null [ 3.446301][ T1] [VIN]vinc11 is null [ 3.450743][ T1] [VIN]vinc13 is null [ 3.454956][ T1] [VIN]vinc14 is null [ 3.459169][ T1] [VIN]vinc15 is null [ 3.467451][ T1] genirq: irq_chip sunxi_pio_edge did not update eff. affinity mask of irq 442 [ 3.477180][ T1] car-reverse soc@3000000:car-reverse: sunxi:sunxi_car_reverse:[INFO]: [CAR_INFO]: car reverse module probe ok [ 3.490072][ T1] clk: Not disabling unused clocks [ 3.495551][ T1] ALSA device list: [ 3.499572][ T1] No soundcards found. [ 3.504167][ T1] Warning: unable to open an initial console. [ 3.511114][ T1] Freeing unused kernel memory: 1472K [ 3.533019][ T1] Run /init as init process [ 3.537812][ T1] with arguments: [ 3.541834][ T1] /init [ 3.545090][ T1] with environment: [ 3.549301][ T1] HOME=/ [ 3.552646][ T1] TERM=linux [ 3.556379][ T1] snum=0167572d1080c801cd1 [ 3.561447][ T1] mac_addr= [ 3.565086][ T1] wifi_mac= [ 3.568715][ T1] bt_mac= [ 3.572161][ T1] specialstr= [ 3.575990][ T1] boot_type=2 [ 3.579817][ T1] uboot_message=2018.07-g9b0fc4c-dirty(10/12/2023-18:16:20) [ 3.588062][ T1] disp_reserve=4096000,0xb4756000 [ 3.593801][ T1] buildvariant=userdebug [ 3.602145][ T1] init: init first stage started! [ 3.608336][ T1] init: alias lines in modules.alias must have 3 entries, not 4 [ 3.616841][ T1] init: alias lines in modules.alias must have 3 entries, not 5 [ 3.625142][ T1] init: alias lines in modules.alias must have 3 entries, not 4 [ 3.635271][ T106] init: Loading module /lib/modules/zsmalloc.ko with args '' [ 3.635586][ T107] init: Loading module /lib/modules/timer-sun50i.ko with args '' [ 3.635686][ T108] init: Loading module /lib/modules/tee.ko with args '' [ 3.635952][ T109] init: Loading module /lib/modules/sunxi-vendor-hooks.ko with args '' [ 3.636076][ T110] init: Loading module /lib/modules/sunxi-uart.ko with args '' [ 3.636075][ T109] sunxi_vendor_hooks: module verification failed: signature and/or required key missing - tainting kernel [ 3.636357][ T111] init: Loading module /lib/modules/sunxi_mm.ko with args '' [ 3.699751][ T111] sunxi_mm: Register sunxi direct_swappiness passed. [ 3.700419][ T110] sun55iw3-pinctrl 2000000.pinctrl: unknown pin [ 3.700455][ T113] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11 [ 3.700513][ T113] [ADDR_MGT] addr_mgt_probe: success. [ 3.700580][ T107] sun55iw3-timer 3008000.timer: sun50i timer init:0xffffff00000007 [ 3.700590][ T107] clocksource: timer: mask: 0xffffffffffffff max_cycles: 0x1623fa770, max_idle_ns: 440795202238 ns [ 3.706985][ T111] sunxi_mm: Register sunxi swappiness passed. [ 3.708482][ T106] sun50i_cpufreq_nvmem: dvfs: 0x29, vf2 [ 3.708593][ T108] Saving SoC boot-reason: COLD-BOOT [ 3.708613][ T108] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1 [ 3.708645][ T108] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 3.708929][ T108] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 3.708996][ T108] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 3.709439][ T108] sunxi-rtc 7090000.rtc: registered as rtc0 [ 3.709455][ T108] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate! [ 3.709497][ T108] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:06 UTC (6) [ 3.709527][ T108] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 3.710478][ T108] init (108) used greatest stack depth: 11632 bytes left [ 3.713687][ T110] sun55iw3-pinctrl 2000000.pinctrl: unknown pin [ 3.714995][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.715004][ T107] cpu cpu0: _opp_add: OPP not supported by regulators (408000000) [ 3.715348][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.715355][ T107] cpu cpu0: _opp_add: OPP not supported by regulators (720000000) [ 3.715925][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.715932][ T107] cpu cpu0: _opp_add: OPP not supported by regulators (1128000000) [ 3.716173][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.716180][ T107] cpu cpu0: _opp_add: OPP not supported by regulators (1296000000) [ 3.716753][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.716760][ T107] cpu cpu4: _opp_add: OPP not supported by regulators (408000000) [ 3.717146][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.717153][ T107] cpu cpu4: _opp_add: OPP not supported by regulators (720000000) [ 3.717615][ T107] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 3.717622][ T107] cpu cpu4: _opp_add: OPP not supported by regulators (1248000000) [ 3.720359][ T107] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1296000 KHz, changing to: 1320000 KHz [ 3.720750][ T107] cpu cpu0: EM: created perf domain [ 3.721353][ T106] BOOTEVENT: 3721.351860: ON [ 3.723337][ T107] cpu cpu4: EM: created perf domain [ 3.725692][ T107] init (107) used greatest stack depth: 10256 bytes left [ 3.726503][ T110] uart 2500000.uart: there is not valid maps for state default [ 3.745635][ T109] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.746231][ T110] sun55iw3-pinctrl 2000000.pinctrl: unknown pin [ 3.753284][ T109] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.758270][ T110] sun55iw3-pinctrl 2000000.pinctrl: unknown pin [ 3.763856][ T104] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.776692][ T110] uart 2500000.uart: there is not valid maps for state sleep [ 3.785840][ T104] cfg80211: failed to load regulatory.db [ 4.081382][ T110] uart uart0: uart0 error to get fifo size property [ 4.088333][ T110] uart0: ttyAS0 at MMIO 0x2500000 (irq = 106, base_baud = 1500000) is a SUNXI [ 4.097676][ T110] sw_console_setup()1863 - console setup baud 115200 parity n bits 8, flow n [ 4.106971][ T110] printk: console [ttyAS0] enabled [ 4.106971][ T110] printk: console [ttyAS0] enabled [ 4.117836][ T110] printk: bootconsole [uart8250] disabled [ 4.117836][ T110] printk: bootconsole [uart8250] disabled [ 4.130738][ T110] uart uart1: supply uart not found, using dummy regulator [ 4.138777][ T110] uart1: ttyAS1 at MMIO 0x2500400 (irq = 107, base_baud = 1500000) is a SUNXI [ 4.149048][ T110] uart uart6: supply uart not found, using dummy regulator [ 4.157083][ T110] uart6: ttyAS6 at MMIO 0x2501800 (irq = 108, base_baud = 1500000) is a SUNXI [ 4.170193][ T120] dsu dvfs: vf2 [ 4.174271][ T120] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 4.174828][ T121] optee: probing for conduit method. [ 4.175272][ T118] zram: Added device: zram0 [ 4.175585][ T119] sunxi-mmc 4022000.sdmmc: SD/MMC/SDIO Host Controller Driver(v5.36 2023-8-2 14:31) [ 4.175907][ T119] sunxi-mmc 4022000.sdmmc: ctl-spec-caps 308 [ 4.176183][ T119] sunxi-mmc 4022000.sdmmc: No vdmmc regulator found [ 4.176189][ T119] sunxi-mmc 4022000.sdmmc: No vd33sw regulator found [ 4.176192][ T119] sunxi-mmc 4022000.sdmmc: No vd18sw regulator found [ 4.176195][ T119] sunxi-mmc 4022000.sdmmc: No vq33sw regulator found [ 4.176198][ T119] sunxi-mmc 4022000.sdmmc: No vq18sw regulator found [ 4.176211][ T119] sunxi-mmc 4022000.sdmmc: Cann't get uart0 pinstate,check if needed [ 4.176214][ T119] sunxi-mmc 4022000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 4.176708][ T119] sunxi-mmc 4022000.sdmmc: ***ctl-cmdq-md*** 20 [ 4.185232][ T120] sunxi-dsufreq 8815000.dsufreq: _opp_add: OPP not supported by regulators (288000000) [ 4.190823][ T121] optee: revision 3.7 (3d360a47) [ 4.191169][ T119] sunxi-mmc 4022000.sdmmc: cq_host:ffffff80c7809080, mmc:ffffff80c7658000, host:ffffff80c76587c0 [ 4.191182][ T119] mmc0: CQHCI version 0.00 [ 4.191311][ T119] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.195880][ T120] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 4.203890][ T119] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.206198][ T121] optee: initialized driver [ 4.212575][ T120] sunxi-dsufreq 8815000.dsufreq: _opp_add: OPP not supported by regulators (528000000) [ 4.216507][ T119] sunxi-mmc 4022000.sdmmc: detmode:alway in(non removable) [ 4.216522][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.217500][ T119] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v5.36 2023-8-2 14:31) [ 4.217729][ T119] sunxi-mmc 4020000.sdmmc: ctl-spec-caps 408 [ 4.218078][ T119] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 4.218082][ T119] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 4.218519][ T119] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 4.218559][ T119] sunxi-mmc 4020000.sdmmc: cd-set-debounce is 0x1 [ 4.219504][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.220837][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.227295][ T119] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.227678][ T120] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 4.227684][ T120] sunxi-dsufreq 8815000.dsufreq: _opp_add: OPP not supported by regulators (1008000000) [ 4.227854][ T120] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 4.227859][ T120] sunxi-dsufreq 8815000.dsufreq: _opp_add: OPP not supported by regulators (1104000000) [ 4.227963][ T120] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator [ 4.227968][ T120] sunxi-dsufreq 8815000.dsufreq: _opp_add: OPP not supported by regulators (1128000000) [ 4.273903][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.274103][ T119] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 4.284750][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.300956][ T119] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.304651][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm OD pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.317352][ T119] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 4.347017][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 1 timing LEGACY(SDR12) dt B [ 4.357320][ T119] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v5.36 2023-8-2 14:31) [ 4.377373][ T71] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01) [ 4.387511][ T119] sunxi-mmc 4021000.sdmmc: ctl-spec-caps 408 [ 4.393796][ T71] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01) [ 4.401038][ T119] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 4.408186][ T71] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01) [ 4.414103][ T119] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 4.421116][ T71] sunxi-mmc 4022000.sdmmc: avoid to switch power_off_notification to POWERED_ON(0x01) [ 4.426257][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 8 timing LEGACY(SDR12) dt B [ 4.433446][ T119] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 4.433450][ T119] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 4.433453][ T119] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 4.448057][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS200 dt B [ 4.457641][ T119] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 4.457644][ T119] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 4.457647][ T119] sunxi-mmc 4021000.sdmmc: manual set ocr [ 4.468415][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 52000000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS200 dt B [ 4.479017][ T119] sunxi-mmc 4021000.sdmmc: Cann't get uart0 pinstate,check if needed [ 4.489903][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 150000000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS200 dt B [ 4.500378][ T119] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 4.521037][ T117] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 4.522078][ T119] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 4.526422][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 150000000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS(SDR20) dt B [ 4.526491][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 52000000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS(SDR20) dt B [ 4.526945][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS400 dt B [ 4.527018][ T71] sunxi-mmc 4022000.sdmmc: sdc set ios:clk 150000000Hz bm PP pm ON vdd 23 width 8 timing MMC-HS400 dt B [ 4.854883][ T71] mmc0: Command Queue Engine enabled [ 4.860653][ T71] mmc0: new HS400 MMC card at address 0001 [ 4.867257][ T119] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 4.867692][ T71] mmcblk0: mmc0:0001 A3A561 57.6 GiB [ 4.892204][ T71] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 [ 4.892318][ T119] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 4.907123][ T71] mmcblk0rpmb: mmc0:0001 A3A561 16.0 MiB, chardev (234:0) [ 4.913997][ C0] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !! [ 4.929433][ C0] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !! [ 4.937039][ T56] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 4.952377][ T56] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 4.966904][ C0] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 4.975218][ C0] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 4.983570][ C0] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 4.991932][ C0] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 4.999478][ T56] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 5.000482][ T1] EXT4-fs (mmcblk0p21): Ignoring removed nomblk_io_submit option [ 5.024593][ T1] EXT4-fs (mmcblk0p21): recovery complete [ 5.030955][ T1] EXT4-fs (mmcblk0p21): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit. Quota mode: none. [ 5.048699][ T138] random: e2fsck: uninitialized urandom read (40 bytes read) [ 5.057987][ T1] e2fsck: linker: Warning: failed to find generated linker configuration from "/linkerconfig/ld.config.txt" [ 5.063375][ T138] random: e2fsck: uninitialized urandom read (40 bytes read) [ 5.070685][ T1] e2fsck: WARNING: linker: Warning: failed to find generated linker configuration from "/linkerconfig/ld.config.txt" [ 5.092287][ T1] e2fsck: e2fsck 1.46.2 (28-Feb-2021) [ 5.098128][ T1] e2fsck: Pass 1: Checking inodes, blocks, and sizes [ 5.105416][ T1] e2fsck: Pass 2: Checking directory structure [ 5.112140][ T1] e2fsck: Pass 3: Checking directory connectivity [ 5.119151][ T1] e2fsck: Pass 4: Checking reference counts [ 5.125573][ T1] e2fsck: Pass 5: Checking group summary information [ 5.132871][ T1] e2fsck: /dev/block/by-name/metadata: 31/4096 files (0.0% non-contiguous), 1568/4096 blocks [ 5.151014][ T1] EXT4-fs (mmcblk0p21): mounted filesystem with ordered data mode. Opts: errors=panic. Quota mode: none. [ 5.166026][ T1] random: init: uninitialized urandom read (16 bytes read) [ 5.179953][ T1] erofs: (device dm-0): mounted with root inode @ nid 65. [ 5.191876][ T1] EXT4-fs (dm-4): mounted filesystem without journal. Opts: . Quota mode: none. [ 5.202969][ T1] erofs: (device dm-1): mounted with root inode @ nid 42. [ 5.211993][ T1] erofs: (device dm-3): mounted with root inode @ nid 39. [ 5.220680][ T1] erofs: (device dm-2): mounted with root inode @ nid 39. [ 5.229722][ T1] EXT4-fs (mmcblk0p22): Ignoring removed nomblk_io_submit option [ 5.241594][ T1] EXT4-fs (mmcblk0p22): recovery complete [ 5.247958][ T1] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit. Quota mode: none. [ 5.266927][ T1] e2fsck: executing /system/bin/e2fsck failed: No such file or directory [ 5.278195][ T1] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: errors=panic. Quota mode: none. [ 5.297800][ T1] SELinux: Unable to set superblock options before the security server is initialized [ 5.314616][ T1] FAT-fs (mmcblk0p27): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 5.368257][ T1] printk: init: 5 output lines suppressed due to ratelimiting [ 5.376546][ T1] printk: init: 90 output lines suppressed due to ratelimiting [ 5.500663][ T1] init: DM_DEV_STATUS failed for system_ext_a: No such device or address [ 5.509983][ T1] init: Could not update logical partition [ 5.516411][ T1] init: Opening SELinux policy [ 5.522999][ T1] init: Falling back to standard signature check. TODO implementent support for fsverity SEPolicy. [ 5.534886][ T1] init: Error: Apex SEPolicy failed signature check [ 5.542182][ T1] init: Loading APEX Sepolicy from /system/etc/selinux/apex/SEPolicy.zip [ 5.551530][ T1] init: Failed to open package /system/etc/selinux/apex/SEPolicy.zip: No such file or directory [ 5.569149][ T1] init: Loading SELinux policy [ 5.595554][ T1] SELinux: Permission bpf in class capability2 not defined in policy. [ 5.604632][ T1] SELinux: Permission checkpoint_restore in class capability2 not defined in policy. [ 5.615124][ T1] SELinux: Permission bpf in class cap2_userns not defined in policy. [ 5.624161][ T1] SELinux: Permission checkpoint_restore in class cap2_userns not defined in policy. [ 5.634768][ T1] SELinux: Class mctp_socket not defined in policy. [ 5.642076][ T1] SELinux: the above unknown classes and permissions will be denied [ 5.656372][ T1] SELinux: policy capability network_peer_controls=1 [ 5.663805][ T1] SELinux: policy capability open_perms=1 [ 5.670131][ T1] SELinux: policy capability extended_socket_class=1 [ 5.677523][ T1] SELinux: policy capability always_check_network=0 [ 5.684809][ T1] SELinux: policy capability cgroup_seclabel=0 [ 5.691622][ T1] SELinux: policy capability nnp_nosuid_transition=1 [ 5.699010][ T1] SELinux: policy capability genfs_seclabel_symlinks=0 [ 5.706589][ T1] SELinux: policy capability ioctl_skip_cloexec=0 [ 5.897196][ T72] audit: type=1403 audit(8.684:2): auid=4294967295 ses=4294967295 lsm=selinux res=1 [ 5.907219][ T1] selinux: SELinux: Loaded file_contexts [ 5.913685][ T1] selinux: [ 5.946950][ T1] init: init second stage started! [ 6.011423][ T1] init: Using Android DT directory /proc/device-tree/firmware/android/ [ 6.027008][ T1] init: Couldn't load property file '/vendor/default.prop': open() failed: No such file or directory: No such file or directory [ 6.047074][ T1] init: Couldn't load property file '/odm_dlkm/etc/build.prop': open() failed: No such file or directory: No such file or directory [ 6.063744][ T1] init: Couldn't load property file '/oem/build.prop': open() failed: No such file or directory: No such file or directory [ 6.078517][ T1] init: Could not set 'ro.boot.dynamic_partitions' to 'true' while loading .prop filesRead-only property was already set [ 6.092479][ T1] init: Could not set 'ro.boot.dynamic_partitions_retrofit' to 'true' while loading .prop filesRead-only property was already set [ 6.108761][ T1] init: Setting product property ro.product.brand to 'Allwinner' (from ro.product.product.brand) [ 6.120397][ T1] init: Setting product property ro.product.device to 't527-demo-car' (from ro.product.product.device) [ 6.132605][ T1] init: Setting product property ro.product.manufacturer to 'Allwinner' (from ro.product.product.manufacturer) [ 6.186215][ T158] random: init: uninitialized urandom read (40 bytes read) [ 6.215237][ T158] random: init: uninitialized urandom read (40 bytes read) [ 6.328774][ T159] random: linkerconfig: uninitialized urandom read (40 bytes read) [ 6.343504][ T159] linkerconfig: Unable to access VNDK APEX at path: /apex/com.android.vndk.v33: No such file or directory [ 6.356236][ T159] linkerconfig: Unable to access VNDK APEX at path: /apex/com.android.vndk.v33: No such file or directory [ 6.403071][ T160] ueventd: ueventd started! [ 6.411749][ T160] selinux: SELinux: Loaded file_contexts [ 6.418660][ T160] selinux: [ 6.422840][ T160] ueventd: Parsing file /system/etc/ueventd.rc... [ 6.430082][ T160] ueventd: Added '/vendor/etc/ueventd.rc' to import list [ 6.437856][ T160] ueventd: Added '/odm/etc/ueventd.rc' to import list [ 6.445322][ T161] apexd: Bootstrap subcommand detected [ 6.446134][ T160] ueventd: Parsing file /vendor/etc/ueventd.rc... [ 6.451371][ T161] apexd: ActivateFlattenedApex [ 6.458760][ T160] ueventd: Parsing file /odm/etc/ueventd.rc... [ 6.463519][ T161] apexd: Scanning /system/apex [ 6.470253][ T160] ueventd: Unable to read config file '/odm/etc/ueventd.rc': open() failed: No such file or directory [ 6.475949][ T161] apexd: Bind mounting /system/apex/com.android.adbd onto /apex/com.android.adbd [ 6.498261][ T161] apexd: Bind mounting /system/apex/com.android.adservices onto /apex/com.android.adservices [ 6.510146][ T161] apexd: Bind mounting /system/apex/com.android.appsearch onto /apex/com.android.appsearch [ 6.521923][ T161] apexd: Bind mounting /system/apex/com.android.art onto /apex/com.android.art [ 6.532480][ T161] apexd: Bind mounting /system/apex/com.android.btservices onto /apex/com.android.btservices [ 6.544387][ T161] apexd: Bind mounting /system/apex/com.android.conscrypt onto /apex/com.android.conscrypt [ 6.555990][ T161] apexd: Bind mounting /system/apex/com.android.extservices onto /apex/com.android.extservices [ 6.588101][ T161] printk: apexd: 24 output lines suppressed due to ratelimiting [ 6.925992][ T175] prng_seeder: Hanging forever because setup failed: hwrng.read_exact in new [ 6.925992][ T175] [ 6.938205][ T175] Caused by: [ 6.941676][ T175] No such device (os error 19) [ 6.957766][ T158] sunxi-rfkill soc@3000000:rfkill: module version: v1.1.4 [ 6.965632][ T158] sunxi-rfkill soc@3000000:rfkill: pinctrl_lookup_state(default) failed! return ffffffffffffffed [ 6.977360][ T158] sunxi-rfkill soc@3000000:rfkill: get gpio chip_en failed [ 6.985280][ T158] sunxi-rfkill soc@3000000:rfkill: get gpio power_en failed [ 6.993431][ T158] sunxi-rfkill soc@3000000:rfkill: wlan_busnum (1) [ 7.000808][ T158] sunxi-rfkill soc@3000000:rfkill: wlan power[0] (axp2202-dcdc4) voltage: 3300mV [ 7.011024][ T158] sunxi-rfkill soc@3000000:rfkill: wlan power[1] (axp2202-bldo1) voltage: 1800mV [ 7.021134][ T158] sunxi-rfkill soc@3000000:rfkill: wlan_regon gpio=385 assert=1 [ 7.027869][ T160] ueventd: Coldboot took 0.539 seconds [ 7.029588][ T158] sun55iw3-r-pinctrl 7022000.pinctrl: supply vcc-pm not found, using dummy regulator [ 7.046408][ T158] sunxi-rfkill soc@3000000:rfkill: wlan_hostwake gpio=384 assert=1 [ 7.055131][ T158] sunxi-rfkill soc@3000000:rfkill: wakeup source is enabled [ 7.063127][ T158] sunxi-rfkill soc@3000000:rfkill: wlan power boot-on: 0, always-on: 0 [ 7.072357][ T158] sunxi-rfkill soc@3000000:rfkill: bt power[0] (axp2202-dcdc4) voltage: 3300mV [ 7.082262][ T158] sunxi-rfkill soc@3000000:rfkill: bt power[1] (axp2202-bldo1) voltage: 1800mV [ 7.092151][ T158] sunxi-rfkill soc@3000000:rfkill: bt_rst gpio=386 assert=0 [ 7.100181][ T158] sunxi-rfkill soc@3000000:rfkill: bluetooth power boot-on: 0, always-on: 0 [ 7.198269][ T1] Registered swp emulation handler [ 7.226519][ T179] random: logd: uninitialized urandom read (40 bytes read) [ 7.233635][ T180] random: lmkd: uninitialized urandom read (40 bytes read) [ 7.238556][ T181] random: servicemanager: uninitialized urandom read (40 bytes read) [ 7.283445][ T179] logd.auditd: start console:/ $ [ 7.287867][ T179] logd.klogd: 7122888961 [ 7.294755][ T158] inno-combphy 4f00000.phy: Sub System Version: 0x10000 [ 7.308597][ T179] logd: Loaded bug_map file: /system_ext/etc/selinux/bug_map [ 7.317016][ T179] logd: Loaded bug_map file: /vendor/etc/selinux/selinux_denial_metadata [ 7.327023][ T179] logd: Loaded bug_map file: /system/etc/selinux/bug_map [ 7.333333][ T189] treadahead: /treadahead/readahead_file_offset not exist; [ 7.342844][ T189] treadahead: go to open trace [ 7.470130][ T197] type=1400 audit(10.256:3): avc: denied { getattr } for comm="init" path="/sys/kernel/debug/devices_deferred" dev="debugfs" ino=17452 scontext=u:r:init:s0 tcontext=u:object_r:debugfs:s0 tclass=file permissive=1 [ 7.493407][ T197] type=1400 audit(10.256:4): avc: denied { getattr } for comm="init" path="/sys/kernel/debug/wakeup_sources" dev="debugfs" ino=2051 scontext=u:r:init:s0 tcontext=u:object_r:debugfs_wakeup_sources:s0 tclass=file permissive=1 [ 7.627159][ T211] vdc: Waited 0ms for vold [ 7.633643][ T207] AW_keymint_2 : starting aw keymint service [ 7.634293][ T207] AW_keymint_2 : message_version:4 [ 7.646608][ T207] AW_keymint_2 : load ta: [ 7.646648][ T207] AW_keymint_2 : 0a 82 10 d5 27 9c 83 49 ad 73 f8 b3 01 0a cd 04 [ 7.666248][ T212] vdc: Waited 0ms for vold [ 8.737450][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 9.755559][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 10.773566][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 11.791566][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 12.713261][ T225] random: crash_dump64: uninitialized urandom read (40 bytes read) [ 12.809475][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 12.813176][ T190] logd: logdr: UID=1017 GID=1017 PID=226 n tail=0 logMask=8 pid=205 start=0ns deadline=0ns [ 12.838644][ T190] logd: logdr: UID=1017 GID=1017 PID=226 n tail=0 logMask=1 pid=205 start=0ns deadline=0ns [ 12.850432][ T226] DEBUG: *** *** *** *** *** *** *** *** *** *** *** *** *** *** *** *** [ 12.850534][ T226] DEBUG: Build fingerprint: 'Allwinner/t527_demo_car_arm64/t527-demo-car:13/TQ2A.230405.003.B2/eng.lizhi.20230927.185912:userdebug/test-keys' [ 12.859931][ T226] DEBUG: Revision: '0' [ 12.876032][ T226] DEBUG: ABI: 'arm64' [ 12.880533][ T226] DEBUG: Timestamp: 1970-01-01 08:00:15.539019545+0800 [ 12.884957][ T226] DEBUG: Process uptime: 6s [ 12.892584][ T226] DEBUG: Cmdline: /system/bin/keystore2 /data/misc/keystore [ 12.897585][ T226] DEBUG: pid: 205, tid: 205, name: binder:205_2 >>> /system/bin/keystore2 <<< [ 12.905699][ T226] DEBUG: uid: 1017 [ 12.915641][ T226] DEBUG: tagged_addr_ctrl: 0000000000000001 (PR_TAGGED_ADDR_ENABLE) [ 12.919712][ T226] DEBUG: signal 6 (SIGABRT), code -1 (SI_QUEUE), fault addr -------- [ 12.928598][ T226] DEBUG: Abort message: 'Failed to create service android.system.keystore2.IKeystoreService/default because of In KeystoreService::new_native_binder: Trying to construct mandatory security level TEE. [ 12.959109][ T226] DEBUG: [ 12.962248][ T226] DEBUG: Caused by: [ 12.966371][ T226] DEBUG: 0: In KeystoreSecurityLevel::new_native_binder. [ 12.974471][ T226] DEBUG: 1: In get_keymint_device. [ 12.980423][ T226] DEBUG: 2: In connect_keymint: Trying to connect to genuine KeyMint service. [ 12.990575][ T226] DEBUG: 3: Binder transaction error NAME_NOT_FOUND.' [ 12.990661][ T226] DEBUG: x0 0000000000000000 x1 00000000000000cd x2 0000000000000006 x3 0000007fd40a9380 [ 12.998544][ T226] DEBUG: x4 0000000000808080 x5 0000000000808080 x6 0000000000808080 x7 8080808080808080 [ 13.010527][ T226] DEBUG: x8 00000000000000f0 x9 000000797f109a70 x10 0000000000000001 x11 000000797f17ae2c [ 13.022508][ T226] DEBUG: x12 0101010101010101 x13 72657320746e694d x14 0000000000000001 x15 0000000000000030 [ 13.034475][ T226] DEBUG: x16 000000797f1e2a40 x17 000000797f1bccb0 x18 0000007987166000 x19 00000000000000cd [ 13.046462][ T226] DEBUG: x20 00000000000000cd x21 00000000ffffffff x22 00000057957c6080 x23 0000000000000000 [ 13.058439][ T226] DEBUG: x24 0000000000000001 x25 00000057957da750 x26 00000057957da7a8 x27 0000007fd40a9690 [ 13.070413][ T226] DEBUG: x28 00000057957d5c10 x29 0000007fd40a9400 [ 13.082448][ T226] DEBUG: lr 000000797f16c9e8 sp 0000007fd40a9360 pc 000000797f16ca14 pst 0000000000001000 [ 13.090146][ T226] DEBUG: backtrace: [ 13.102129][ T226] DEBUG: #00 pc 000000000008aa14 /apex/com.android.runtime/lib64/bionic/libc.so (abort+164) (BuildId: 86827b27b123a9879220ea6b489eecf5) [ 13.106294][ T226] DEBUG: #01 pc 00000000001576ac /system/bin/keystore2 (_RNvNvCs2yrrfPAoZZX_11panic_abort18___rust_start_panic5abort.llvm.16868985108068327187+4) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.122458][ T226] DEBUG: #02 pc 00000000001576a0 /system/bin/keystore2 (__rust_start_panic+8) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.143874][ T226] DEBUG: #03 pc 0000000000165c5c /system/bin/keystore2 (rust_panic+16) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.158680][ T226] DEBUG: #04 pc 000000000016592c /system/bin/keystore2 (_RNvNtCs4p8YLn7dL5m_3std9panicking20rust_panic_with_hook+996) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.172797][ T226] DEBUG: #05 pc 0000000000165498 /system/bin/keystore2 (_RNCNvNtCs4p8YLn7dL5m_3std9panicking19begin_panic_handler0B5_.llvm.8848384190362852836+112) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.191519][ T226] DEBUG: #06 pc 0000000000163d90 /system/bin/keystore2 (_RINvNtNtCs4p8YLn7dL5m_3std10sys_common9backtrace26___rust_end_short_backtraceNCNvNtB6_9panicking19begin_panic_handler0zEB6_.llvm.8848384190362852836+16) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.213116][ T226] DEBUG: #07 pc 000000000016526c /system/bin/keystore2 (rust_begin_unwind+36) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.240796][ T226] DEBUG: #08 pc 0000000000077388 /system/bin/keystore2 (_RNvNtCsl9ljXaK2GKD_4core9panicking9panic_fmt+36) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.255591][ T226] DEBUG: #09 pc 00000000000465dc /system/bin/keystore2 (_RNvCsdV139EorvfX_14keystore2_main4main+4872) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.273147][ T226] DEBUG: #10 pc 00000000000469bc /system/bin/keystore2 (_RNCINvNtCs4p8YLn7dL5m_3std2rt10lang_startuE0CsdV139EorvfX_14keystore2_main+8) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.290281][ T226] DEBUG: #11 pc 0000000000163788 /system/bin/keystore2 (_RNvNtCs4p8YLn7dL5m_3std2rt19lang_start_internal+344) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.310620][ T226] DEBUG: #12 pc 0000000000046ac0 /system/bin/keystore2 (main+40) (BuildId: fb0dc1a83c1d0a0dcc1bc19bb94ad839) [ 13.328526][ T226] DEBUG: #13 pc 0000000000083290 /apex/com.android.runtime/lib64/bionic/libc.so (__libc_init+96) (BuildId: 86827b27b123a9879220ea6b489eecf5) [ 13.827612][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 14.862341][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 15.880254][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 16.898159][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 17.916119][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 18.934170][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 19.952109][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 20.970094][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 21.988158][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 23.006073][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 23.682814][ T117] axp2202_usb_power: current limit not set: usb adapter type [ 23.682814][ T117] [ 24.023980][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 24.209086][ T71] pdtest 0.pd-ve-test: runtime_suspend disable clock [ 24.216440][ T71] pdtest 0.pd-vi-test: runtime_suspend disable clock [ 24.223776][ T71] pdtest 0.pd-vo0-test: runtime_suspend disable clock [ 24.231193][ T71] pdtest 0.pd-vo1-test: runtime_suspend disable clock [ 24.238609][ T71] pdtest 0.pd-de-test: runtime_suspend disable clock [ 24.245924][ T71] pdtest 0.pd-nand-test: runtime_suspend disable clock [ 24.253449][ T71] pdtest 0.pd-pcie-test: runtime_suspend disable clock [ 24.260961][ T71] pdtest 0.pd-dsp-test: runtime_suspend disable clock [ 24.268380][ T71] pdtest 0.pd-npu-test: runtime_suspend disable clock [ 24.275803][ T71] pdtest 0.pd-sram-test: runtime_suspend disable clock [ 24.283320][ T71] pdtest 0.pd-riscv-test: runtime_suspend disable clock [ 25.042027][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 26.060084][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 27.078015][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 28.096119][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 29.114068][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 30.131985][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?) [ 31.149934][ T195] ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?)后面的log基本都是
ServiceManager: Waited one second for android.system.keystore2.IKeystoreService/default (is service started? are binder threads started and available?)这个服务报错的错误log为
[ 12.928598][ T226] DEBUG: Abort message: 'Failed to create service android.system.keystore2.IKeystoreService/default because of In KeystoreService::new_native_binder: Trying to construct mandatory security level TEE. [ 12.959109][ T226] DEBUG: [ 12.962248][ T226] DEBUG: Caused by: [ 12.966371][ T226] DEBUG: 0: In KeystoreSecurityLevel::new_native_binder. [ 12.974471][ T226] DEBUG: 1: In get_keymint_device. [ 12.980423][ T226] DEBUG: 2: In connect_keymint: Trying to connect to genuine KeyMint service. [ 12.990575][ T226] DEBUG: 3: Binder transaction error NAME_NOT_FOUND.'但是keymint服务似乎已经启动?
[ 7.633643][ T207] AW_keymint_2 : starting aw keymint service [ 7.634293][ T207] AW_keymint_2 : message_version:4 [ 7.646608][ T207] AW_keymint_2 : load ta: [ 7.646648][ T207] AW_keymint_2 : 0a 82 10 d5 27 9c 83 49 ad 73 f8 b3 01 0a cd 04辛苦大家帮我看看
-
Android13编译不过发布在 编译和烧写问题专区
编译安卓13编译报错，我没什么头绪，麻烦大家帮忙看看怎么想办法解决
registry_table has NOT been set. Please check it.
-
回复: A133 android10.0 lvds显示异常发布在 其它全志芯片讨论区
@whycanservice2 谢谢，已经把问题解决了，是电压异常的两个引脚被串口复用了，之前检查引脚的时候看漏了，现在已经正常显示，谢谢
-
回复: A133 android10.0 lvds显示异常发布在 其它全志芯片讨论区
@whycanservice2 在 A133 android10.0 lvds显示异常 中说：
vcom
谢谢，我对照着A40i测了接口的电压，
A40i: RXE3- 1.2v RXE3+ 1.3 v RXE1- 0.8 v RXE1+ 1.4v
A133:RXE3- 1.3v RXE3+ 2.6v RXE1- 1.0v RXE1+ 2.9v
其他引脚都差不多，这样算是正常吗，我应该怎么测量呢？ -
回复: A133 android10.0 lvds显示异常发布在 其它全志芯片讨论区
@whycanservice2 谢谢，我试过了，但是没效果，目前开机和进后系统后的情况是下面这样的
麻烦再帮我看看可能是什么问题，dts使用的配置完全与A40i（android 7）是一样的，A40i 显示正常 -
A40i修改uart_debug_port之后烧录不了发布在 飞凌嵌入式专区
原本使用的是uart0
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PB22<2><1><default><default>
uart_debug_rx = port:PB23<2><1><default><default>
想要改为别的串口，比如uart2，但是改了之后烧录不了
[uart_para]
uart_debug_port = 2
uart_debug_tx = port:PI18<3><1><default><default>
uart_debug_rx = port:PI19<3><1><default><default>
试过改成其他的也不行，只有将下面的内容注释是可以烧录的，烧录后进文件系统后会在uart0输出日志信息
[uart_para]
;uart_debug_port = 0
;uart_debug_tx = port:PB22<2><1><default><default>
;uart_debug_rx = port:PB23<2><1><default><default>
请问有没有什么办法解决？ -
回复: 请问不同驱动中的probe函数执行顺序是怎么样的？发布在 Linux
@whycanservice 谢谢回复。
我已经在clk驱动中将module_platform_driver(clk_driver);
改成了
static int __init clk_init(void)
{
return platform_driver_register(&clk_driver);
}
arch_initcall(clk_init);//arch_initcall 等级为3
我通过kernel log 看，clk_driver 执行probe的时间确实有提前，但是有的使用module_init的驱动还是会在clk_driver之前执行probe。这让我感觉很疑惑。
我想过将驱动编译为module,但是clk涉及到很多功能，像是gpio，lcd，audio等，如果将上述的驱动都使用module，那就涉及到这些部分的驱动可能都需要编译成module，这样做是否会很奇怪。 -
请问不同驱动中的probe函数执行顺序是怎么样的？发布在 Linux
最近遇到一个问题，内核启动的时候clk probe函数没有执行，导致很多功能在获取clk的时候报错，我尝试过修改驱动init的等级比如将module_init改为arch_initcall,这样操作，有时候确实有效，但是并不是都有效。
所以我想请问一下大佬，probe的顺序是否能够修改？谢谢 -
回复: RTL8723bu模块AP模式的问题发布在 Linux
@masterlu 目前发现单独编译出来的8723bu.ko文件安装上去能够正常使用ap，整体编译内核输出在output/lib/modules/3.10.65下的8723bu.ko文件无法使用ap，会报No WPA/RSN IE from STA的错误。
-
RTL8723bu模块AP模式的问题发布在 Linux
RTL8723bu模块STA模式功能正常，AP模式不设置密码可以连接，设置密码后无法连接，报错信息为No WPA/RSN IE from STA。内核版本为3.10.65
在客户平台有有一条类似的问题《Tina-xr829无法连接加密ap》https://open.allwinnertech.com/#/faq/0/show，仿照这条问题进行修改，依然没有效果。
希望有大佬能给一下解决思路。 -
回复: A40I AP问题发布在 飞凌嵌入式专区
@masterlu
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd.conf
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Using driver-based off-channel TX
nl80211: key_mgmt=0xd0f enc=0xf auth=0x7 flags=0x800d8c0 rrm_flags=0x0 probe_resp_offloads=0x0 max_stations=0 max_remain_on_chan=5000 max_scan_ssids=9
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 7 iftype 3 (AP)
nl80211: Setup AP(wlan0) - device_ap_sme=1 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x1dfbdd0 (device SME)
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=04 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=0501 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=0503 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=0504 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=06 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=08 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=09 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=0a multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=11 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x1dfbdd0 match=7f multicast=0
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x1dfbdd0 match= multicast=0
nl80211: Enable Probe Request reporting nl_preq=0x1e00ea0
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x1e00ea0 match= multicast=0
rfkill: Cannot open RFKILL control device
nl80211: RFKILL status not available
nl80211: Add own interface ifindex 7 (ifidx_reason -1)
nl80211: if_indices[16]: 7(-1)
phy: phy0
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: No channel number found for frequency 5920 MHz
nl80211: No channel number found for frequency 5940 MHz
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
nl80211: Mode IEEE 802.11g: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467[NO_IR] 2472[NO_IR] 2484[DISABLED]
nl80211: Mode IEEE 802.11a: 5170[DISABLED] 5180[DISABLED] 5190[DISABLED] 5200[DISABLED] 5210[DISABLED] 5220[DISABLED] 5230[DISABLED] 5240[DISABLED] 5260[DISABLED] 5280[DISABLED] 5300[DISABLED] 5320[DISABLED] 5500[DISABLED]
nl80211: Mode IEEE 802.11b: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467[NO_IR] 2472[NO_IR] 2484[DISABLED]
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
Completing interface initialization
Mode: IEEE 802.11g Channel: 3 Frequency: 2422 MHz
DFS 0 channels required radar detection
nl80211: Set freq 2422 (ht_enabled=0, vht_enabled=0, he_enabled=0, bandwidth=20 MHz, cf1=2422 MHz, cf2=0 MHz)- freq=2422
- he_enabled=0
- vht_enabled=0
- ht_enabled=0
- channel_type=0
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0x1dfb060 (wlan0), first=1)
nl80211: flush -> DEL_STATION wlan0 (all)
Using interface wlan0 with hwaddr f0:c8:14:7b:5a:4b and ssid "hostapd_test"
Deriving WPA PSK based on passphrase
SSID - hexdump_ascii(len=12):
68 6f 73 74 61 70 64 5f 74 65 73 74 hostapd_test
PSK (ASCII passphrase) - hexdump_ascii(len=8): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
random: Got 20/20 random bytes
Get randomness: len=32 entropy=0
GMK - hexdump(len=32): [REMOVED]
Get randomness: len=32 entropy=0
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=63): 80 00 00 00 ff ff ff ff ff ff f0 c8 14 7b 5a 4b f0 c8 14 7b 5a 4b 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 0c 68 6f 73 74 61 70 64 5f 74 65 73 74 01 08 82 84 8b 96 0c 12 18 24 03 01 03
nl80211: Beacon tail - hexdump(len=35): 2a 01 04 32 04 30 48 60 6c 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 00 00
nl80211: ifindex=7
nl80211: beacon_int=100
nl80211: beacon_rate=0
nl80211: rate_type=0
nl80211: dtim_period=2
nl80211: ssid=hostapd_test - beacon_int=100
- dtim_period=2
nl80211: hidden SSID not in use
nl80211: privacy=2
nl80211: auth_algs=0x3
nl80211: wpa_version=0x2
nl80211: key_mgmt_suites=0x2
nl80211: pairwise_ciphers=0x18
nl80211: group_cipher=0x8
wlan0: Deauthenticate all stations at BSS start
nl80211: sta_remove -> DEL_STATION wlan0 ff:ff:ff:ff:ff:ff --> -22 (Invalid argument)
WPA: Start group state machine to set initial keys
WPA: group state machine entering state GTK_INIT (VLAN-ID 0)
Get randomness: len=32 entropy=0
GTK - hexdump(len=32): [REMOVED]
WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0)
wpa_driver_nl80211_set_key: ifindex=7 (wlan0) alg=2 addr=0x8560c key_idx=1 set_tx=1 seq_len=0 key_len=32 key_flag=0x1a
nl80211: NEW_KEY
nl80211: KEY_DATA - hexdump(len=32): [REMOVED]
broadcast key
nl80211: NL80211_CMD_SET_KEY - default key
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
nl80211: TX queue param set: queue=0 aifs=1 cw_min=3 cw_max=7 burst_time=15 --> res=-95
Failed to set TX queue parameters for queue 0.
nl80211: TX queue param set: queue=1 aifs=1 cw_min=7 cw_max=15 burst_time=30 --> res=-95
Failed to set TX queue parameters for queue 1.
nl80211: TX queue param set: queue=2 aifs=3 cw_min=15 cw_max=63 burst_time=0 --> res=-95
Failed to set TX queue parameters for queue 2.
nl80211: TX queue param set: queue=3 aifs=7 cw_min=15 cw_max=1023 burst_time=0 --> res=-95
Failed to set TX queue parameters for queue 3.
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
wlan0: Setup of interface done.
ctrl_iface not configured!
RTM_NEWLINK: ifi_index=7 ifname=wlan0 operstate=6 linkmode=0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Event message available
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station 78:62:56:c1:26:31
nl80211: Assoc Req IEs - hexdump(len=0): [NULL]
wlan0: Event ASSOC (0) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: associated
STA did not include WPS/RSN/WPA IE in (Re)AssocReq
New STA
ap_sta_add: register ap_handle_timer timeout for 78:62:56:c1:26:31 (300 seconds - ap_max_inactivity)
No WPA/RSN IE from STA
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
nl80211: Set STA flags - ifname=wlan0 addr=78:62:56:c1:26:31 total_flags=0x0 flags_or=0x0 flags_and=0xfffffff1 authorized=0
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
ap_free_sta: cancel ap_handle_timer for 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station 78:62:56:c1:26:31
wlan0: Event DISASSOC (1) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: disassociated
Disassociation notification for unknown STA 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station 78:62:56:c1:26:31
nl80211: Assoc Req IEs - hexdump(len=0): [NULL]
wlan0: Event ASSOC (0) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: associated
STA did not include WPS/RSN/WPA IE in (Re)AssocReq
New STA
ap_sta_add: register ap_handle_timer timeout for 78:62:56:c1:26:31 (300 seconds - ap_max_inactivity)
No WPA/RSN IE from STA
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
nl80211: Set STA flags - ifname=wlan0 addr=78:62:56:c1:26:31 total_flags=0x0 flags_or=0x0 flags_and=0xfffffff1 authorized=0
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
ap_free_sta: cancel ap_handle_timer for 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station 78:62:56:c1:26:31
wlan0: Event DISASSOC (1) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: disassociated
Disassociation notification for unknown STA 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station 78:62:56:c1:26:31
nl80211: Assoc Req IEs - hexdump(len=0): [NULL]
wlan0: Event ASSOC (0) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: associated
STA did not include WPS/RSN/WPA IE in (Re)AssocReq
New STA
ap_sta_add: register ap_handle_timer timeout for 78:62:56:c1:26:31 (300 seconds - ap_max_inactivity)
No WPA/RSN IE from STA
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
nl80211: Set STA flags - ifname=wlan0 addr=78:62:56:c1:26:31 total_flags=0x0 flags_or=0x0 flags_and=0xfffffff1 authorized=0
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
ap_free_sta: cancel ap_handle_timer for 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station 78:62:56:c1:26:31
wlan0: Event DISASSOC (1) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: disassociated
Disassociation notification for unknown STA 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0
nl80211: New station 78:62:56:c1:26:31
nl80211: Assoc Req IEs - hexdump(len=0): [NULL]
wlan0: Event ASSOC (0) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: associated
STA did not include WPS/RSN/WPA IE in (Re)AssocReq
New STA
ap_sta_add: register ap_handle_timer timeout for 78:62:56:c1:26:31 (300 seconds - ap_max_inactivity)
No WPA/RSN IE from STA
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
nl80211: Set STA flags - ifname=wlan0 addr=78:62:56:c1:26:31 total_flags=0x0 flags_or=0x0 flags_and=0xfffffff1 authorized=0
nl80211: sta_remove -> DEL_STATION wlan0 78:62:56:c1:26:31 --> 0 (Success)
ap_free_sta: cancel ap_handle_timer for 78:62:56:c1:26:31
nl80211: Event message available
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlan0
nl80211: Delete station 78:62:56:c1:26:31
wlan0: Event DISASSOC (1) received
wlan0: STA 78:62:56:c1:26:31 IEEE 802.11: disassociated
Disassociation notification for unknown STA 78:62:56:c1:26:31
-
回复: SPI转串口的问题发布在 Linux
@masterlu 多次收发123的结果是这样的，似乎每一次收发的时间都会比之前的要长一些。。。。
发送：
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0
sh-4.2# echo 123 > /dev/ttysWK0接收：
sh-4.2# cat /dev/ttysWK0
123123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
-
回复: 关于闭源文件的问题发布在 Linux
@xiaowenge 这是在A40i编译时出现的问题，文件是全志提供的，具体影响是当我打上实时补丁后编译会出现：
/home/golden/proj/KK-T3-SW/lichee/linux-3.10/drivers/char/awchip/awchip.c:44: undefined reference to `mutex_lock
另一种情况是我将编译工具替换为硬浮点进行编译后会出现类似：
uses VFP register arguments，
arm-linux-gnueabihf-ld: 合并目标文件 的特定数据时失败 -
回复: 关于闭源文件的问题发布在 Linux
@yuzukitsuru 比如A40i中的/lichee_A40i/linux-3.10/drivers/char/awchip/下的文件，我并不想要修改它，但是我做的修改确实会影响到它的编译。
-
A40i编译又报错了...发布在 编译和烧写问题专区
请大佬帮忙看看这个报错：
{standard input}: Assembler messages:
{standard input}:998: Error: selected processor does not supportvld2.8 {q0,q1},[r2]!' in ARM mode {standard input}:999: Error: selected processor does not supportvswp q0,q1' in ARM mode
{standard input}:1001: Error: selected processor does not supportvst2.8 {q0,q1},[r1]!' in ARM mode {standard input}:1008: Error: selected processor does not supportvld2.8 {d0,d1},[r2]!' in ARM mode
{standard input}:1009: Error: selected processor does not supportvswp d0,d1' in ARM mode {standard input}:1011: Error: selected processor does not supportvst2.8 {d0,d1},[r1]!' in ARM mode
{standard input}:1018: Error: selected processor does not supportvld2.8 {d0,d1},[r2]!' in ARM mode {standard input}:1019: Error: selected processor does not supportvswp d0,d1' in ARM mode
{standard input}:1021: Error: selected processor does not support `vst2.8 {d0[0],d1[0]},[r1]!' in ARM mode
Makefile_sub:131: recipe for target 'obj/camera/CallbackNotifier.o' failed文件在buildroot/target/user_rootfs_misc/sdk下
-
回复: 编译A40i时出现奇怪的错误发布在 Linux
@yuzukitsuru 我直接在Makefile里面把它去掉了，我不清楚是不是因为这个原因，编译出来的镜像会跑飞，所以我想尝试将这个问题解决。
另外，这个问题是在给A40i打实时补丁的时候遇到的，在补丁文件中已经有函数的定义以及实现，并且在其他文件中调用这个函数的时候并没有出现报错的情况，只是在awchip文件中出现了这个报错。 -
回复: 编译A40i时出现奇怪的错误发布在 Linux
@masterlu
在kernel/Makefile下有这样一段：
ifneq ($(CONFIG_PREEMPT_RT_FULL),y)
obj-y += mutex.o
obj-$(CONFIG_DEBUG_MUTEXES) += mutex-debug.o
obj-y += rwsem.o
endif
请问如果不编译mutex会不会影响其他功能？ -
编译A40i时出现奇怪的错误发布在 Linux
在编译A40i linux时出现了一个奇怪的错误，一个不存在的路径的下的文件编译报错了。
图中的/home/golden/proj/KK-T3-SW/,这个路径根本就不存在，请问有人遇到过吗？ -
回复: 如何修改A40i linux分区格式发布在 Linux
@whycan 是的。
根据boot-resource.ini中的format参数，可以看到为fat16，问题是这个参数没有办法设置为其他的格式，一旦修改就会打印下面的错误信息。
请问有什么办法解决吗？
