我的运行不起来，NOR FLASH问题吗？？
[141]HELLO! BOOT0 is starting!
[144]BOOT0 commit : 889f614
sbi2ekernel
| /'_/\ (_ ) _ ( )( ) /' _\ /' \ | | | __ | | (_) ___ ______ _ _ | || | | ( ) | | ( ) | | | (_) | /'__\ | | | |/',
)()( ) ( )| || | | | | | | | | |
| | | | |( / | | | |_, \ | _/ |( ,) _ | () | _ | () |
| () ()\____)(___)(_)(____/ _
/' () ()\___/'(_)_/'
|version : V3.9.0|
|commitid: a850c7b6b408b36ea58bcce024f7c788688ca5ab|
|sunxiver: 40000|
|timever : Fri, 10 May 2024 02:41:39 -0700|
|compiler: gcc version 8.4.0 (T-HEAD RISCV Tools V1.10.2 B20201104)|
|optimal : -Os -g -gdwarf-2 -gstrict-dwarf|
|linker : GNU ld (GNU Binutils) 2.32|
|newlibc : 3.0.0|
|author : root|
[DBG]: [__mount_parts:0299]: classname=DMS
[DBG]: [__mount_parts:0300]: devname=dms01
[DBG]: [__mount_parts:0327]: find last lun.
[DBG]: [__mount_parts:0357]: nPart = 1.
[DBG]: [__mount_parts:0486]: dmsPart: "DMS\dms010" is linked to symbel "B".
[ERR]: [esFSYS_pread:0331]: fs fatal err
[ERR]: [esFSYS_pread:0331]: fs fatal err
[ERR]: [esFSYS_pread:0331]: fs fatal err
[ERR]: [esFSYS_pread:0331]: fs fatal err
mount errno: -19!
[DBG]: [esFSYS_mntfs:0333]: melis_devfs,mount on B.
[DBG]: [kservice_maintask:0845]: partition [B] plug in..
[DBG]: [__mount_parts:0299]: classname=DISK
[DBG]: [__mount_parts:0300]: devname=RAMDISK
[DBG]: [__mount_parts:0327]: find last lun.
[DBG]: [__mount_parts:0357]: nPart = 1.
[DBG]: [__mount_parts:0486]: rawpart: "DISK\RAMDISK0" is linked to symbel "C".
[ERR]: [esFSYS_mntfs:0314]: identify the filesystem failure.
[ERR]: [__mount_parts:0541]: mount C failure.
dfs already init.
flash : 1
sip : 0
hal_spi_hw_config()2025 [spi0] clock_frequency = 50000000HZ
hal_spi_init()2215 [spi0] DMA xfer enable
nor_scan
[ERR]: [nor_mxic_quad_mode:0079]: spinor: set mxic QE failed (0x0)
[ERR]: [nor_scan:0537]: spinor: enable quad mode failed
[ERR]: [nor_scan:0544]: spinor: scan nor flash failed
[ERR]: [nor_init:0636]: spinor: init nor flash failed
init nor flash failed
[ERR]: [nor_read:0950]: spinor: read address 0xc000 with len 16384 failed
[ERR]: [register_blk_device:0851]: get gpt from nor flash failed - -5
SDC:hal_sdc_create host:0x402065d8 id:0
host debug mask 3c[ERR] SDC:name ???,port 6,port_num 0,mul_sel 2, pull 1, drv_level 1
[ERR] SDC:name ???,port 6,port_num 1,mul_sel 2, pull 1, drv_level 1
[ERR] SDC:name ???,port 6,port_num 2,mul_sel 2, pull 1, drv_level 1
[ERR] SDC:name ???,port 6,port_num 3,mul_sel 2, pull 1, drv_level 1
[ERR] SDC:name ???,port 6,port_num 4,mul_sel 2, pull 1, drv_level 1
[ERR] SDC:name ???,port 6,port_num 5,mul_sel 2, pull 1, drv_level 1
SDC:Not implement __mci_restore_io,819
SDC:Not imp hal_sdc_init,2236
SDC:hal_sdc_init,2269 no imp
SDC:hal_sdc_init,2278 no imp
SDC:SDC Host Capability:0x3820f Ocr avail:0x3f0000
SDC:Not implement __mci_hold_io,804
SDC:SDC cd_mode:2 present_val:0
SDC:SDC id:0 dma_use:1 present:0
driver version SD/MMC/SDIO Host Controller Driver(v0.29 2022-09-01 16:50) init ok.
host_id =0!
[ERR]: [hal_ths_init:0094]: 0x2009404, 0x2009400, 0x2009430, 0x2009408
key name:thermal_sensor key size:64 key offset:20
thermal_sensor:
02 c1 73 79 0f 30 e9 01
ERR ekernel/drivers/hal/source/usb/manager/usb_manager.c 276 usb_script_parse :script_parser_fetch usbc0 usb_drv_vbus_gpio fail
port_info->port.port_type:2
the cir_master_init success
Warning: clk pll-audio0 should not be changed, please recheck whether the operation is correct
[ehci-usb1] insmod host driver!
phy_vbase : 0x4200800, usbc_no : 1, efuse : 0x1e9300f
scheduler startup
[ohci-usb1] insmod host driver!
phy_vbase : 0x4200800, usbc_no : 1, efuse : 0x1e9300f
[ERR]: [hal_pwm_control:0580]: [pwm7] clk_osc24m not support in sys_config
[ERR]: [hal_pwm_control:0580]: [pwm7] clk_osc24m not support in sys_config
d: partition open failed, please check board storage device!card_detect removed sdmmc_test->card_id=0
[WRN] SD:mmc_card_open card not exit! id:0
card open fail
