Navigation

    全志在线开发者论坛

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • 在线文档
    • 社区主页

    Porject Yosemite - 基于全志V853的开发板

    V Series
    18
    55
    22082
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • YuzukiTsuru
      柚木 鉉 LV 9 last edited by q1215200171

      f69fe400-e04a-4610-8980-0c5473469eae-image.png

      • V853 ARM A7 + RISC-V E907 + 1T NPU
      • UP to 2GiB DDR3 and 128GiB EMMC
      • Raspberry Pi Camera Connector
      • 2 lane MIPI-CSI
      • 4 lane MIPI-DSI up to 1920x1200
      • Built-in USB to UART Support RV and ARM
      • Built-in XR829 Wi-Fi BT
      • Raspberry Pi A Size and Pinout

      6db867e7-6a0c-4b0f-9aac-4aba458b1c72-image.png

      开源地址:https://oshwhub.com/gloomyghost/porject-yosemite

      This is a high-performance heterogeneous edge AI visual processing core development board based on Allwinner V853 - Porject Yosemite. Allwinner V853 supports simultaneous heterogeneous debugging of Arm and RISC-V cores, with 1Tops NPU, and supports TensorFlow, Caffe, Tflite, Python, Onnx NN and other models.

      The development board design adopts the Raspberry Pi A version, with a 40Pin IO output and a MIPI DSI screen interface, supporting up to 1920x1200 resolution MIPI screens and capacitive touch.

      Y 1 Reply Last reply Reply Quote Share 5
      • Y
        yelong98 LV 7 @YuzukiTsuru last edited by

        @yuzukitsuru 强顶,调通了我也想买一块玩下,跟一跟AI的潮流,不然落伍太多了

        1 Reply Last reply Reply Quote Share 0
        • Y
          yelong98 LV 7 last edited by

          我感觉你这块会比芒果的出来的更快,船小好掉头

          1 Reply Last reply Reply Quote Share 0
          • xiaowenge
            DOT小文哥 LV 8 last edited by

            我瞅瞅,
            主控V853,DDR、存储、网口芯片、两个USB、mipi-csi、camera、一大串插针排线,还有的是啥

            Y 1 Reply Last reply Reply Quote Share 0
            • Y
              yelong98 LV 7 @xiaowenge last edited by

              @xiaowenge 小文哥,sdk啥时候释放啊,新妓到来,饥渴难耐啊

              xiaowenge 1 Reply Last reply Reply Quote Share 0
              • xiaowenge
                DOT小文哥 LV 8 @yelong98 last edited by

                @yelong98 在 Porject Yosemite - 基于全志V853 中说:

                @xiaowenge 小文哥,sdk啥时候释放啊,新妓到来,饥渴难耐啊

                快了,在mkdir v853_sdk 了

                1 Reply Last reply Reply Quote Share 1
                • YuzukiTsuru
                  柚木 鉉 LV 9 last edited by

                  稍稍布线下

                  e322a097-e4f8-4e11-8c7a-3588e69cc196-ased.png

                  1 Reply Last reply Reply Quote Share 0
                  • YuzukiTsuru
                    柚木 鉉 LV 9 last edited by YuzukiTsuru

                    8f8c49c7-1cc9-4730-aad1-e151a57c229a-image.png
                    8bit的不多见哦

                    Y 1 Reply Last reply Reply Quote Share 0
                    • Y
                      yelong98 LV 7 @YuzukiTsuru last edited by

                      @yuzukitsuru 来个完整的看看

                      1 Reply Last reply Reply Quote Share 0
                      • YuzukiTsuru
                        柚木 鉉 LV 9 last edited by

                        emmc也并网了

                        ceac1273-9a98-4fb2-a049-fb93d09ecc8f-image.png

                        1 Reply Last reply Reply Quote Share 3
                        • J
                          jiangh LV 3 last edited by

                          整个粉色,才能吸引猛男围观

                          YuzukiTsuru 1 Reply Last reply Reply Quote Share 0
                          • YuzukiTsuru
                            柚木 鉉 LV 9 @jiangh last edited by

                            @jiangh 没钱打啊

                            1 Reply Last reply Reply Quote Share 0
                            • Y
                              yelong98 LV 7 last edited by

                              等着放原理图准备抄作业

                              A 1 Reply Last reply Reply Quote Share 0
                              • A
                                a937983423 LV 4 @yelong98 last edited by

                                @yelong98 自己做比买贵多了

                                Y 1 Reply Last reply Reply Quote Share 0
                                • Y
                                  yelong98 LV 7 @a937983423 last edited by

                                  @a937983423 那是必然的,这不是现在还买不到么

                                  tigger 1 Reply Last reply Reply Quote Share 0
                                  • tigger
                                    tigger LV 7 @yelong98 last edited by

                                    @yelong98
                                    学渣过来强行解释一下,自己做因为边际成本太高。

                                    1 Reply Last reply Reply Quote Share 0
                                    • YuzukiTsuru
                                      柚木 鉉 LV 9 last edited by

                                      WiFi,CSI,RCSI上线了
                                      f42b2448-5847-4926-b717-e4cccd992120-image.png

                                      1 Reply Last reply Reply Quote Share 2
                                      • YuzukiTsuru
                                        柚木 鉉 LV 9 last edited by

                                        基本完工,再优化下走线

                                        6d4fba50-d5bf-42ed-8def-709d290854db-image.png

                                        Y 1 Reply Last reply Reply Quote Share 0
                                        • Y
                                          yelong98 LV 7 @YuzukiTsuru last edited by

                                          @yuzukitsuru 老板威武,比原厂速度快

                                          YuzukiTsuru 1 Reply Last reply Reply Quote Share 0
                                          • YuzukiTsuru
                                            柚木 鉉 LV 9 @yelong98 last edited by

                                            @yelong98 咋可能,就是参考原厂的画出来的

                                            X 1 Reply Last reply Reply Quote Share 0
                                            • YuzukiTsuru
                                              柚木 鉉 LV 9 last edited by

                                              3D_PCB1_2022-05-17.png

                                              1 Reply Last reply Reply Quote Share 0
                                              • YuzukiTsuru
                                                柚木 鉉 LV 9 last edited by

                                                5f47ba16-3c72-4cb3-8b85-a81ab688aaf6-3D_PCB1_2022-05-17.png

                                                1 Reply Last reply Reply Quote Share 2
                                                • W
                                                  wsxiaoping3 LV 2 last edited by xiaowenge

                                                  更新很快啊,不错!

                                                  1 Reply Last reply Reply Quote Share 0
                                                  • YuzukiTsuru
                                                    柚木 鉉 LV 9 last edited by

                                                    下单了,试试华秋的

                                                    34b63435-61f6-445c-91e4-9f169fcd482f-image.png

                                                    1 Reply Last reply Reply Quote Share 1
                                                    • YuzukiTsuru
                                                      柚木 鉉 LV 9 last edited by

                                                      板子到货了

                                                      b4f30ddd-017d-4a54-83f8-6f9b7d366985-b184f9e61de001a835439b5ab7a03b7.jpg

                                                      8af3e17d-e7b6-4e69-aa62-6ee9c40b8c24-173a883221033547b3d0e24b23a74c6.jpg

                                                      1 Reply Last reply Reply Quote Share 1
                                                      • YuzukiTsuru
                                                        柚木 鉉 LV 9 last edited by

                                                        稍微焊接了一下下

                                                        11383c67-a66b-4354-97cd-91892f235d53-301de98ee44a2ac06333b05594976da.jpg

                                                        5b5ecac1-6c94-4539-9d51-430e7e944e69-e4a66a54658144cc37549dc78f4d019.jpg

                                                        ed84e7fa-2f1a-45dc-8982-f1220d703a5d-27dc5bc3c2b255c1d4f0b54451f2078.jpg

                                                        F 1 Reply Last reply Reply Quote Share 2
                                                        • X
                                                          卷心菜 LV 3 @YuzukiTsuru last edited by

                                                          @yuzukitsuru 大佬,弱弱的问一下,,原厂是在哪里参考的,我去全志的技术支持平台也没找到https://open.allwinnertech.com/#/
                                                          莫非个人是拿不到相关资料了吗😿

                                                          YuzukiTsuru 1 Reply Last reply Reply Quote Share 0
                                                          • YuzukiTsuru
                                                            柚木 鉉 LV 9 @XueYu last edited by

                                                            @xueyu 耐心等待下,相关资料之后会放出来的,这个板子也会完全开源的

                                                            X 1 Reply Last reply Reply Quote Share 1
                                                            • X
                                                              卷心菜 LV 3 @YuzukiTsuru last edited by

                                                              @YuzukiTsuru 向大佬致敬,👌

                                                              1 Reply Last reply Reply Quote Share 0
                                                              • F
                                                                fawen LV 5 @YuzukiTsuru last edited by

                                                                @yuzukitsuru 可以到哪里买到吗?

                                                                YuzukiTsuru 1 Reply Last reply Reply Quote Share 0
                                                                • YuzukiTsuru
                                                                  柚木 鉉 LV 9 last edited by

                                                                  4070eb5b-216b-4109-81bf-d59a215d3b20-a.jpg

                                                                  1 Reply Last reply Reply Quote Share 1
                                                                  • YuzukiTsuru
                                                                    柚木 鉉 LV 9 @fawen last edited by

                                                                    @fawen 大概是没有钱钱量产的,要的多可以考虑众筹下(?

                                                                    L J 2 Replies Last reply Reply Quote Share 2
                                                                    • L
                                                                      lloovve LV 3 @YuzukiTsuru last edited by

                                                                      @yuzukitsuru 支持众筹,非常期待

                                                                      F 1 Reply Last reply Reply Quote Share 0
                                                                      • J
                                                                        jordonwu LV 6 @YuzukiTsuru last edited by

                                                                        @yuzukitsuru
                                                                        可以搞个预付部分众筹

                                                                        1 Reply Last reply Reply Quote Share 0
                                                                        • F
                                                                          fawen LV 5 @lloovve last edited by

                                                                          @lloovve 支持众筹,我想站对

                                                                          1 Reply Last reply Reply Quote Share 0
                                                                          • YuzukiTsuru
                                                                            柚木 鉉 LV 9 last edited by

                                                                            启动了!内存没啥大问题了

                                                                            [26182]fes begin commit:fbe7448cdb
                                                                            [26185]set pll start
                                                                            [26187]periph0 has been enabled
                                                                            [26190]set pll end
                                                                            [26193]PMU: AXP21
                                                                            [26196]board init ok
                                                                            [26198]beign to init dram
                                                                            [26200]DRAM use external ZQ!!
                                                                            [26203]chip id check OK
                                                                            [26206]DRAM_VCC set to 1500 mv
                                                                            [26209]trefi:7.8ms
                                                                            [26211][AUTO DEBUG] single rank and full DQ!
                                                                            [26216]trefi:7.8ms
                                                                            [26218][AUTO DEBUG] rank 0 row = 15 
                                                                            [26222][AUTO DEBUG] rank 0 bank = 8 
                                                                            [26225][AUTO DEBUG] rank 0 page size = 2 KB 
                                                                            [26229]DRAM BOOT DRIVE INFO: V0.16
                                                                            [26232]DRAM CLK = 936 MHz
                                                                            [26235]DRAM Type = 3 (2:DDR2,3:DDR3)
                                                                            [26238]DRAMC ZQ value: 0x7b7bfb
                                                                            [26241]DRAM ODT value: 0x42.
                                                                            [26245]DRAM SIZE =512 M
                                                                            [26247]dram_tpr4:0x0
                                                                            [26250]DRAM simple test OK.
                                                                            [26253]rtc standby flag is 0x0, super standby flag is 0x0
                                                                            [26258]init dram ok
                                                                            
                                                                            
                                                                            
                                                                            U-Boot 2018.05-00006-gb5e4c9f6fb (Jun 09 2022 - 06:47:31 +0000) Allwinner Technology
                                                                            
                                                                            [27.808]CPU:   Allwinner Family
                                                                            [27.811]Model: sun8iw21
                                                                            I2C:   ready
                                                                            [27.837]DRAM:  512 MiB
                                                                            [27.840]Relocation Offset is: 1ced0000
                                                                            [27.865]secure enable bit: 0
                                                                            [27.867]PMU: AXP21
                                                                            [27.869]PMU: pmu_axp2101 found
                                                                            [27.872]BMU: AXP21
                                                                            [27.874]BMU: bmu_axp2101 found
                                                                            FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_INTERNAL
                                                                            [27.884]gpio_bias, pc_bias: 1800, pc_supply: not set  
                                                                            [27.889]gpio_bias, pl_bias:   -1, pl_supply: not set  
                                                                            [27.895]dcdc1_vol = 3300, onoff=1
                                                                            [27.898]dcdc2_vol = 900, onoff=1
                                                                            [27.901]dcdc5_vol = 0, onoff=0
                                                                            [27.905]aldo1_vol = 1800, onoff=1
                                                                            [27.908]aldo2_vol = 1800, onoff=1
                                                                            [27.912]aldo3_vol = 3300, onoff=1
                                                                            [27.915]aldo4_vol = 3300, onoff=1
                                                                            [27.919]bldo1_vol = 1800, onoff=1
                                                                            [27.922]bldo2_vol = 2800, onoff=1
                                                                            [27.926]dldo1_vol = 3300, onoff=1
                                                                            [27.929]dldo2_vol = 1200, onoff=1
                                                                            bias_name:pc_bias	 bias_vol:1800
                                                                            bias_name:pi_bias	 bias_vol:1800
                                                                            [27.939]bat_vol=4577, ratio=1
                                                                            [27.942]safe_vol=3500, safe_ratio=1
                                                                            [27.946]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz  MBus=300Mhz
                                                                            [27.952]gic: normal mode
                                                                            sunxi flash map init
                                                                            [27.957]flash init start
                                                                            [27.959]workmode = 16,storage type = 0
                                                                            try card 2
                                                                            set card number 2
                                                                            get card number 2
                                                                            [27.967][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
                                                                            [27.972][mmc]: get sdc_type fail and use default host:tm4.
                                                                            [27.979][mmc]: Is not Boot mode!
                                                                            [27.982][mmc]: SUNXI SDMMC Controller Version:0x50400
                                                                            [27.993][mmc]: ************Try SD card 2************
                                                                            [27.998][mmc]: mmc 2 cmd timeout 100 status 100
                                                                            [28.002][mmc]: smc 2 err, cmd 8,  RTO
                                                                            [28.006][mmc]: mmc 2 close bus gating and reset
                                                                            [28.011][mmc]: mmc 2 cmd timeout 100 status 100
                                                                            [28.015][mmc]: smc 2 err, cmd 55,  RTO
                                                                            [28.018][mmc]: mmc 2 close bus gating and reset
                                                                            [28.023][mmc]: ************Try MMC card 2************
                                                                            
                                                                            [28.079][mmc]: mmc 2 cmd timeout 100 status 100
                                                                            [28.083][mmc]: smc 2 err, cmd 8,  RTO
                                                                            [28.086][mmc]: mmc 2 close bus gating and reset
                                                                            [28.091][mmc]: mmc 2 cmd timeout 100 status 100
                                                                            [28.095][mmc]: smc 2 err, cmd 55,  RTO
                                                                            [28.099][mmc]: mmc 2 close bus gating and reset
                                                                            [28.115][mmc]: gen_tuning_blk_bus8: total blk 10
                                                                            [28.119][mmc]: gen_tuning_blk_bus4: total blk 6
                                                                            [28.124][mmc]: Using 8 bit tuning now
                                                                            [28.127][mmc]: send stop
                                                                            [28.129][mmc]:  Write tuning pattern failded
                                                                            [28.133][mmc]: Using 8 bit tuning now
                                                                            [28.137][mmc]: send stop
                                                                            [28.139][mmc]:  Write tuning pattern failded
                                                                            
                                                                            [28.143][mmc]: Write pattern failed
                                                                            [28.146][mmc]: mmc init product failed
                                                                            MMC init failed
                                                                            try emmc fail
                                                                            [28.153]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106
                                                                            [28.158]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217
                                                                            [28.167]sunxi-spinand-phy: request spi0 gpio ok
                                                                            [28.171]sunxi-spinand-phy: request general tx dma channel ok!
                                                                            [28.176]sunxi-spinand-phy: request general rx dma channel ok!
                                                                            [28.182]sunxi-spinand-phy: set spic0 clk to 20 Mhz
                                                                            [28.186]sunxi-spinand-phy: init spic0 clk ok
                                                                            [29.190]sunxi-spinand-phy: read id failed : -110
                                                                            try nand fail
                                                                            [29.198]unrecognized JEDEC id bytes: ff, ff, ff
                                                                            data abort
                                                                            pc : [<5ff0b602>]	   lr : [<5ff0b5e9>]
                                                                            reloc pc : [<4303b602>]	   lr : [<4303b5e9>]
                                                                            sp : 5de6dc38  ip : 0000000c	 fp : 43000508
                                                                            r10: 43031ca1  r9 : 5deafe70	 r8 : 5deff8a8
                                                                            r7 : 5ff7f2e8  r6 : ffffffed	 r5 : 5ff4fbe0  r4 : 5deff8f0
                                                                            r3 : 00002000  r2 : 00000001	 r1 : 0000000a  r0 : 00000030
                                                                            Flags: nZCv  IRQs on  FIQs off  Mode SVC_32
                                                                            
                                                                            YuzukiTsuru 1 Reply Last reply Reply Quote Share 0
                                                                            • YuzukiTsuru
                                                                              柚木 鉉 LV 9 @YuzukiTsuru last edited by

                                                                              @yuzukitsuru
                                                                              内存跑到了1866

                                                                              D 1 Reply Last reply Reply Quote Share 0
                                                                              • D
                                                                                dream LV 6 @YuzukiTsuru last edited by

                                                                                @yuzukitsuru 666,1866 问题不大了

                                                                                1 Reply Last reply Reply Quote Share 0
                                                                                • YuzukiTsuru
                                                                                  柚木 鉉 LV 9 last edited by YuzukiTsuru

                                                                                  发一个内存模板

                                                                                  测试DDR3 1866没问题,PCB是从LCEDA导出的,JLC打板子选择2313

                                                                                  V853_DRAM.pcbdoc

                                                                                  注意:

                                                                                  1. 因格式和图元的设计不一致,格式转换会有一定的差异,导出后请务必在 Altium Designer 仔细检查。
                                                                                  2. 导出前请务必阅读: 导出 Altium Designer注意事项与免责声明
                                                                                  3. 不承担因导出差异导致的任何生产损失。
                                                                                  1 Reply Last reply Reply Quote Share 2
                                                                                  • YuzukiTsuru
                                                                                    柚木 鉉 LV 9 last edited by

                                                                                    验证了:

                                                                                    • DDR3 1866
                                                                                    • TF挂载
                                                                                    • eMMC启动
                                                                                    • GPIO使用
                                                                                    • i2c、spi功能
                                                                                    • UART转接芯片

                                                                                    WiFi还有问题,SDIO扫不到卡:https://bbs.aw-ol.com/topic/1675/share/1

                                                                                    61d16011-6feb-4973-946f-a49a1ab6475d-image.png

                                                                                    1 Reply Last reply Reply Quote Share 1
                                                                                    • YuzukiTsuru
                                                                                      柚木 鉉 LV 9 last edited by

                                                                                      验证了 MIPI-DSI,MIPI-CSI,现有问题:PMU在RST时下电不完全,不过不影响系统

                                                                                      7a6bd679-2e2f-4955-9e9d-0004dce631a2-image.png

                                                                                      树莓派山寨摄像头驱动:ov5647_mipi.c

                                                                                      1 Reply Last reply Reply Quote Share 0
                                                                                      • Referenced by  q1215200171 q1215200171 
                                                                                      • Referenced by  q1215200171 q1215200171 
                                                                                      • Referenced by  q1215200171 q1215200171 
                                                                                      • Referenced by  q1215200171 q1215200171 
                                                                                      • Referenced by  q1215200171 q1215200171 
                                                                                      • Referenced by  bayche bayche 
                                                                                      • Referenced by  bayche bayche 
                                                                                      • Referenced by  bayche bayche 
                                                                                      • Referenced by  bayche bayche 
                                                                                      • Referenced by  bayche bayche 
                                                                                      • YuzukiTsuru
                                                                                        柚木 鉉 LV 9 last edited by

                                                                                        项目文件:
                                                                                        bcbb006b-a850-4185-832b-8096ca195f40-yosemite_0.5.tar.gz

                                                                                        需要配合Tina 5.0使用

                                                                                        whycan 1 Reply Last reply Reply Quote Share 1
                                                                                        • whycan
                                                                                          whycan晕哥 LV 9 @YuzukiTsuru last edited by whycan

                                                                                          @yuzukitsuru
                                                                                          033a5de4-b081-461e-8a9a-34aa4f1fe71d-image.png

                                                                                          解压OK,正在编译,烧录进去请问ov5647_mipi 摄像头可以用吗?

                                                                                          whycan 1 Reply Last reply Reply Quote Share 0
                                                                                          • whycan
                                                                                            whycan晕哥 LV 9 @whycan last edited by

                                                                                            @whycan

                                                                                            make[3]: Entering directory '/opt/V85x/tina-v853-open/openwrt/openwrt/package/firmware/prism54-firmware'
                                                                                            make[3]: Nothing to be done for 'compile'.
                                                                                            make[3]: Leaving directory '/opt/V85x/tina-v853-open/openwrt/openwrt/package/firmware/prism54-firmware'
                                                                                            time: package/firmware/prism54-firmware/compile#0.11#0.04#0.14
                                                                                            make[3]: Entering directory '/opt/V85x/tina-v853-open/openwrt/openwrt/package/kernel/linux'
                                                                                            mkdir -p /opt/V85x/tina-v853-open/openwrt/openwrt/staging_dir/target/root-v853-yosemite/stamp
                                                                                            
                                                                                            SHELL= flock /opt/V85x/tina-v853-open/openwrt/openwrt/tmp/.root-copy.flock -c 'cp -fpR /opt/V85x/tina-v853-open/out/v853/yosemite/openwrt/build_dir/target/linux-v853-yosemite/packages/.pkgdir/kernel/. /opt/V85x/tina-v853-open/openwrt/openwrt/staging_dir/target/root-v853-yosemite/'
                                                                                            touch /opt/V85x/tina-v853-open/openwrt/openwrt/staging_dir/target/root-v853-yosemite/stamp/.kernel_installed
                                                                                            ERROR: module '/opt/V85x/tina-v853-open/out/v853/yosemite/openwrt/build_dir/target/linux-v853-yosemite/linux-4.9/drivers/media/platform/sunxi-vin/modules/sensor/ov5648_mipi.ko' is missing.
                                                                                            /opt/V85x/tina-v853-open/openwrt/openwrt/target/linux/v853-yosemite/modules.mk:29: recipe for target '/opt/V85x/tina-v853-open/out/v853/yosemite/openwrt/extra/targets/v853-yosemite/generic/packages/kmod-vin-v4l2_4.9-1_arm_cortex-a7_neon.ipk' failed
                                                                                            make[3]: *** [/opt/V85x/tina-v853-open/out/v853/yosemite/openwrt/extra/targets/v853-yosemite/generic/packages/kmod-vin-v4l2_4.9-1_arm_cortex-a7_neon.ipk] Error 1
                                                                                            make[3]: Leaving directory '/opt/V85x/tina-v853-open/openwrt/openwrt/package/kernel/linux'
                                                                                            time: package/kernel/linux/compile#1.16#0.07#1.24
                                                                                                ERROR: package/kernel/linux failed to build.
                                                                                            package/Makefile:114: recipe for target 'package/kernel/linux/compile' failed
                                                                                            make[2]: *** [package/kernel/linux/compile] Error 1
                                                                                            make[2]: Leaving directory '/opt/V85x/tina-v853-open/openwrt/openwrt'
                                                                                            package/Makefile:110: recipe for target '/opt/V85x/tina-v853-open/openwrt/openwrt/staging_dir/target/stamp/.package_compile' failed
                                                                                            make[1]: *** [/opt/V85x/tina-v853-open/openwrt/openwrt/staging_dir/target/stamp/.package_compile] Error 2
                                                                                            make[1]: Leaving directory '/opt/V85x/tina-v853-open/openwrt/openwrt'
                                                                                            /opt/V85x/tina-v853-open/openwrt/openwrt/include/toplevel.mk:236: recipe for target 'world' failed
                                                                                            make: *** [world] Error 2
                                                                                            make: Leaving directory '/opt/V85x/tina-v853-open/openwrt/openwrt'
                                                                                            INFO: build_openwrt_rootfs failed
                                                                                            

                                                                                            翻车了,补丁包还缺 ov5648_mipi.c ,麻烦楼主有空更新一下补丁包。

                                                                                            YuzukiTsuru 1 Reply Last reply Reply Quote Share 0
                                                                                            • YuzukiTsuru
                                                                                              柚木 鉉 LV 9 @whycan last edited by

                                                                                              @whycan
                                                                                              https://bbs.aw-ol.com/topic/1389/share/41

                                                                                              这里有驱动了

                                                                                              whycan M 2 Replies Last reply Reply Quote Share 0
                                                                                              • Referenced by  YuzukiTsuru YuzukiTsuru 
                                                                                              • whycan
                                                                                                whycan晕哥 LV 9 @YuzukiTsuru last edited by

                                                                                                @yuzukitsuru

                                                                                                project kernel/linux-4.9/                      
                                                                                                 -m     drivers/media/platform/sunxi-vin/modules/sensor/Kconfig
                                                                                                 -m     drivers/media/platform/sunxi-vin/modules/sensor/Makefile
                                                                                                

                                                                                                还要修改这两个文件才行

                                                                                                1 Reply Last reply Reply Quote Share 0
                                                                                                • M
                                                                                                  memory LV 7 @YuzukiTsuru last edited by

                                                                                                  @yuzukitsuru
                                                                                                  b3fdb07e-504a-49d9-9cb4-a388b1154f5a-image.png

                                                                                                  感谢感谢,烧录OK,运行成功.

                                                                                                  1 Reply Last reply Reply Quote Share 0
                                                                                                  • YuzukiTsuru
                                                                                                    柚木 鉉 LV 9 last edited by

                                                                                                    94ad43bd-4721-4ad4-978f-c3d034945df2-108046a5428ed19855284cca758073e.jpg

                                                                                                    DCDC 方案,验证通过

                                                                                                    1 Reply Last reply Reply Quote Share 0
                                                                                                    • F
                                                                                                      flytianya2010 LV 2 last edited by

                                                                                                      @whycan 晕哥,您这个板子我打样了,要如何烧录呢,制作了启动卡插上去没啥反应。具体什么刷固件呢。谢谢了。

                                                                                                      1 Reply Last reply Reply Quote Share 0
                                                                                                      • Y
                                                                                                        yifi2002 LV 1 last edited by

                                                                                                        感觉很好的,想要下载看看

                                                                                                        1 Reply Last reply Reply Quote Share 0
                                                                                                        • H
                                                                                                          别打了,我学 LV 5 last edited by

                                                                                                          翻车了😧 dcdc方案,驱动摄像头无限重启。是mp2122输出功率不够吗😧

                                                                                                          WhycanService 1 Reply Last reply Reply Quote Share 0
                                                                                                          • WhycanService
                                                                                                            WhycanService LV 8 @haolisheng last edited by

                                                                                                            @haolisheng 摄像头是3v3上拉了吗,PA域是1.8v的上拉3.3v会重启

                                                                                                            H 3 Replies Last reply Reply Quote Share 0
                                                                                                            • H
                                                                                                              别打了,我学 LV 5 @WhycanService last edited by

                                                                                                              This post is deleted!
                                                                                                              1 Reply Last reply Reply Quote Share 0
                                                                                                              • H
                                                                                                                别打了,我学 LV 5 @WhycanService last edited by

                                                                                                                This post is deleted!
                                                                                                                1 Reply Last reply Reply Quote Share 0
                                                                                                                • H
                                                                                                                  别打了,我学 LV 5 @WhycanService last edited by

                                                                                                                  @whycanservice 请教了下 yuzu佬,驱动寨厂的摄像头,需要PA域改供电3.3。感谢两位

                                                                                                                  1 Reply Last reply Reply Quote Share 0
                                                                                                                  • Referenced by  A awwwwa 
                                                                                                                  • 1 / 1
                                                                                                                  • First post
                                                                                                                    Last post

                                                                                                                  Copyright © 2024 深圳全志在线有限公司 粤ICP备2021084185号 粤公网安备44030502007680号

                                                                                                                  行为准则 | 用户协议 | 隐私权政策