芒果派麻雀到手试玩

memory LV 7

麻雀购买链接： https://item.taobao.com/item.htm?id=638644511420
麻雀购买链接： https://item.taobao.com/item.htm?id=638644511420
麻雀购买链接： https://item.taobao.com/item.htm?id=638644511420

D1s Datasheet 1.0

D1s Manual 1.0

PDF原理图： MQ_SCH_v1.5_量产版_带网络.pdf

BOM表（秀！）：
https://mangopi.org/_media/zh/mq_v1.5_bom.html

SDK修改方法与固件下载（非官方玩法）：

简单修改哪吒d1 tina sdk 的 sys_config.fex 和 board.dts，让D1s先把Linux跑起来。
https://bbs.aw-ol.com/topic/384/share/2

memory LV 7

18412d57-0c99-459e-ba40-59aff6e24d81-ed88557096f37abe1719c719c1c73fd.jpg

徒手抓了5只带WIFI的麻雀。

memory LV 7

ce0fd07a-2d0c-4a2b-b7f9-171bea0c64ed-8}V4SH4%$V$3AN%N)MLJ0O9.jpg

烧个一楼的固件到TF卡上电试一试。

memory LV 7

kill已经运行的lvgl_demo，手动运行TF固件自带的 lv_examples 2。

memory LV 7

0215f43b-1372-47fd-a699-98bc7096bed5-cf11d55c98bb6387e741cb0926a88f6.jpg

gonboy LV 5

@memory 在芒果派麻雀到手试玩中说：

l_demo，手动运行TF固件自带的 lv_e

GUI界面用啥开发的？

whycan晕哥 LV 9

@gonboy lvgl7

whycan晕哥 LV 9

此回复已被删除！

memory LV 7

右下角 UART3 PB6/PB7(G / T3 / R3) 可以作为默认的串口输出。

memory LV 7

memory LV 7

因为什么没有优化也没有，所以开机时间挺久。lvgl demo要等gt911触摸驱动就绪，故意延迟了6秒。

memory LV 7

固件与源码下载：芒果派麻雀固件与源码补丁2021-12-14.7z

串口是UART0 PE2 PE3。

readme 里面缺了一步 lunch

pojdd LV 3

请问代码在哪里？

whycan晕哥 LV 9

@pojdd 在芒果派麻雀到手试玩中说：

请问代码在哪里？

① 官方SDK下载： https://d1.docs.aw-ol.com/study/study_2getsdk/

② 骚操作下载：
百度分享: https://pan.baidu.com/s/1QjHPLrWIRQMUb7sr4eBd-g
提取码: 6666
解压密码: whycan.com

md5校验码:

b6a41b47dfccad249ba7b40c5d195717 *d1_sdk.tar.zip.001
1e31cded2fc9f8c602a28fbf63449e8a *d1_sdk.tar.zip.002
9e4cdb935e4ae8b775586bb25505e33a *d1_sdk.tar.zip.003

源码下载后，再打上本帖12楼补丁。

memory LV 7

用热熔胶给小麻雀做套衣裳。

wuzhujian LV 6

@memory
我的屏是480x272的电阻屏，补丁上用的800x480的，是不是合适？
要不，改个480x270的放出来？

memory LV 7

@wuzhujian 在芒果派麻雀到手试玩中说：

@memory
我的屏是480x272的电阻屏，补丁上用的800x480的，是不是合适？
要不，改个480x270的放出来？

嗯，已经准备采购4.3寸屏，开始新建文件夹了：

mkdir target/allwinner/d1-mangopi_mq_rgb480x272_rtp

wuzhujian LV 6

@memory 只建个空目录，应该是没有用的吧？

memory LV 7

@wuzhujian 在芒果派麻雀到手试玩中说：

@memory 只建个空目录，应该是没有用的吧？

5寸800x480，4.3寸480x272补丁：芒果派麻雀固件与源码补丁2021-12-16.7z

LCD颜色貌似还有问题？

TF卡不能读写的问题，请执行：

mount -o remount -o rw /dev/root

memory LV 7

颜色问题找到了，linux设备树 board.dts dmic数字麦克风把显示的信号线占了，disabled就好了。

memory LV 7

WIFI 可以用了。

memory LV 7

固件：芒果派麻雀固件，支持WIFI 2021-12-19.7z

源码补丁： d1-mangopi_mq_source_patch_20211219_by_whycan.tgz

支持麻雀自带的WIFI模块自带的 RTL8189FTV。

解压会覆盖你修改的文件，重要文件请先保存！
解压会覆盖你修改的文件，重要文件请先保存！
解压会覆盖你修改的文件，重要文件请先保存！

启动日志：

[32]HELLO! BOOT0 is starting!
[35]BOOT0 commit : 27369ab
[37]set pll start
[39]periph0 has been enabled
[42]set pll end
[44][pmu]: bus read error
[46]board init ok
[48]ZQ value = 0x2f***********
[51]get_pmu_exist() = -1
[53]ddr_efuse_type: 0xa
[56][AUTO DEBUG] single rank and full DQ!
[60]ddr_efuse_type: 0xa
[63][AUTO DEBUG] rank 0 row = 13
[66][AUTO DEBUG] rank 0 bank = 4
[69][AUTO DEBUG] rank 0 page size = 2 KB
[72]DRAM BOOT DRIVE INFO: V0.24
[75]DRAM CLK = 528 MHz
[78]DRAM Type = 2 (2:DDR2,3:DDR3)
[81]DRAMC read ODT  off.
[83]DRAM ODT off.
[85]ddr_efuse_type: 0xa
[87]DRAM SIZE =64 M
[91]DRAM simple test OK.
[93]dram size =64
[95]card no is 0
[97]sdcard 0 line count 4
[99][mmc]: mmc driver ver 2021-04-2 16:45
[108][mmc]: Wrong media type 0x0
[111][mmc]: ***Try SD card 0***
[120][mmc]: HSSDR52/SDR25 4 bit
[123][mmc]: 50000000 Hz
[125][mmc]: 1904 MB
[127][mmc]: ***SD/MMC 0 init OK!!!***
[174]Loading boot-pkg Succeed(index=0).
[178]Entry_name        = opensbi
[181]Entry_name        = u-boot
[185]Entry_name        = dtb
[187]mmc not para
[189]Jump to second Boot.

OpenSBI v0.6
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|____/_____|
        | |
        |_|

Platform Name          : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs     : 1
Current Hart           : 0
Firmware Base          : 0x40000400
Firmware Size          : 75 KB
Runtime SBI Version    : 0.2

MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0    : 0x0000000040000000-0x000000004001ffff (A)
PMP1    : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2    : 0x0000000000000000-0x0000000007ffffff (A,R,W)
PMP3    : 0x0000000009000000-0x000000000901ffff (▒

U-Boot 2018.05-g0a88ac9 (Apr 30 2021 - 11:23:28 +0000) Allwinner Technology

[00.272]DRAM:  64 MiB
[00.274]Relocation Offset is: 01ef0000
[00.278]secure enable bit: 0
[00.281]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.287]flash init start
[00.289]workmode = 0,storage type = 1
[00.293][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1
[00.298][mmc]: get sdc_type fail and use default host:tm1.
[00.305][mmc]: can't find node "mmc0",will add new node
[00.309][mmc]: fdt err returned <no error>
[00.313][mmc]: Using default timing para
[00.317][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.334][mmc]: card_caps:0x3000000a
[00.337][mmc]: host_caps:0x3000003f
[00.341]sunxi flash init ok
[00.343]line:714 init_clocks
__clk_init: clk pll_periph0x2 already initialized
register fix_factor clk error
[00.353]drv_disp_init
fdt_getprop_u32 s_pwm.pwm-base fail
[00.369]drv_disp_init finish
[00.372]boot_gui_init:start
[00.375]set disp.dev2_output_type fail. using defval=0
[00.381]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[00.404]bmp_name=bootlogo.bmp size 1152054
1152054 bytes read in 50 ms (22 MiB/s)
[00.479]Loading Environment from SUNXI_FLASH... OK
[00.498]out of usb burn from boot: not need burn key
root_partition is rootfs
set root to /dev/mmcblk0p5
[00.509]update part info
[00.512]update bootcmd
[00.515]change working_fdt 0x42aafda8 to 0x42a8fda8
[00.536]update dts
Hit any key to stop autoboot:  0
[00.561]LCD open finish
Android's image name: d1-mangopi_mq_rg
No reserved memory region found in source FDT
[00.978]
Starting kernel ...

[00.981][mmc]: MMC Device 2 not found
[00.984][mmc]: mmc 2 not find, so not exit
[    0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000
[    0.000000] Linux version 5.4.61 (whycan@ubuntu) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #1 PREEMPT Mon Dec 20 13:27:25 UTC 2021
[    0.000000] cma: Reserved 8 MiB at 0x0000000043800000
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000040200000-0x0000000043ffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040200000-0x0000000043ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x0000000043ffffff]
[    0.000000] On node 0 totalpages: 15872
[    0.000000]   DMA32 zone: 217 pages used for memmap
[    0.000000]   DMA32 zone: 0 pages reserved
[    0.000000]   DMA32 zone: 15872 pages, LIFO batch:3
[    0.000000] elf_hwcap is 0x20112d
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 15655
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:recovery@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g0a88ac9(04/30/2021-11:23:28) mbr_offset=15
[    0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.000000] Sorting __ex_table...
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 42192K/63488K available (6104K kernel code, 650K rwdata, 2103K rodata, 196K init, 252K bss, 13104K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[    0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000026] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[    0.000378] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.001014] Console: colour dummy device 80x25
[    0.001063] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.001082] pid_max: default: 32768 minimum: 301
[    0.001282] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.001303] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.003390] ASID allocator initialised with 65536 entries
[    0.003588] rcu: Hierarchical SRCU implementation.
[    0.004319] devtmpfs: initialized
[    0.017181] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0
[    0.018347] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.018382] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[    0.018937] pinctrl core: initialized pinctrl subsystem
[    0.020642] NET: Registered protocol family 16
[    0.022846] DMA: preallocated 256 KiB pool for atomic allocations
[    0.023586] cpuidle: using governor menu
[    0.065894] rtc_ccu: sunxi ccu init OK
[    0.074243] clock: sunxi ccu init OK
[    0.075324] clock: sunxi ccu init OK
[    0.114806] iommu: Default domain type: Translated
[    0.115016] sunxi iommu: irq = 4
[    0.116297] SCSI subsystem initialized
[    0.116705] usbcore: registered new interface driver usbfs
[    0.116801] usbcore: registered new interface driver hub
[    0.116919] usbcore: registered new device driver usb
[    0.117139] mc: Linux media interface: v0.10
[    0.117224] videodev: Linux video capture interface: v2.00
[    0.118510] sunxi-msgbox-amp 3003000.msgbox: invalid resource
[    0.119334] Advanced Linux Sound Architecture Driver Initialized.
[    0.119993] Bluetooth: Core ver 2.22
[    0.120088] NET: Registered protocol family 31
[    0.120100] Bluetooth: HCI device and connection manager initialized
[    0.120125] Bluetooth: HCI socket layer initialized
[    0.120145] Bluetooth: L2CAP socket layer initialized
[    0.120193] Bluetooth: SCO socket layer initialized
[    0.120653] pwm module init!
[    0.123445] clocksource: Switched to clocksource riscv_clocksource
[    0.137721] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.156440] thermal_sys: Registered thermal governor 'step_wise'
[    0.156446] thermal_sys: Registered thermal governor 'user_space'
[    0.157051] NET: Registered protocol family 2
[    0.157940] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.157990] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.158011] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.158027] TCP: Hash tables configured (established 512 bind 512)
[    0.158208] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.158256] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.158551] NET: Registered protocol family 1
[    0.161498] Initialise system trusted keyrings
[    0.161827] workingset: timestamp_bits=62 max_order=14 bucket_order=0
[    0.170458] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.192097] Key type asymmetric registered
[    0.192116] Asymmetric key parser 'x509' registered
[    0.192142] io scheduler mq-deadline registered
[    0.192152] io scheduler kyber registered
[    0.192177] atomic64_test: passed
[    0.193640] [DISP]disp_module_init
[    0.194366] disp 5000000.disp: Adding to iommu group 0
[    0.195119] [DISP] disp_init,line:2385:
[    0.195126] smooth display screen:0 type:1 mode:4
[    0.224344] disp 5000000.disp: 5000000.disp supply vcc-lcd not found, using dummy regulator
[    0.224661] disp 5000000.disp: 5000000.disp supply vcc-pd not found, using dummy regulator
[    0.237387] [DISP] disp_sys_pwm_request,line:442:
[    0.237394] disp_sys_pwm_request pwm 8 fail! -517
[    0.237410] [DISP] disp_sys_pwm_config,line:509:
[    0.237413] disp_sys_pwm_Config, handle is NULL!
[    0.238086] display_fb_request,fb_id:0
[    0.257975] disp_al_manager_apply ouput_type:1
[    0.258121] [DISP] lcd_clk_config,line:731:
[    0.258135] disp 0, clk: pll(198000000),clk(198000000),dclk(33000000) dsi_rate(198000000)
[    0.258135]      clk real:pll(288000000),clk(288000000),dclk(48000000) dsi_rate(0)
[    0.258198] [DISP] disp_sys_gpio_request,line:276:
[    0.258206] disp_sys_gpio_request failed, gpio_name=lcd_bl_en, gpio=123, value=0, ret=-517
[    0.258222] [DISP] disp_sys_pwm_request,line:442:
[    0.258226] disp_sys_pwm_request pwm 8 fail! -517
[    0.258858] [DISP]disp_module_init finish
[    0.259824] sunxi_sid_init()506 - insmod ok
[    0.268249] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    0.268941] uart uart0: get regulator failed
[    0.268973] uart uart0: uart0 supply uart not found, using dummy regulator
[    0.269399] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI
[    0.269431] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
[    1.062486] printk: console [ttyS0] enabled
[    1.068160] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    1.079722] uart uart1: get regulator failed
[    1.084618] uart uart1: uart1 supply uart not found, using dummy regulator
[    1.092728] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI
[    1.102441] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    1.113978] uart uart3: get regulator failed
[    1.118801] uart uart3: uart3 supply uart not found, using dummy regulator
[    1.126918] uart3: ttyS3 at MMIO 0x2500c00 (irq = 21, base_baud = 1500000) is a SUNXI
[    1.137014] misc dump reg init
[    1.141442] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    1.148708] sunxi-rfkill soc@3000000:rfkill@0: devm_pinctrl_get() failed!
[    1.156391] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    1.163728] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    1.171144] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    1.177728] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    1.184705] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[    1.192582] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[    1.200787] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[    1.208481] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[    1.215345] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0
[    1.223599] [ADDR_MGT] addr_mgt_probe: module version: v1.0.9
[    1.231220] [ADDR_MGT] addr_mgt_probe: success.
[    1.237914] libphy: Fixed MDIO Bus: probed
[    1.242489] CAN device driver interface
[    1.247233] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.254570] sunxi-ehci: EHCI SUNXI driver
[    1.259659] get ehci0-controller wakeup-source is fail.
[    1.265667] sunxi ehci0-controller don't init wakeup source
[    1.271924] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe000904290, 0x:ffffffd004078000, irq_no:2e
[    1.285485] [sunxi-ehci0]: Not init ehci0
[    1.290399] get ehci1-controller wakeup-source is fail.
[    1.296470] sunxi ehci1-controller don't init wakeup source
[    1.302752] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe000904650, 0x:ffffffd00407c000, irq_no:31
[    1.316345] hci: sunxi_insmod_ehci()600 WARN: get supply failed
[    1.322993] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    1.330329] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    1.340274] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[    1.373497] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    1.382448] hub 1-0:1.0: USB hub found
[    1.386831] hub 1-0:1.0: 1 port detected
[    1.392166] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.399238] sunxi-ohci: OHCI SUNXI driver
[    1.404362] get ohci0-controller wakeup-source is fail.
[    1.410362] sunxi ohci0-controller don't init wakeup source
[    1.416641] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe000904dd0
[    1.427104] [sunxi-ohci0]: Not init ohci0
[    1.432016] get ohci1-controller wakeup-source is fail.
[    1.438036] sunxi ohci1-controller don't init wakeup source
[    1.444359] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe000905190
[    1.454844] hci: sunxi_insmod_ohci()265 WARN: get supply failed
[    1.461494] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    1.468812] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    1.478705] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[    1.558606] hub 2-0:1.0: USB hub found
[    1.562871] hub 2-0:1.0: 1 port detected
[    1.568653] usbcore: registered new interface driver uas
[    1.574865] usbcore: registered new interface driver usb-storage
[    1.581690] usbcore: registered new interface driver ums-alauda
[    1.588471] usbcore: registered new interface driver ums-cypress
[    1.595384] usbcore: registered new interface driver ums-datafab
[    1.602170] usbcore: registered new interface driver ums_eneub6250
[    1.609259] usbcore: registered new interface driver ums-freecom
[    1.616151] usbcore: registered new interface driver ums-isd200
[    1.622822] usbcore: registered new interface driver ums-jumpshot
[    1.629807] usbcore: registered new interface driver ums-karma
[    1.636444] usbcore: registered new interface driver ums-onetouch
[    1.643379] usbcore: registered new interface driver ums-realtek
[    1.650288] usbcore: registered new interface driver ums-sddr09
[    1.657033] usbcore: registered new interface driver ums-sddr55
[    1.663835] usbcore: registered new interface driver ums-usbat
[    1.670872] mousedev: PS/2 mouse device common for all mice
[    1.678020] ts probe start
[    1.678436] input: 2009c00.rtp as /devices/platform/soc@3000000/2009c00.rtp/input/input0
[    1.691139] ts probe success
[    1.691562] sunxi_gpadc_init,1968, success
[    1.700300] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[    1.712720] sunxi-rtc 7090000.rtc: registered as rtc0
[    1.718592] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:02 UTC (2)
[    1.727503] sunxi-rtc 7090000.rtc: sunxi rtc probed
[    1.733384] i2c /dev entries driver
[    1.737474] IR NEC protocol handler initialized
[    1.742564] IR RC5(x/sz) protocol handler initialized
[    1.748244] IR RC6 protocol handler initialized
[    1.753316] IR JVC protocol handler initialized
[    1.758397] IR Sony protocol handler initialized
[    1.763569] IR SANYO protocol handler initialized
[    1.768835] IR Sharp protocol handler initialized
[    1.774111] IR MCE Keyboard/mouse protocol handler initialized
[    1.780634] IR XMP protocol handler initialized
[    1.785717] ir_imon_decoder: IR iMON protocol handler initialized
[    1.792529] IR RCMM protocol handler initialized
[    1.798445] sunxi cedar version 1.1
[    1.802684] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    1.808995] VE: install start!!!
[    1.808995]
[    1.814643] VE: cedar-ve the get irq is 6
[    1.814643]
[    1.821010] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____)
[    1.821010]
[    1.832665] VE: install end!!!
[    1.832665]
[    1.839328] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.848580] Bluetooth: HCI UART driver ver 2.3
[    1.853595] Bluetooth: HCI UART protocol H4 registered
[    1.859360] Bluetooth: HCI UART protocol BCSP registered
[    1.865321] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    1.872677] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1
[    1.879127] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1
[    1.885771] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled!
[    1.885771]
[    1.894499] [XR_BT_LPM] bluesleep_probe: uart_index(1)
[    1.903644] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50)
[    1.913673] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    1.919885] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    1.926280] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    1.932691] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    1.939171] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    1.945709] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    1.952239] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    1.958780] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    1.965862] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[    1.971352] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[    1.978122] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.989335] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    2.009542] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.034038] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[    2.039714] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.052080] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50)
[    2.062171] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    2.068571] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    2.074970] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    2.081456] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    2.087951] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.099578] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    2.106124] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    2.112655] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    2.119306] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    2.125959] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    2.135506] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.147764] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.159017] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    2.167969] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.179620] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.204028] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    2.211710] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.219396] usbcore: registered new interface driver usbhid
[    2.225658] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[    2.232619] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.244265] usbhid: USB HID core driver
[    2.250510] usbcore: registered new interface driver snd-usb-audio
[    2.260729] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.272386] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.282535] [AUDIOCODEC][sunxi_codec_parse_params][2094]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    2.282535]
[    2.299928] [AUDIOCODEC][sunxi_codec_parse_params][2130]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    2.310925] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    2.323063] [AUDIOCODEC][sunxi_internal_codec_probe][2266]:codec probe finished
[    2.331244] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.338216] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    2.349875] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.357537] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.364598] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    2.376258] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[    2.383066] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    2.394947] sid_rd_ver_reg()254 - ver >= 4, soc ver:5
[    2.400667] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    2.410595] mmc0: new high speed SD card at address 0002
[    2.416749] [SNDCODEC][sunxi_card_init][583]:card init finished
[    2.425002] mmcblk0: mmc0:0002 N/A   1.86 GiB
[    2.434018] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    2.445728]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[    2.451366] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1
[    2.466779] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished
[    2.475189] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102!
[    2.486911] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed
[    2.499263] NET: Registered protocol family 10
[    2.505890] Segment Routing with IPv6
[    2.510206] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    2.517871] NET: Registered protocol family 17
[    2.522914] can: controller area network core (rev 20170425 abi 9)
[    2.530091] NET: Registered protocol family 29
[    2.535135] can: raw protocol (rev 20170425)
[    2.539933] can: broadcast manager protocol (rev 20170425 t)
[    2.546307] can: netlink gateway (rev 20190810) max_hops=1
[    2.552825] Bluetooth: RFCOMM TTY layer initialized
[    2.558436] Bluetooth: RFCOMM socket layer initialized
[    2.564316] Bluetooth: RFCOMM ver 1.11
[    2.569779] Loading compiled-in X.509 certificates
[    2.578211] HDMI 2.0 driver init start!
[    2.582506] boot_hdmi=false
[    2.585831] ERROR: pinctrl_get for HDMI2.0 DDC fail
[    2.592936] HDMI2.0 module init end
[    2.628902] twi twi2: twi2 supply twi not found, using dummy regulator
[    2.642497] sunxi_i2c_probe()2262 - [i2c2] probe success
[    2.655010] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.666873] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.674608] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.684359] clk: Not disabling unused clocks
[    2.689158] ALSA device list:
[    2.692468]   #0: audiocodec
[    2.695841] cfg80211: failed to load regulatory.db
[    2.701326] alloc_fd: slot 0 not NULL!
[    2.718764] EXT4-fs (mmcblk0p5): mounted filesystem without journal. Opts: (null)
[    2.727358] VFS: Mounted root (ext4 filesystem) readonly on device 179:5.
[    2.736028] devtmpfs: mounted
[    2.739593] Freeing unused kernel memory: 196K
[    2.744642] This architecture does not have kernel memory protection.
[    2.751862] Run /sbin/init as init process
[    2.758555] random: fast init done
[    2.895282] init: Console is alive
[    2.899425] init: - watchdog -
[    2.903018] init: - preinit -
[    3.173587] [SNDCODEC][sunxi_check_hs_detect_status][191]:plugin --> switch:1
formating /dev/by-name/UDISK to ext4
/etc/preinit: line 1: mkfs.ext4: not found
[    3.282389] mount_root: mounting /dev/root
[    3.287573] EXT4-fs (mmcblk0p5): re-mounted. Opts: (null)
[    3.294082] mount_root: loading kmods from internal overlay
[    3.408721] block: attempting to load /etc/config/fstab
[    3.417361] block: extroot: device not present, retrying in 5 seconds
[    3.685040] random: procd: uninitialized urandom read (4 bytes read)
[    6.183481] hdmi_hpd_sys_config_release
[    6.203483]
[    6.203483] insmod_device_driver
[    6.203483]
[    8.494277] block: extroot: cannot find device UDISK
[    8.514803] procd: - early -
[    8.518277] procd: - watchdog -
[    8.533012] random: procd: uninitialized urandom read (4 bytes read)
[    8.869571] procd: - watchdog -
[    8.883899] procd: - ubus -
[    8.887860] procd (1): /proc/114/oom_adj is deprecated, please use /proc/114/oom_score_adj instead.
[    8.912755] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.943124] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.991109] procd: - init -
Please press Enter to activate this console.
[   10.117253] fuse: init (API version 7.31)
[   10.464647] file system registered
[   10.604944] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[   10.937802] read descriptors
[   10.941032] read strings
[   11.143694] sunxi_set_cur_vol_work()394 WARN: get power supply failed
[   11.234242] android_work: sent uevent USB_STATE=CONNECTED
[   11.240328] sunxi_set_cur_vol_work()394 WARN: get power supply failed
[   11.365671] configfs-gadget gadget: high-speed config #1: c
[   11.372084] android_work: sent uevent USB_STATE=CONFIGURED
[   16.397455] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   33.639037] RTL871X: module init start
[   33.643226] RTL871X: rtl8189fs v4.3.24.8_22657.20170607
[   33.649475] RTL871X: module init ret=0
[   47.068520] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[   47.084895] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[   47.192068] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   47.206986] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   47.229279] get ctp_power is fail, -22
[   47.233610] get ctp_power_ldo_vol is fail, -22
[   47.238614] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   47.250303] sunxi_ctp_startup: ctp_power_io is invalid.
[   47.256671] get ctp_gesture_wakeup fail, no gesture wakeup
[   47.262884] gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator
[   47.284752] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   47.299489] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   47.312844] sunxi-mmc 4021000.sdmmc: card claims to support voltages below defined range
[   47.331905] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   47.343589] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   47.355570] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[   47.368975] mmc1: new high speed SDIO card at address 0001
[   47.376198] RTL871X: CHIP TYPE: RTL8188F
[   47.381049] RTL871X: rtw_hal_config_rftype RF_Type is 3 TotalTxPath is 1
[   47.388705] RTL871X: Chip Version Info: CHIP_8188F_Normal_Chip_SMIC_B_CUT_1T1R_RomVer(0)
[   47.398036] RTL871X: SetHwReg8188F: hci_sus_state=1
[   47.405603] RTL871X: SetHwReg8188F: bMacPwrCtrlOn=1
[   47.411042] RTL871X: SetHwReg8188F: hci_sus_state=2
[   47.416905] RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f
[   47.424371] RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same.
[   47.433271] RTL871X: PowerOnCheck: 0x1B8 test Pass.
[   47.438919] RTL871X: EEPROM type is E-FUSE
[   47.444304] RTL871X: hal_EfuseSwitchToBank: Efuse switch bank to 0
[   47.483871] input: gt9xxnew_ts as /devices/virtual/input/input2
[   47.583818] xt_time: kernel timezone is -0000
[   47.614031] RTL871X: hal_ReadEFuse_WiFi: data end at address=0x98
[   47.633574] RTL871X: HW EFUSE
[   47.636889] RTL871X: 0x000:
[   47.636893] 29
[   47.640097] 81
[   47.642041] 03
[   47.673656] CC
[   47.675611] 00
[   47.677556] 00
[   47.679536] 50
[   47.681481] 00
[   47.683424] 00
[   47.700132] 00
[   47.707829] 04
[   47.711022] CC
[   47.717240] 0A
[   47.719194] 0C
[   47.721139] 00
[   47.723083] 00
[   47.738623] RTL871X: 0x010:
[   47.738630] 2A
[   47.741844] 2A
[   47.745287] 2A
[   47.753624] 2A
[   47.755579] 2A
[   47.757523] 2A
[   47.759502] 2D
[   47.761449] 2D
[   47.763393] 2D
[   47.773560] 2D
[   47.775516] 2D
[   47.777459] 03
[   47.779403] FF
[   47.781345] FF
[   47.783323] FF
[   47.790853] FF
[   47.795499] RTL871X: 0x020:
[   47.795505] FF
[   47.803558] FF
[   47.805549] FF
[   47.807496] FF
[   47.809440] FF
[   47.811384] FF
[   47.813328] FF
[   47.828348] FF
[   47.830303] FF
[   47.832538] FF
[   47.842267] FF
[   47.844370] FF
[   47.846319] FF
[   47.848261] FF
[   47.850205] FF
[   47.852188] FF
[   47.866169] RTL871X: 0x030:
[   47.866177] FF
[   47.869390] FF
[   47.871335] FF
[   47.873279] FF
[   47.885729] FF
[   47.887684] FF
[   47.889628] FF
[   47.891573] FF
[   47.895778] FF
[   47.903630] FF
[   47.905584] FF
[   47.907528] FF
[   47.909510] FF
[   47.911454] FF
[   47.913398] FF
[   47.925619] FF
[   47.929418] RTL871X: 0x040:
[   47.929420] FF
[   47.932659] FF
[   47.938135] FF
[   47.942488] FF
[   47.952864] FF
[   47.955003] FF
[   47.956954] FF
[   47.958897] FF
[   47.960832] FF
[   47.963066] FF
[   47.973574] FF
[   47.975529] FF
[   47.977473] FF
[   47.979454] FF
[   47.981400] FF
[   47.983345] FF
[   47.993595] RTL871X: 0x050:
[   47.993602] FF
[   47.996816] FF
[   47.998759] FF
[   48.000703] FF
[   48.002682] FF
[   48.010863] FF
[   48.015146] FF
[   48.017100] FF
[   48.019045] FF
[   48.021279] FF
[   48.023224] FF
[   48.036011] FF
[   48.037964] FF
[   48.039908] FF
[   48.041852] FF
[   48.051147] FF
[   48.056627] RTL871X: 0x060:
[   48.056635] FF
[   48.062553] FF
[   48.067059] FF
[   48.069014] FF
[   48.070992] FF
[   48.072939] FF
[   48.085651] FF
[   48.093566] FF
[   48.095520] FF
[   48.097755] FF
[   48.099690] FF
[   48.101634] FF
[   48.142822] FF
[   48.153581] FF
[   48.155537] FF
[   48.157480] FF
[   48.161269] RTL871X: 0x070:
[   48.161271] FF
[   48.186590] FF
[   48.188545] FF
[   48.203586] FF
[   48.205541] FF
[   48.207484] FF
[   48.209463] FF
[   48.211409] FF
[   48.213351] FF
[   48.253625] FF
[   48.255615] FF
[   48.257561] FF
[   48.259505] FF
[   48.261447] FF
[   48.263391] FF
[   48.282048] FF
[   48.290261] RTL871X: 0x080:
[   48.290268] FF
[   48.293680] FF
[   48.297105] FF
[   48.299059] FF
[   48.310530] FF
[   48.312484] FF
[   48.325832] FF
[   48.327788] FF
[   48.329732] FF
[   48.331968] FF
[   48.353552] FF
[   48.355507] FF
[   48.357451] FF
[   48.359429] FF
[   48.361376] FF
[   48.363320] FF
[   48.387743] RTL871X: 0x090:
[   48.387749] FF
[   48.390962] FF
[   48.392906] FF
[   48.410983] FF
[   48.413044] FF
[   48.423594] FF
[   48.425548] FF
[   48.427493] FF
[   48.429474] FF
[   48.431711] FF
[   48.453549] FF
[   48.455504] FF
[   48.457448] FF
[   48.459392] FF
[   48.461335] FF
[   48.463315] FF
[   48.477368] RTL871X: 0x0a0:
[   48.477374] FF
[   48.485013] FF
[   48.489303] FF
[   48.491257] FF
[   48.494856] FF
[   48.503914] FF
[   48.505868] FF
[   48.507813] FF
[   48.511279] FF
[   48.520802] FF
[   48.522756] FF
[   48.524811] FF
[   48.528391] FF
[   48.530345] FF
[   48.537763] FF
[   48.539718] FF
[   48.548406] RTL871X: 0x0b0:
[   48.548413] FF
[   48.556888] FF
[   48.558841] FF
[   48.560786] FF
[   48.568178] FF
[   48.570134] FF
[   48.572078] FF
[   48.580070] FF
[   48.582024] 20
[   48.591002] 25
[   48.592957] 1A
[   48.598435] 00
[   48.600389] 00
[   48.608610] 00
[   48.610565] 00
[   48.612576] FF
[   48.619565] RTL871X: 0x0c0:
[   48.619572] FF
[   48.628059] 11
[   48.630014] 00
[   48.631957] 10
[   48.640370] 00
[   48.642324] FF
[   48.650623] 00
[   48.652578] FF
[   48.656608] 00
[   48.658918] 00
[   48.666328] FF
[   48.668283] FF
[   48.670293] FF
[   48.678528] FF
[   48.680484] FF
[   48.682464] FF
[   48.691585] RTL871X: 0x0d0:
[   48.691591] 3E
[   48.699371] 10
[   48.701327] 01
[   48.708509] 12
[   48.713254] 23
[   48.724714] FF
[   48.733698] FF
[   48.735653] FF
[   48.743584] 20
[   48.745829] 04
[   48.747772] 4C
[   48.763577] 02
[   48.770757] 79
[   48.772712] F1
[   48.783354] 21
[   48.793559] 02
[   48.801176] RTL871X: 0x0e0:
[   48.801183] 0C
[   48.813561] 00
[   48.815594] 22
[   48.817544] 04
[   48.819488] 00
[   48.832986] 08
[   48.846306] 00
[   48.853629] 32
[   48.855620] FF
[   48.857857] 21
[   48.875374] 02
[   48.877415] 0C
[   48.879396] 00
[   48.893605] 22
[   48.895559] 2A
[   48.908219] 01
[   48.912019] RTL871X: 0x0f0:
[   48.912021] 01
[   48.920525] 00
[   48.922478] 00
[   48.926676] 00
[   48.930691] 00
[   48.938284] 00
[   48.940238] 00
[   48.944812] 00
[   48.947147] 00
[   48.950502] 00
[   48.952457] 00
[   48.959856] 00
[   48.961811] 02
[   48.965227] 00
[   48.967180] FF
[   48.969125] FF
[   48.983568] RTL871X: 0x100:
[   48.983647] 00
[   48.986860] 00
[   48.990668] 00
[   48.992621] 00
[   49.000101] 00
[   49.002056] 00
[   49.007071] 00
[   49.012655] 00
[   49.017787] 00
[   49.020031] 00
[   49.021976] 00
[   49.028951] 00
[   49.032845] 00
[   49.036318] 00
[   49.038271] 00
[   49.040251] 00
[   49.059572] RTL871X: 0x110:
[   49.059579] 00
[   49.062856] EB
[   49.070250] 00
[   49.072203] 6E
[   49.075091] 01
[   49.077135] 00
[   49.079082] 00
[   49.081027] 00
[   49.091275] 00
[   49.094358] FF
[   49.096312] 94
[   49.098295] A4
[   49.108895] 08
[   49.113066] C5
[   49.116079] 12
[   49.118032] 65
[   49.127057] RTL871X: 0x120:
[   49.127063] FF
[   49.130278] FF
[   49.140277] FF
[   49.148877] FF
[   49.150831] FF
[   49.152776] FF
[   49.163628] FF
[   49.171513] FF
[   49.178136] FF
[   49.191577] FF
[   49.202072] FF
[   49.207205] FF
[   49.209157] FF
[   49.211102] FF
[   49.233551] FF
[   49.242718] FF
[   49.253564] RTL871X: 0x130:
[   49.253571] FF
[   49.256784] FF
[   49.279696] FF
[   49.281651] FF
[   49.290480] FF
[   49.292435] FF
[   49.306887] FF
[   49.311541] FF
[   49.316947] FF
[   49.325773] FF
[   49.331684] FF
[   49.338982] FF
[   49.341324] FF
[   49.349836] FF
[   49.358768] FF
[   49.361934] FF
[   49.368639] RTL871X: 0x140:
[   49.368646] FF
[   49.372269] FF
[   49.379529] FF
[   49.386072] FF
[   49.391057] FF
[   49.403685] FF
[   49.416061] FF
[   49.418016] FF
[   49.419961] FF
[   49.443026] FF
[   49.453548] FF
[   49.455541] FF
[   49.457487] FF
[   49.476209] FF
[   49.483562] FF
[   49.493604] FF
[   49.512948] RTL871X: 0x150:
[   49.512954] FF
[   49.523617] FF
[   49.525608] FF
[   49.527553] FF
[   49.555457] FF
[   49.557411] FF
[   49.559401] FF
[   49.582190] FF
[   49.585570] FF
[   49.593555] FF
[   49.595508] FF
[   49.597452] FF
[   49.625773] FF
[   49.633574] FF
[   49.635528] FF
[   49.653142] FF
[   49.661134] RTL871X: 0x160:
[   49.661141] FF
[   49.670404] FF
[   49.673558] FF
[   49.696461] FF
[   49.698453] FF
[   49.700398] FF
[   49.733442] FF
[   49.735503] FF
[   49.737448] FF
[   49.762875] FF
[   49.774502] FF
[   49.783564] FF
[   49.785518] FF
[   49.799400] FF
[   49.801419] FF
[   49.819175] FF
[   49.822973] RTL871X: 0x170:
[   49.822975] FF
[   49.841961] FF
[   49.847063] FF
[   49.849055] FF
[   49.851002] FF
[   49.866140] FF
[   49.868095] FF
[   49.875437] FF
[   49.877393] FF
[   49.879628] FF
[   49.902180] FF
[   49.909170] FF
[   49.911126] FF
[   49.933565] FF
[   49.941251] FF
[   49.943207] FF
[   49.962567] RTL871X: 0x180:
[   49.962573] FF
[   49.977028] FF
[   49.990488] FF
[   49.992443] FF
[   50.007252] FF
[   50.009271] FF
[   50.023567] FF
[   50.025521] FF
[   50.043888] FF
[   50.048804] FF
[   50.050758] FF
[   50.052703] FF
[   50.083654] FF
[   50.085609] FF
[   50.103214] FF
[   50.108340] FF
[   50.112140] RTL871X: 0x190:
[   50.112142] FF
[   50.141273] FF
[   50.150859] FF
[   50.152814] FF
[   50.163640] FF
[   50.173587] FF
[   50.175541] FF
[   50.182710] FF
[   50.187845] FF
[   50.190091] FF
[   50.192035] FF
[   50.209686] FF
[   50.211641] FF
[   50.223641] FF
[   50.230885] FF
[   50.232839] FF
[   50.262179] RTL871X: 0x1a0:
[   50.262187] FF
[   50.276677] FF
[   50.286602] FF
[   50.288557] FF
[   50.290502] FF
[   50.339184] FF
[   50.341139] FF
[   50.343084] FF
[   50.378588] FF
[   50.380834] FF
[   50.413554] FF
[   50.425874] FF
[   50.427828] FF
[   50.429772] FF
[   50.466046] FF
[   50.483984] FF
[   50.508738] RTL871X: 0x1b0:
[   50.508744] FF
[   50.511958] FF
[   50.534849] FF
[   50.536804] FF
[   50.538749] FF
[   50.576967] FF
[   50.578922] FF
[   50.580867] FF
[   50.609079] FF
[   50.611324] FF
[   50.613269] FF
[   50.661562] FF
[   50.673101] FF
[   50.694773] FF
[   50.715551] FF
[   50.756191] [SNDCODEC][sunxi_card_hw_params][620]:stream_flag: 0
[   50.765723] FF
[   50.767580] RTL871X: 0x1c0:
[   50.767583] FF
Trying to connect to SWUpdate...[   50.806408] FF

[   50.829238] FF
[   50.832591] FF
[   50.882080] FF
[   50.919546] FF
[   50.933542] FF
[   50.935496] FF
[   50.974786] FF
[   50.977031] FF
[   51.002264] FF
[   51.020739] FF
[   51.022693] FF
[   51.071160] FF
[   51.073367] FF
[   51.111137] FF
[   51.136503] RTL871X: 0x1d0:
[   51.136510] FF
[   51.139789] FF
[   51.187972] FF
[   51.189926] FF
[   51.205992] FF
[   51.218640] FF
[   51.220662] FF
[   51.222609] FF
[   51.241975] FF
[   51.260207] FF
[   51.263104] FF
[   51.273712] FF
[   51.275667] FF
[   51.277612] FF
[   51.293561] FF
[   51.295516] FF
[   51.314351] RTL871X: 0x1e0:
[   51.314357] FF
[   51.337135] FF
[   51.346667] FF
[   51.349666] FF
[   51.351621] FF
[   51.367045] FF
[   51.369000] FF
[   51.377600] FF
[   51.379556] FF
[   51.395979] FF
[   51.402447] FF
[   51.412654] FF
[   51.414845] FF
[   51.416863] FF
[   51.418809] FF
[   51.428014] FF
[   51.437267] RTL871X: 0x1f0:
[   51.437273] FF
[   51.440524] FF
[   51.450047] FF
[   51.452039] FF
[   51.466478] FF
[   51.468433] FF
[   51.470376] FF
[   51.472938] FF
[   51.477399] FF
[   51.487090] FF
[   51.489045] FF
[   51.490989] FF
[   51.497352] FF
[   51.500525] FF
[   51.502479] FF
[   51.513556] FF
[   51.517353]
[   51.528569] RTL871X: hal_com_config_channel_plan chplan:0x20
[   51.574453] RTL871X: kfree flag:1
[   51.590110] RTL871X: bb_gain:-1
[   51.609258] RTL871X: rtl8188f_FirmwareDownload((null)) tmp_ps=3
[   51.631597] RTL871X: rtl8188f_FirmwareDownload fw: FW_NIC, size: 21020
[   51.658102] RTL871X: rtl8188f_FirmwareDownload: fw_ver=4 fw_subver=0000 sig=0x88f1, Month=08, Date=22, Hour=17, Minute=36
[   51.698071] RTL871X: rtl8188f_FirmwareDownload(): Shift for fw header!
[   51.733643] RTL871X: rtl8188f_FirmwareDownload by IO write!
[   52.099997] random: crng init done
[   52.103799] random: 6 urandom warning(s) missed due to ratelimiting
[   52.233170] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x07050105
[   52.247012] RTL871X: _8051Reset8188: Finish
[   52.260583] RTL871X: _FWFreeToGo: Polling FW ready OK! (88, 20ms), REG_MCUFWDL:0x070501c6
[   52.273673] RTL871X: rtl8188f_FirmwareDownload: DLFW OK !
[   52.279777] RTL871X: rtl8188f_FirmwareDownload success. write_fw:1, 540ms
[   52.290759] RTL871X:  <=== rtl8188f_FirmwareDownload()
[   52.297212] RTL871X: hal_read_mac_hidden_rpt OK! (1, 0ms), fwdl:1, id:0x19
[   52.309457] RTL871X: SetHwReg8188F: bMacPwrCtrlOn=0
[   52.315039] RTL871X: SetHwReg8188F: hci_sus_state=3
[   52.321666] RTL871X: SetHwReg8188F: hci_sus_state=0
[   52.329862] RTL871X: rtw_hal_read_chip_info in 4930 ms
[   52.336099] RTL871X: init_channel_set((null)) ChannelPlan ID:0x20, ch num:13
[   52.353335] RTL871X: rtw_alloc_macid((null)) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1
[   52.372386] RTL871X: Init_ODM_ComInfo_8188f(): fab_ver=0 cut_ver=1
[   52.406031] RTL871X: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[   52.457875] RTL871X: phy_ConfigBBWithPgParaFile(): No File PHY_REG_PG.txt, Load from HWImg Array!
[   52.480548] RTL871X: default power by rate loaded
[   52.492385] RTL871X: rtw_macaddr_cfg mac addr:94:a4:08:c5:12:65
[   52.512064] RTL871X: bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0
[   52.535398] RTL871X: rtw_wiphy_alloc(phy0)
[   52.551979] RTL871X: rtw_wdev_alloc(padapter=00000000d5fe995c)
[   52.568929] RTL871X: rtw_wiphy_register(phy0)
[   52.577931] RTL871X: Register RTW cfg80211 vendor cmd(0x67) interface
[   52.593682] RTL871X: _rtw_reg_notifier
[   52.597953] RTL871X: _rtw_reg_notifier_apply: NL80211_REGDOM_SET_BY_CORE to DRV
[   52.610417] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=94:a4:08:c5:12:65
[   52.622198] RTL871X: cfg80211_rtw_get_txpower
[   63.293066] RTL871X: cfg80211_rtw_get_txpower
[   63.298627] RTL871X: cfg80211_rtw_get_txpower
[   63.304426] RTL871X: cfg80211_rtw_get_txpower
[   63.309675] RTL871X: cfg80211_rtw_get_txpower
[   63.317605] RTL871X: cfg80211_rtw_get_txpower
[   63.322844] RTL871X: +871x_drv - drv_open, bup=0
[   63.328610] RTL871X: FW does not exist before power on!!
[   63.335639] RTL871X: SetHwReg8188F: hci_sus_state=1
[   63.343267] RTL871X: SetHwReg8188F: bMacPwrCtrlOn=1
[   63.351824] RTL871X: SetHwReg8188F: hci_sus_state=2
[   63.363956] RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f
[   63.381736] RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same.
[   63.394795] RTL871X: PowerOnCheck: 0x1B8 test Pass.
[   63.403639] RTL871X: Power on ok!
[   63.412914] RTL871X: rtl8188f_FirmwareDownload(wlan0) tmp_ps=3
[   63.424699] RTL871X: rtl8188f_FirmwareDownload fw: FW_NIC, size: 21020
[   63.441927] RTL871X: rtl8188f_FirmwareDownload: fw_ver=4 fw_subver=0000 sig=0x88f1, Month=08, Date=22, Hour=17, Minute=36
[   63.457354] RTL871X: rtl8188f_FirmwareDownload(): Shift for fw header!
[   63.473630] RTL871X: rtl8188f_FirmwareDownload by IO write!
[   63.733256] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050105
[   63.744024] RTL871X: _8051Reset8188: Finish
[   63.757606] RTL871X: _FWFreeToGo: Polling FW ready OK! (85, 10ms), REG_MCUFWDL:0x000501c6
[   63.767097] RTL871X: rtl8188f_FirmwareDownload: DLFW OK !
[   63.773392] RTL871X: rtl8188f_FirmwareDownload success. write_fw:1, 290ms
[   63.781358] RTL871X:  <=== rtl8188f_FirmwareDownload()
[   63.787263] RTL871X: HalDetectPwrDownMode(): PDN=0
[   63.792792] RTL871X: Set RF Chip ID to RF_6052 and RF type to 3.
[   64.355542] RTL871X: #### hw_var_set_opmode() -4815 iface_type(0) mode = 2 ####
[   64.364379] RTL871X: rtw_rf_get_kfree_tx_gain_offset path:0, ch:6, bb_gain_sel:0, kfree_offset:-1
[   64.375043] RTL871X: kfree gain_offset 0x55:0x82060
[   64.375965] RTL871X:  after :0x6050
[   64.385745] RTL871X: MAC Address = 94:a4:08:c5:12:65
[   64.392123] RTL871X: rtw_cfg80211_init_wiphy:rf_type=3
[   64.398443] RTL871X: start rtl8188fs_xmit_thread(wlan0)
[   64.404408] RTL871X: [HT] HAL Support STBC = 0x01
[   64.409931] RTL871X: -871x_drv - drv_open, bup=1
[   64.415666] RTL871X: cfg80211_rtw_set_power_mgmt(wlan0) enabled:1, timeout:-1
[   64.455109] RTL871X: cfg80211_rtw_flush_pmksa(wlan0)
[   64.513918] RTL871X: cfg80211_rtw_get_txpower
[   64.523822] RTL871X: (2)871x_drv - drv_close, bup=1, hw_init_completed=_TRUE
[   64.537694] RTL871X: -871x_drv - drv_close, bup=1



BusyBox v1.27.2 () built-in shell (ash)

 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 5C1C9C53)
 ----------------------------------------------
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/# mount
/dev/root on / type ext4 (ro,noatime)
devtmpfs on /dev type devtmpfs (rw,relatime,size=21096k,nr_inodes=5274,mode=755)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
none on /sys/kernel/config type configfs (rw,relatime)
adb on /dev/usb-ffs/adb type functionfs (rw,relatime)
/dev/mmcblk0p1 on /mnt/SDCARD type vfat (rw,relatime,fmask=0000,dmask=0000,allow_utime=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/# lsmod
8189fs               2324263  0
8723ds               2386937  0
fuse                  152450  0
gt9xxnew_ts            69396  0
ipt_REJECT              2647  0
iptable_filter          1759  0
xt_LOG                  1639  0
xt_TCPMSS               4060  0
xt_comment              1156  0
xt_limit                2725  0
xt_mac                  1338  0
xt_mark                 1472  0
xt_multiport            2489  0
xt_time                 3573  0
root@TinaLinux:/#
root@TinaLinux:/# ifconfig -a
lo        Link encap:Local Loopback
          LOOPBACK  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr 94:A4:08:C5:12:65
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@TinaLinux:/#

memory LV 7

WIFI 驱动参考 https://linux-sunxi.org/Wifi

RTL8189FTV
Driver has its own repository:

git clone https://github.com/jwrdegoede/rtl8189ES_linux.git
cd rtl8189ES_linux.git
git checkout -B rtl8189fs origin/rtl8189fs
make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux

复制到 lichee/linux-5.4/drivers/net/wireless/ 目录。

memory LV 7

前面有朋友说连不上 WIFI 热点，我试了一下，果然不行，楼主又挖坑啦。。。

那试一试这样吧：

mount -o remount -o rw /dev/root
/etc/init.d/wpa_supplicant start
wifi_connect_ap_test whycan 13800138000

这样应该问题不大了。

molin2050 LV 5

@memory 真的不怪他，毕竟坑网出来的

memory LV 7

源码patch： d1-mangopi_mq_source_patch_20211221_by_whycan.tgz

主要修改， etc/init.d/boot 脚本添加：

mount -o remount -o rw /dev/root

TF卡烧写固件：芒果派麻雀固件，支持WIFI 2021-12-21.img.7z

这个WIFI 应该 OK了：

wifi_connect_ap_test whycan 13800138000

memory LV 7

5寸 800x480 LCD 固件： tina_d1-mangopi_mq_rgb800x480_gt9xx_uart0_可能修复了某些显示屏问题_2021-12-24.7z

给麻雀做件衣裳
https://bbs.aw-ol.com/topic/816/share/9

kakatoo LV 4

此回复已被删除！

whycan晕哥 LV 9

周末整活，成功挽救这台伊拉克成色的15寸显示器于闲鱼市场：
https://bbs.aw-ol.com/topic/1293/share/38

参考这个帖子，感觉15寸 LVDS能玩起来。

wjp2547532 LV 6

我烧写的tina_d1-mangopi_mq_rgb800x480_gt9xx_uart0_20211214.img这个固件，现象如图，屏是和板子一起在淘宝买的，触摸也不能用，请问是固件用的不对么？

DOT小文哥 LV 8

@wjp2547532 在芒果派麻雀到手试玩中说：

这个固件，现象如图，屏是和板子一起在淘宝买的，触摸也不能用，请问是固件用的不对么？

淘宝哪里买的？什么型号？自带触摸模块吗？

wjp2547532 LV 6

@xiaowenge
https://item.taobao.com/item.htm?spm=a1z09.2.0.0.f3dd2e8d1ViEY2&id=638644511420&_u=5pf4hso07b4
这个链接，我看液晶上面贴了触摸屏

wjp2547532 LV 6

@xiaowenge 在芒果不鸽个人店买的芒果派哪吒MQ MangoPi 麻雀全志D1s F133 D1开发板RISCV

DOT小文哥 LV 8

呼叫芒果哥 @mangogeek

whycan晕哥 LV 9

@wjp2547532
你这个是电阻触摸屏吧，固件得自己捣鼓一下了，用D1s自带的电阻屏驱动程序。

wjp2547532 LV 6

@whycan 好的晕哥，那这屏幕显示的分辨率可能是咋回事，我烧写的固件就是800x480的

whycan晕哥 LV 9

@wjp2547532
这个屏幕分辨率可能是 480*272

wjp2547532 LV 6

@whycan 好的，那我一会用480*272的固件试一下

wjp2547532 LV 6

@whycan
用480*272的固件貌似更不靠谱，晕哥有这个屏的手册么

jr_online LV 7

@memory 大佬，linux新手如何基于这个固件快速进行二次开发呀，能指点一二吗？不知道如何下手，只会烧录大佬们的固件

whycan晕哥 LV 9

@jr_online
给D1 SDK 添加一个简单的helloworld package
https://bbs.aw-ol.com/topic/438

jr_online LV 7

@whycan 谢谢大佬指点，有关于lvgl8的开发指点吗，原谅我没学会走就想跑

whycan晕哥 LV 9

@jr_online

使用lvgl编写的2048小游戏(lv_lib_100ask_2048)
https://bbs.aw-ol.com/topic/1439

jr_online LV 7

@whycan 好的，大佬。我想请教个问题，就是这个芒果派wifi的，我烧录了tina_d1-mangopi_mq_rgb800x480_gt9xx_uart0_可能修复了某些显示屏问题_2021-12-24.img这个固件，那怎么进行wifi连接呢

whycan晕哥 LV 9

@jr_online

wifi_connect_ap_test 热点名密码：

wifi_connect_ap_test whycan 13800138000

jr_online LV 7

@whycan 好的好的，我试试。

jr_online LV 7

@whycan 可以连上了

jr_online LV 7

@whycan 大佬我又有个问题了，怎么把可执行文件传到板子上呀，有那些方式呢？

whycan晕哥 LV 9

@jr_online
adb push

jr_online LV 7

@whycan 报错没有设备

jr_online LV 7

@whycan 接上开发板后，在虚拟机上识别不了usb设备

whycan晕哥 LV 9

@jr_online
windows可以识别吗？

jr_online LV 7

@whycan 可以的喔，俺懂了，在Windows上安装adb工具.。谢谢大佬。

jr_online LV 7

@whycan 大佬，我应该怎么在宿主机上编译自己的lvgl项目呀，makefile不是很懂，请大佬指点一二

whycan晕哥 LV 9

@jr_online

这个比较简单：哪吒D1开发板 LVGL7 源码下载（带git仓库）

你先试一试。

jr_online LV 7

@whycan 好的，大佬，我说一下思路，请大佬指正：把这个源码解压之后，然后在这个目录下执行make，然后把生成的可执行文件adb push到板子上，然后./xxx。

DOT小文哥 LV 8

@jr_online 在芒果派麻雀到手试玩中说：

@whycan 好的，大佬，我说一下思路，请大佬指正：把这个源码解压之后，然后在这个目录下执行make，然后把生成的可执行文件adb push到板子上，然后./xxx。

adb push到板子上之后可能还要chmod 777

jr_online LV 7

@xiaowenge 收到

jr_online LV 7

@whycan @xiaowenge 大佬们，我又来了，把项目运行起来能显示了。但是触摸的的怎么加进去呀？

jr_online LV 7

@whycan 大佬，触摸屏怎么配置呀？想换个显示屏，换成st7701s的。该怎么配置呢？

whycan晕哥 LV 9

@jr_online
sipeed 开发板就是st7701s 的，可以参考一下：

https://bbs.sipeed.com/thread/1300

jr_online LV 7

@whycan 在芒果派麻雀到手试玩中说：

@jr_online
sipeed 开发板就是st7701s 的，可以参考一下：

https://bbs.sipeed.com/thread/1300

好的，大佬。

jr_online LV 7

此回复已被删除！

whycan晕哥 LV 9

@jr_online
windows 用 7z 解压第一个文件

jr_online LV 7

@whycan 在芒果派麻雀到手试玩中说：

@jr_online
windows 用 7z 解压第一个文件

明白了，感谢晕哥大佬

jr_online LV 7

@whycan 在芒果派麻雀到手试玩中说：

@jr_online
sipeed 开发板就是st7701s 的，可以参考一下：

https://bbs.sipeed.com/thread/1300

大佬，我还在弄用芒果派mq通过rgb接口驱动st7701s屏的，我怎么才能知道这屏幕驱动有没有编译呀？

jr_online LV 7

@whycan 晕哥，我现在把st7701s屏的驱动弄好，相关板级配置文件也改了，然后编译镜像进去了，但是板子上没有调用到。想问一下这个板子是执行流程是怎样的呢？屏相关的驱动是在哪里调用的，刚接触真的一脸懵逼，求大佬解惑！

whycan晕哥 LV 9

@jr_online
在 u-boot 里面调试，可以输出一些调试信息，一般在u-boot开屏之后，Linux不再自动开屏了。

可以接个逻辑分析仪看下时序。

jr_online LV 7

@whycan 在u-boot里面调试：是要把屏驱动放在 lichee/brandy-2.0/u-boot-2018/drivers/video/sunxi/disp2/disp/lcd底下吗？我刚刚发现一个问题，是不是要修改device/config/chips/d1/configs/mangopi_mp_rgb800x480_gt9xx/linux-5.4文件夹底下的config-5.4配置文件是不是也要修改呢？

jr_online LV 7

@whycan 大佬，是不是我需要重新编译一下u-boot才行呀？u-boot那边还是默认的lcd?怎么去编译这个u-boot呢？

whycan晕哥 LV 9

@jr_online
还要配置 uboot-board.dts。
linux的驱动和 board.dts 暂时可以不用配置。

重新编译boot命令： mboot

jr_online LV 7

@whycan
好滴，大佬！

jr_online LV 7

@whycan
大佬，我把屏接上还是没反应，接了逻辑分析仪抓了st7701s初始化引脚的时序，一直是拉高的。是不是我用的gpio被占用了呀？我用的是P3的PE8-11。
31a11e14-009d-4ae9-bbde-19026b7cb06b-1653479774644_B9350CCC-3235-4df1-B976-BB526DE8F081.png

uboot-board.dts是这样配置gpio的 :
dbf562a2-0630-44a6-a0d4-e7eaf24028fa-1653479916652_640E268E-48C2-4d3b-B39D-ED1FB50CEFE1.png

whycan晕哥 LV 9

@jr_online
那个 default_panel地方改成你注册的驱动了吗？

jr_online LV 7

@whycan 在芒果派麻雀到手试玩中说：

default_panel

大佬，default_panel在那个地方改呀？我好像找不到注册驱动的地方

jr_online LV 7

@whycan
大佬，是这个地方吗？
2010b243-8ea6-4d79-8596-884153edadc2-lQLPJxZXftzgOQDNAsjNAhSw0cNWRlAnT1cCkGtF1UDnAA_532_712.png

jr_online LV 7

@whycan
大佬，您看一下，这个打印出来的信息

whycan晕哥 LV 9

@jr_online
看下有没有参与编译，调试语句有没有执行。

jr_online LV 7

@whycan
有.o文件生成，应该是参与编译了。但是没有屏驱动的调试语句打印出来。应该是没有执行到屏驱动
还有就是编译的时候有一个警告：
05dc2b1b-caae-496a-aa6b-d74b1ba68336-lQLPJxZXZVxhC93Mlc0DjLBeRXU8PBeXmgKQQX05gLwA_908_149.png

jr_online LV 7

@whycan 大佬，我能点亮st7701s了,但是分辨率我修改了对应的参数，还是显示错乱，想请教一下，还有哪里修改参数的地方需要留意吗？

whycan晕哥 LV 9

@jr_online
uboot-board.dts lcdX 节点修改为屏幕的分辨率，

初始化代码也要改成屏幕的分辨率，

这样就能对得上了。

jr_online LV 7

@whycan
回老大，uboot-board.dts 我是修改了对应屏幕的分辨率，但是你说的初始化代码也要改是指屏参是吗？
这是现在的现象，屏幕是竖屏的，但现在是横屏显示了：
fde6ac45-c97f-4585-a2ca-f474fc04da7e-lADPJxDjyGNmj4PND8DNC9A_3024_4032.jpg

whycan晕哥 LV 9

@jr_online
问厂家要初始化代码和屏幕手册。

jr_online LV 7

@whycan 大佬，现在就是根据厂家给的初始化代码来调的

jr_online LV 7

@whycan 大佬，我现在得能显示正常了，但是运行lvgl的demo，触摸没反应。但是通过getevent进行调试发现，是有触摸的数据打印出来的。求助大佬！

jr_online LV 7

@whycan 大佬，我的触摸还是没能联动lvgl，在lv_drv_conf.h里也改成对应的"/dev/input/event2"，然后通过getevent也有触摸数据打印，但是lvgl触摸就是没反应。电容屏是不需要校准的吧。救救孩子吧！

a892755772 LV 5

@wjp2547532 您好我屏幕也碰到相同的问题显示不全又花请问您有解决吗

wjp2547532 LV 6

@a892755772 还没呢，前几天最近没啥时间弄，扔在那了，过几天有时间了再看

wjp2547532 LV 6

大佬，请教一下，这是因为没有权限么，然后怎么才能获得root权限呢，烧写的是tina_d1-mangopi_mq_rgb800x480_gt9xx_uart0_20211214.img这个固件

soso90 LV 7

@jr_online 我用到的是方屏，也是和你一样，lvgl花屏，然后其他显示显示的是变成上下分屏，内容一致，要修改哪里？uboot的分辨率没同步设置？我这边是关了uboot的lcd驱动的

jr_online LV 7

@soso90 在芒果派麻雀到手试玩中说：

@jr_online 我用到的是方屏，也是和你一样，lvgl花屏，然后其他显示显示的是变成上下分屏，内容一致，要修改哪里？uboot的分辨率没同步设置？我这边是关了uboot的lcd驱动的

你可以参考一下这个：
https://blog.csdn.net/qq_34440409/article/details/122021748?spm=1001.2101.3001.6650.5&utm_medium=distribute.pc_relevant.none-task-blog-2~default~BlogCommendFromBaidu~Rate-5-122021748-blog-119254978.pc_relevant_paycolumn_v3&depth_1-utm_source=distribute.pc_relevant.none-task-blog-2~default~BlogCommendFromBaidu~Rate-5-122021748-blog-119254978.pc_relevant_paycolumn_v3&utm_relevant_index=7

captain LV 5

@memory 在芒果派麻雀到手试玩中说：

WIFI 驱动参考 https://linux-sunxi.org/Wifi
RTL8189FTV
Driver has its own repository:

git clone https://github.com/jwrdegoede/rtl8189ES_linux.git
cd rtl8189ES_linux.git
git checkout -B rtl8189fs origin/rtl8189fs
make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux

复制到 lichee/linux-5.4/drivers/net/wireless/ 目录。

根据这个方法，移植到T113_longin 。
报错：

linux-5.4/drivers/net/wireless/rtl8189fs/core/rtw_cmd.c:22:23: fatal error: drv_types.h: No such file or directory

查看了一下，它是有这个文件的。

zhangwei LV 5

@captain 你好，请问缺少drv_types.h问题解决了吗，我在移植8723DS的时候，也遇到类似问题。

soso90 LV 7

@memory

@memory 在芒果派麻雀到手试玩中说：

WIFI 驱动参考 https://linux-sunxi.org/Wifi

RTL8189FTV
Driver has its own repository:

git clone https://github.com/jwrdegoede/rtl8189ES_linux.git
cd rtl8189ES_linux.git
git checkout -B rtl8189fs origin/rtl8189fs
make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux

复制到 lichee/linux-5.4/drivers/net/wireless/ 目录。

我编译之后，插入驱动，没有报错。也没有wlan0出来，是不是dts没有改导致，dts需要修改什么

soso90 LV 7

@soso90 在芒果派麻雀到手试玩中说：

@memory

@memory 在芒果派麻雀到手试玩中说：

WIFI 驱动参考 https://linux-sunxi.org/Wifi

RTL8189FTV
Driver has its own repository:

git clone https://github.com/jwrdegoede/rtl8189ES_linux.git
cd rtl8189ES_linux.git
git checkout -B rtl8189fs origin/rtl8189fs
make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux

复制到 lichee/linux-5.4/drivers/net/wireless/ 目录。

我编译之后，插入驱动，没有报错。也没有wlan0出来，是不是dts没有改导致，dts需要修改什么

驱动采用ko方式，插入只打印这个。。。

root@(none):/# insmod  /usr/lib/8189fs.ko
[   45.485465] 8189fs: loading out-of-tree module taints kernel.




[   61.807694] RTW: module init start
[   61.811721] RTW: rtl8189fs v5.7.9_35795.20191128
[   61.817068] RTW: build time: Aug 12 2022 14:08:42
[   61.822561] RTW: rtw_inetaddr_notifier_register
[   61.828244] RTW: module init ret=0
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/#
root@TinaLinux:/# ifconfig -a
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:144 errors:0 dropped:0 overruns:0 frame:0
          TX packets:144 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:11232 (10.9 KiB)  TX bytes:11232 (10.9 KiB)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

daMing123 LV 5

@soso90 我也是这样，你是如何解决的？

soso90 LV 7

@daming123 没有解决，哈哈。你要是搞定分享一下方法。硬件是没问题。烧官方固件是有wifi。这个问题鸽了很久。会不会是dts没配置好。可以对比芒果的固件dts。期待你解决~