芒果派 MQ Pro,MQ 的板级配置文件
-
下载:
同时有D1-H与D1s的配置文件。
直接复制进 tina-d1-h 就可以了
实时更新仓库(上面那个tar不想打包了,之后更新丢github上)
-
好像发的是d1s的包?
-
多谢老板奉献!D1S也是用了你的patch文件编译的2.0tina
-
@feng_snail_aw 好像确实发错了,等我换一下((
-
@feng_snail_aw 修好了(((
-
@yuzukitsuru 我看d1的sdk里面make menuconfig里面有现成的gui选项,这种内置的gui/lvgl8可以直接编译跑起来么
-
@yelong98 没必要吧,直接交叉编译就行了,lvgl又不是qt要考虑gpl
-
MQ D1s 增加RTL8189FTV WiFi驱动,Github已经更新
-
-
-
-
-
-
@yuzukitsuru感谢大佬分享,我为麻雀编译了tina,用的最新的tina-d1-h,从git上clone了最新的补丁,编译打包正常,第一次开机时可以正常搜索到wifi
也可以正常连接,ping通
断电再次开机,就搜索不到任何wifi了,也连接不上了
一头雾水 麻烦大佬给看一下 -
@ggy321 有可能是wifi芯片损坏了,RTL8189的通病
-
@ggy321 检查USB 电源供电质量, 用好一点的电源。
另外自己做板的话, RTL的WIFI 模块要独立一个电源可控, 上电时不能有残电。 -
@ggy321
另外出错的时候把dmesg 贴上来,看下是否 主控无法读取到模块的EFUSE 信息。 -
@tevet 时好时坏的 又不行了 ,dmesg如下
root@TinaLinux:/# dmesg RTL871X: _rtw_pwr_wakeup call ips_leave.... RTL871X: ==>ips_leave cnts:5 RTL871X: ===> rtw_ips_pwr_up.............. RTL871X: ===> ips_netdrv_open......... RTL871X: FW does not exist before power on!! RTL871X: SetHwReg8188F: hci_sus_state=1 RTL871X: SetHwReg8188F: bMacPwrCtrlOn=1 RTL871X: SetHwReg8188F: hci_sus_state=2 RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same. RTL871X: PowerOnCheck: 0x1B8 test Pass. RTL871X: Power on ok! RTL871X: rtl8188f_FirmwareDownload(wlan0) tmp_ps=3 RTL871X: rtl8188f_FirmwareDownload fw: FW_NIC, size: 21020 RTL871X: rtl8188f_FirmwareDownload: fw_ver=4 fw_subver=0000 sig=0x88f1, Month=08, Date=22, Hour=17, Minute=36 RTL871X: rtl8188f_FirmwareDownload(): Shift for fw header! RTL871X: rtl8188f_FirmwareDownload by IO write! RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050505 RTL871X: _8051Reset8188: Finish RTL871X: _FWFreeToGo: Polling FW ready OK! (100, 20ms), REG_MCUFWDL:0x000505c6 RTL871X: rtl8188f_FirmwareDownload: DLFW OK ! RTL871X: rtl8188f_FirmwareDownload success. write_fw:1, 220ms RTL871X: <=== rtl8188f_FirmwareDownload() RTL871X: HalDetectPwrDownMode(): PDN=0 RTL871X: Set RF Chip ID to RF_6052 and RF type to 3. RTL871X: #### hw_var_set_opmode() -4815 iface_type(0) mode = 2 #### RTL871X: rtw_rf_get_kfree_tx_gain_offset path:0, ch:6, bb_gain_sel:0, kfree_offset:2 RTL871X: kfree gain_offset 0x55:0x82060 RTL871X: after :0x8a060 RTL871X: <=== rtw_ips_pwr_up.............. in 710ms RTL871X: nolinked power save leave RTL871X: ==> ips_leave.....LED(0x01028282)... RTL871X: survey done event(0) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) RTL871X: ==>rtw_ps_processor .fw_state(8) RTL871X: ==>ips_enter cnts:6 RTL871X: nolinked power save enter RTL871X: ===> rtw_ips_pwr_down................... RTL871X: ====> rtw_ips_dev_unload... RTL871X: SetHwReg8188F: bMacPwrCtrlOn=0 RTL871X: SetHwReg8188F: hci_sus_state=3 RTL871X: SetHwReg8188F: hci_sus_state=0 RTL871X: <=== rtw_ips_pwr_down..................... in 10ms RTL871X: cfg80211_rtw_scan(wlan0) RTL871X: _rtw_pwr_wakeup call ips_leave.... RTL871X: ==>ips_leave cnts:6 RTL871X: ===> rtw_ips_pwr_up.............. RTL871X: ===> ips_netdrv_open......... RTL871X: FW does not exist before power on!! RTL871X: SetHwReg8188F: hci_sus_state=1 RTL871X: SetHwReg8188F: bMacPwrCtrlOn=1 RTL871X: SetHwReg8188F: hci_sus_state=2 RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same. RTL871X: PowerOnCheck: 0x1B8 test Pass. RTL871X: Power on ok! RTL871X: rtl8188f_FirmwareDownload(wlan0) tmp_ps=3 RTL871X: rtl8188f_FirmwareDownload fw: FW_NIC, size: 21020 RTL871X: rtl8188f_FirmwareDownload: fw_ver=4 fw_subver=0000 sig=0x88f1, Month=08, Date=22, Hour=17, Minute=36 RTL871X: rtl8188f_FirmwareDownload(): Shift for fw header! RTL871X: rtl8188f_FirmwareDownload by IO write! RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050505 RTL871X: _8051Reset8188: Finish RTL871X: _FWFreeToGo: Polling FW ready OK! (107, 10ms), REG_MCUFWDL:0x000505c6 RTL871X: rtl8188f_FirmwareDownload: DLFW OK ! RTL871X: rtl8188f_FirmwareDownload success. write_fw:1, 220ms RTL871X: <=== rtl8188f_FirmwareDownload() RTL871X: HalDetectPwrDownMode(): PDN=0 RTL871X: Set RF Chip ID to RF_6052 and RF type to 3. RTL871X: #### hw_var_set_opmode() -4815 iface_type(0) mode = 2 #### RTL871X: rtw_rf_get_kfree_tx_gain_offset path:0, ch:6, bb_gain_sel:0, kfree_offset:2 RTL871X: kfree gain_offset 0x55:0x82060 RTL871X: after :0x8a060 RTL871X: <=== rtw_ips_pwr_up.............. in 760ms RTL871X: nolinked power save leave RTL871X: ==> ips_leave.....LED(0x01028282)... RTL871X: survey done event(0) band:0 for wlan0 RTL871X: rtw_indicate_scan_done(wlan0) RTL871X: ==>rtw_ps_processor .fw_state(8) RTL871X: ==>ips_enter cnts:7 RTL871X: nolinked power save enter RTL871X: ===> rtw_ips_pwr_down................... RTL871X: ====> rtw_ips_dev_unload... RTL871X: SetHwReg8188F: bMacPwrCtrlOn=0 RTL871X: SetHwReg8188F: hci_sus_state=3 RTL871X: SetHwReg8188F: hci_sus_state=0 RTL871X: <=== rtw_ips_pwr_down..................... in 10ms RTL871X: cfg80211_rtw_scan(wlan0) RTL871X: _rtw_pwr_wakeup call ips_leave.... RTL871X: ==>ips_leave cnts:7 RTL871X: ===> rtw_ips_pwr_up.............. RTL871X: ===> ips_netdrv_open......... RTL871X: FW does not exist before power on!! RTL871X: SetHwReg8188F: hci_sus_state=1 RTL871X: SetHwReg8188F: bMacPwrCtrlOn=1 RTL871X: SetHwReg8188F: hci_sus_state=2 RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same. RTL871X: PowerOnCheck: 0x1B8 test Pass. RTL871X: Power on ok! RTL871X: rtl8188f_FirmwareDownload(wlan0) tmp_ps=3 RTL871X: rtl8188f_FirmwareDownload fw: FW_NIC, size: 21020 RTL871X: rtl8188f_FirmwareDownload: fw_ver=4 fw_subver=0000 sig=0x88f1, Month=08, Date=22, Hour=17, Minute=36 RTL871X: rtl8188f_FirmwareDownload(): Shift for fw header! RTL871X: rtl8188f_FirmwareDownload by IO write! RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050505 RTL871X: _8051Reset8188: Finish RTL871X: _FWFreeToGo: Polling FW ready OK! (100, 20ms), REG_MCUFWDL:0x000505c6 RTL871X: rtl8188f_FirmwareDownload: DLFW OK ! RTL871X: rtl8188f_FirmwareDownload success. write_fw:1, 230ms RTL871X: <=== rtl8188f_FirmwareDownload() RTL871X: HalDetectPwrDownMode(): PDN=0 RTL871X: Set RF Chip ID to RF_6052 and RF type to 3. RTL871X: #### hw_var_set_opmode() -4815 iface_type(0) mode = 2 #### RTL871X: rtw_rf_get_kfree_tx_gain_offset path:0, ch:6, bb_gain_sel:0, kfree_offset:2 RTL871X: kfree gain_offset 0x55:0x82060 RTL871X: after :0x8a060 RTL871X: <=== rtw_ips_pwr_up.............. in 720ms RTL871X: nolinked power save leave RTL871X: ==> ips_leave.....LED(0x01028282)...
-
@yuzukitsuru 在 芒果派 MQ Pro,MQ 的板级配置文件 中说:
下载:
同时有D1-H与D1s的配置文件。
直接复制进 tina-d1-h 就可以了
实时更新仓库(上面那个tar不想打包了,之后更新丢github上)
这个配置文件,针对 的是这个sdk?覆盖这个sdk的文件即可是吧~~
① 官方SDK下载: https://d1.docs.aw-ol.com/study/study_2getsdk/
② 骚操作下载:
百度分享: https://pan.baidu.com/s/1QjHPLrWIRQMUb7sr4eBd-g
提取码: 6666
解压密码: whycan.commd5校验码:
b6a41b47dfccad249ba7b40c5d195717 *d1_sdk.tar.zip.001
1e31cded2fc9f8c602a28fbf63449e8a *d1_sdk.tar.zip.002
9e4cdb935e4ae8b775586bb25505e33a *d1_sdk.tar.zip.003 -
MQ Pro接DSI屏,打patch,编译镜像,烧写后开机,屏有背光,但运行lv_example没有显示,cat /dev/urandom > /dev/fb0也没有。查了屏的芯片是ST7701,kernel里也编了驱动。有何解决思路?
Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号