全志在线开发者论坛

柚木鉉

@dream 甚至是openWrt通病了hhhhh

柚木鉉

OpenixCard V1.1.5 更新了

OpenixCard -u  <img>   - 解包全志镜像
OpenixCard -uc <img>   - 解包全志镜像并输出分区表
OpenixCard -d  <img>   - 转换全志镜像到普通镜像
OpenixCard -p  <dir>   - 打包解包的的镜像
OpenixCard -s  <img>   - 获取全志镜像真实大小

柚木鉉

@tigger 全系适用的

柚木鉉

换 VirtualBox（不是

柚木鉉

@aldfaaa 换ubuntu18.04

柚木鉉

烧录教程

线刷固件：

1）插入格式化好的 SD 卡（不论线刷还是卡刷）

2）使用 PhoenixSuit 刷机即可

卡刷固件：

1）使用 Win32diskimager、etcher等软件刷卡后插入开发板上电启动

PhoenixCard固件：

1）使用 PhoenixCard 刷卡后插入开发板上电启动

柚木鉉

Welcome to Debian GNU/Linux!

测试固件：

用户名：root，密码：awol

Debian 9

2022-07-04-14-30
- 线刷（无法登陆）：v853_linux_vision_debian_uart0.7z
- 2022-07-05-09-29-卡刷：v853_debian_vision.tar.gz

Debian + LXDE + Python

2022-07-06
- 链接：https://pan.baidu.com/s/1AZzKlFICjOc4FZfkmEm8jQ
- 提取码：awol
- PhoenixCard 固件

柚木鉉

@soso90
你用的是135240的驱动，要改成240240的驱动

1）修改这里的偏移

static void fbtft_set_addr_win(struct fbtft_par *par, int xs, int ys, int xe,
			       int ye)
{
	switch(par->info->var.rotate)
	{
		case   0: xs+=53;xe+=53;ys+=40;ye+=40;
				 break;
		case  90: xs+=40;xe+=40;ys+=53;ye+=53;
				 break;
		case 180: xs+=53;xe+=53;ys+=40;ye+=40;
				 break;
		case 270: xs+=40;xe+=40;ys+=53;ye+=53;
				 break;
		default :
				 break;
	}

	write_reg(par, MIPI_DCS_SET_COLUMN_ADDRESS,
		  (xs >> 8) & 0xFF, xs & 0xFF, (xe >> 8) & 0xFF, xe & 0xFF);

	write_reg(par, MIPI_DCS_SET_PAGE_ADDRESS,
		  (ys >> 8) & 0xFF, ys & 0xFF, (ye >> 8) & 0xFF, ye & 0xFF);

	write_reg(par, MIPI_DCS_WRITE_MEMORY_START);
}

2）修改这里的初始化代码，我这里的是135*240的

static int init_display(struct fbtft_par *par)
{
    par->fbtftops.reset(par);
    mdelay(50);
    write_reg(par,0x36,0x00);
    write_reg(par,0x3A,0x05);
    write_reg(par,0xB2,0x0C,0x0C,0x00,0x33,0x33);
    write_reg(par,0xB7,0x35);
    write_reg(par,0xBB,0x19);
    write_reg(par,0xC0,0x2C);
    write_reg(par,0xC2,0x01);
    write_reg(par,0xC3,0x12);
    write_reg(par,0xC4,0x20);
    write_reg(par,0xC6,0x0F);
    write_reg(par,0xD0,0xA4,0xA1);
    write_reg(par,0xE0,0xD0,0x04,0x0D,0x11,0x13,0x2B,0x3F,0x54,0x4C,0x18,0x0D,0x0B,0x1F,0x23);
    write_reg(par,0xE1,0xD0,0x04,0x0C,0x11,0x13,0x2C,0x3F,0x44,0x51,0x2F,0x1F,0x1F,0x20,0x23);
    write_reg(par,0x21);
    write_reg(par,0x11);
    mdelay(50);
    write_reg(par,0x29);
    mdelay(200);
    return 0;
}

3）修改这里屏幕分辨率

static struct fbtft_display display = {
	.regwidth = 8,
	.width = 135,
	.height = 240,
	.gamma_num = 2,
	.gamma_len = 14,
	.gamma = DEFAULT_GAMMA,
	.fbtftops = {
		.init_display = init_display,
		.set_var = set_var,
		.set_gamma = set_gamma,
		.blank = blank,
	},
};

以上资料屏幕厂商会提供

柚木鉉

H6
H616
A10
A20

柚木鉉

@wyljkl 开机logo是保存在boot-resource分区内的，在Linux系统中挂载这个分区，替换开机logo即可

柚木鉉

@soso90 错位改成卖家给的资料包里的偏移，这个屏幕我买过几家不同的，初始化偏移都不太一样

柚木鉉

@haiqianghuang69 参考sunxi_flash，我用的是这个

柚木鉉

@wyljkl 解决了

柚木鉉

xfel

用 MSVC2017 编译 XFEL 项目

柚木鉉

软件包：lvgl-8

修改了 # define LV_DEMO_MUSIC_AUTO_PLAY 1 但是重新make系统这个软件没有重新编译，放板子是运行的还是原来编译的。

柚木鉉

@xiaowenge

柚木鉉

@mxlol233

#define C910_PLIC_CLINT_OFFSET            0x04000000  /* 64M */
plic_base_addr = csr_read(CSR_PLIC_BASE);
clint_base_addr = plic_base_addr + C910_PLIC_CLINT_OFFSET;

柚木鉉

抄DDR模板可以吧

柚木鉉

正常情况

------run rc.modules file-----
[    4.303240] ======== XRADIO WIFI OPEN ========
[    4.308485] [XRADIO] Driver Label:XR_V02.16.91 _HT40_01.33  Jun 17 2022 01:10:45
[    4.317160] [XRADIO] Allocated hw_priv @ dec24c80
[    4.322655] [XRADIO_ERR] Access_file failed, path:/data/misc/wifi/xr_wifi.conf!
[    4.331961] sunxi-wlan soc@03000000:wlan@0: bus_index: 1
[    4.340070] sunxi-wlan soc@03000000:wlan@0: check wlan wlan_power voltage: 3300000
[    4.350205] sunxi-wlan soc@03000000:wlan@0: check wlan io_regulator voltage: 3300000
[    4.469284] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    4.479542] [XRADIO] Detect SDIO card 1
[    4.523933] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    4.564541] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    4.577752] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    4.598762] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    4.609485] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    4.620492] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    4.632248] mmc2: new high speed SDIO card at address 0001
[    4.639063] [SBUS] XRadio Device:sdio clk=50000000
[    4.645270] [XRADIO] XRADIO_HW_REV 1.0 detected.
[    4.724339] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[    4.766101] [XRADIO] Bootloader complete
[    4.854731] [XRADIO] Firmware completed.
[    4.860479] [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[    4.877907] [XRADIO] Firmware Startup Done.
[    4.882880] [XRADIO_WRN] enable Multi-Rx!

柚木鉉

配上3.49寸长条屏幕

柚木鉉

传统艺能不能丢（

柚木鉉

完工，全部功能验证完成。

柚木鉉

验证了：

DDR3 1866
TF挂载
eMMC启动
GPIO使用
i2c、spi功能
UART转接芯片

WiFi还有问题，SDIO扫不到卡：https://bbs.aw-ol.com/topic/1675/share/1

柚木鉉

[    6.710506] ======== XRADIO WIFI OPEN ========
[    6.715506] [XRADIO] Driver Label:XR_V02.16.91 _HT40_01.33  Jun 28 2022 09:26:33
[    6.723995] [XRADIO] Allocated hw_priv @ dec4cc80
[    6.729570] [XRADIO_ERR] Access_file failed, path:/data/misc/wifi/xr_wifi.conf!
[    6.738495] sunxi-wlan soc@03000000:wlan@0: bus_index: 1
[    6.745961] sunxi-wlan soc@03000000:wlan@0: check wlan wlan_power voltage: 3300000
[    6.755845] sunxi-wlan soc@03000000:wlan@0: check wlan io_regulator voltage: 3300000
[    6.874763] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.885036] [XRADIO] Detect SDIO card 1
[    6.928984] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.969221] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    6.975368] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    6.981256] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.994460] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.006546] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.012648] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.018822] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.024871] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.030664] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    7.041993] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.078945] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.119297] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    7.125537] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    7.131427] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.144761] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.156934] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.163120] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.169254] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.175388] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.181168] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    7.192497] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.228938] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.269470] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    7.275888] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    7.281767] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.295346] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.307708] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.314058] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.320370] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.326679] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.332459] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    7.343793] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.378942] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.419990] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    7.426925] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    7.432806] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.447142] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    7.460086] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.468501] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.475341] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.482182] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    7.487960] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    9.069817] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.080087] [XRADIO] Remove SDIO card 1
[    9.094398] [SBUS_ERR] sdio probe timeout!
[    9.099022] [XRADIO_ERR] sbus_sdio_init failed
[    9.105100] ======== XRADIO WIFI OPEN ========
[    9.110380] [XRADIO] Driver Label:XR_V02.16.91 _HT40_01.33  Jun 28 2022 09:26:33
[    9.118725] [XRADIO] Allocated hw_priv @ de7ecc80
[    9.124066] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.135109] [XRADIO_ERR] Access_file failed, path:/data/misc/wifi/xr_wifi.conf!
[    9.144086] sunxi-wlan soc@03000000:wlan@0: bus_index: 1
[    9.150416] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.156572] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.162517] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.174162] sunxi-wlan soc@03000000:wlan@0: check wlan wlan_power voltage: 3300000
[    9.184142] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.195882] sunxi-wlan soc@03000000:wlan@0: check wlan io_regulator voltage: 3300000
[    9.204916] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.211016] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.217077] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.223142] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.228938] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    9.250012] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.308949] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.359307] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.365543] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.371432] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.388190] [XRADIO] Detect SDIO card 1
[    9.405358] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.417635] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.423806] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.430001] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.436127] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.441927] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    9.453285] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.488963] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.529481] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.535890] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.541770] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.555362] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.567787] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.574102] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.580428] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.586726] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.592522] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    9.603861] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.638945] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.680002] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.686935] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.692814] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.707148] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.720127] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.726952] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.733792] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.740633] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.746420] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    9.757779] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.788942] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.829215] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.835362] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.841240] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.854453] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.866665] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.872749] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.878803] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.884892] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[    9.890692] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    9.902052] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.938961] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    9.979310] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.985547] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[    9.991426] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.004761] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.016988] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.023129] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.029286] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.035415] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.041194] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   10.052528] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.088972] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.129479] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[   10.135891] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[   10.141789] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.155366] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.167773] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.174084] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.180399] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.186698] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.192487] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   10.203821] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.238944] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.279997] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[   10.286930] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[   10.292818] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.307146] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   10.320123] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.326957] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.333787] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.340606] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RE !!
[   10.346390] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   10.579102] random: crng init done
[   10.582919] random: 1 urandom warning(s) missed due to ratelimiting
[   11.549825] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   11.560121] [XRADIO] Remove SDIO card 1
[   11.574416] [SBUS_ERR] sdio probe timeout!
[   11.579034] [XRADIO_ERR] sbus_sdio_init failed

柚木鉉

H616需要与全志签订商务NDA后申请，平台上有申请流程，详见：open.allwinnertech.com

柚木鉉

@efancier 不发

柚木鉉

@a892755772 我的修改的dts就是默认的

柚木鉉

试试修改设备树看看是不是那个问题，不过我这里测试这个屏幕没这个问题，不会花

柚木鉉

@y97788 没有扫到i2c设备，检查下线有没有jie dui

柚木鉉

@y97788 调低loglevel=1
现在没法看了

柚木鉉

@apollo5520 测不到信号就不是这个问题了，加载驱动的时候默认会打开dxco。我那个问题是信号噪音过大的问题

柚木鉉

i2cdetect看看，记得loglevel=1

柚木鉉

@mxlol233 更新buildroot 2022.05就ok了

柚木鉉

@apollo5520 用1k电阻接地了

柚木鉉

@yelong98 支持的

柚木鉉

@whycan 家境贫寒，告辞

柚木鉉

@jr_online
Target Images --->
[*] squashfs --->

柚木鉉

@tigger 绝赞

柚木鉉

加压能不能上1G

柚木鉉

单个kmalloc一般最大4MB，过大换vmalloc比较好

柚木鉉

好像没看到什么错误

柚木鉉

Linux嵌入式不太懂，有没有人教教我可以怎么学习？

柚木鉉

XR829 使用 40M 晶振与使用 24M 晶振有什么区别
https://bbs.aw-ol.com/topic/1228/share/3

柚木鉉

bootargs里修改mtd设备，或者用ubi

在env.cfg里

柚木鉉

@a892755772 估计是uboot disp的驱动问题，我之后再看看

柚木鉉

@a892755772

cat /dev/urandom > /dev/fb0 之后屏幕会不会花屏，这里说的花屏是雪花屏不是上面那个还能看出图形的，cat: write error: No space left on device 那个不是报错是正常情况

柚木鉉

@a892755772 这样还是花屏吗
cat /dev/urandom > /dev/fb0

柚木鉉

有没有sync_update

柚木鉉

@a892755772 什么版本？看这个Commit ba93df0b

 _____ _____ ___    __ __             _   _ _____ _____ _____
| __  | __  |_  |  |  |  |_ _ ___ _ _| |_|_|   __| __  |     |
| __ -|    -|  _|  |_   _| | |- _| | | '_| |__   | __ -|   --|
|_____|__|__|___|    |_| |___|___|___|_,_|_|_____|_____|_____|
Commit:      ba93df0b

柚木鉉

@a892755772 更新Buildroot-YuzukiSBC，运行sync_update 命令

柚木鉉

改为ext4 文件系统

柚木鉉

噢噢噢噢来了来了

柚木鉉

@shz18877605430 我一般就重新换一个dtc版本了hhh

柚木鉉

@shz18877605430 估计是中断的写法不一样？

柚木鉉

果然是线序不一样，理论上发0x11，0x29至少得亮了hhhh

柚木鉉

@efancier 不接也可以

柚木鉉

不错诶！！！！！

柚木鉉

@xiaowenge hhhhhh

柚木鉉

@liuxingkeji 主要是资料不太对

柚木鉉

没反应+1，初始化序列好像不对，发送0x29没反应

柚木鉉

发一个内存模板

测试DDR3 1866没问题，PCB是从LCEDA导出的，JLC打板子选择2313

V853_DRAM.pcbdoc

注意：

因格式和图元的设计不一致，格式转换会有一定的差异，导出后请务必在 Altium Designer 仔细检查。
导出前请务必阅读：导出 Altium Designer注意事项与免责声明
不承担因导出差异导致的任何生产损失。

柚木鉉

@mangogeek 华秋太草了

柚木鉉

@yuzukitsuru
内存跑到了1866

柚木鉉

启动了！内存没啥大问题了

[26182]fes begin commit:fbe7448cdb
[26185]set pll start
[26187]periph0 has been enabled
[26190]set pll end
[26193]PMU: AXP21
[26196]board init ok
[26198]beign to init dram
[26200]DRAM use external ZQ!!
[26203]chip id check OK
[26206]DRAM_VCC set to 1500 mv
[26209]trefi:7.8ms
[26211][AUTO DEBUG] single rank and full DQ!
[26216]trefi:7.8ms
[26218][AUTO DEBUG] rank 0 row = 15 
[26222][AUTO DEBUG] rank 0 bank = 8 
[26225][AUTO DEBUG] rank 0 page size = 2 KB 
[26229]DRAM BOOT DRIVE INFO: V0.16
[26232]DRAM CLK = 936 MHz
[26235]DRAM Type = 3 (2:DDR2,3:DDR3)
[26238]DRAMC ZQ value: 0x7b7bfb
[26241]DRAM ODT value: 0x42.
[26245]DRAM SIZE =512 M
[26247]dram_tpr4:0x0
[26250]DRAM simple test OK.
[26253]rtc standby flag is 0x0, super standby flag is 0x0
[26258]init dram ok



U-Boot 2018.05-00006-gb5e4c9f6fb (Jun 09 2022 - 06:47:31 +0000) Allwinner Technology

[27.808]CPU:   Allwinner Family
[27.811]Model: sun8iw21
I2C:   ready
[27.837]DRAM:  512 MiB
[27.840]Relocation Offset is: 1ced0000
[27.865]secure enable bit: 0
[27.867]PMU: AXP21
[27.869]PMU: pmu_axp2101 found
[27.872]BMU: AXP21
[27.874]BMU: bmu_axp2101 found
FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_INTERNAL
[27.884]gpio_bias, pc_bias: 1800, pc_supply: not set  
[27.889]gpio_bias, pl_bias:   -1, pl_supply: not set  
[27.895]dcdc1_vol = 3300, onoff=1
[27.898]dcdc2_vol = 900, onoff=1
[27.901]dcdc5_vol = 0, onoff=0
[27.905]aldo1_vol = 1800, onoff=1
[27.908]aldo2_vol = 1800, onoff=1
[27.912]aldo3_vol = 3300, onoff=1
[27.915]aldo4_vol = 3300, onoff=1
[27.919]bldo1_vol = 1800, onoff=1
[27.922]bldo2_vol = 2800, onoff=1
[27.926]dldo1_vol = 3300, onoff=1
[27.929]dldo2_vol = 1200, onoff=1
bias_name:pc_bias	 bias_vol:1800
bias_name:pi_bias	 bias_vol:1800
[27.939]bat_vol=4577, ratio=1
[27.942]safe_vol=3500, safe_ratio=1
[27.946]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz  MBus=300Mhz
[27.952]gic: normal mode
sunxi flash map init
[27.957]flash init start
[27.959]workmode = 16,storage type = 0
try card 2
set card number 2
get card number 2
[27.967][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00
[27.972][mmc]: get sdc_type fail and use default host:tm4.
[27.979][mmc]: Is not Boot mode!
[27.982][mmc]: SUNXI SDMMC Controller Version:0x50400
[27.993][mmc]: ************Try SD card 2************
[27.998][mmc]: mmc 2 cmd timeout 100 status 100
[28.002][mmc]: smc 2 err, cmd 8,  RTO
[28.006][mmc]: mmc 2 close bus gating and reset
[28.011][mmc]: mmc 2 cmd timeout 100 status 100
[28.015][mmc]: smc 2 err, cmd 55,  RTO
[28.018][mmc]: mmc 2 close bus gating and reset
[28.023][mmc]: ************Try MMC card 2************

[28.079][mmc]: mmc 2 cmd timeout 100 status 100
[28.083][mmc]: smc 2 err, cmd 8,  RTO
[28.086][mmc]: mmc 2 close bus gating and reset
[28.091][mmc]: mmc 2 cmd timeout 100 status 100
[28.095][mmc]: smc 2 err, cmd 55,  RTO
[28.099][mmc]: mmc 2 close bus gating and reset
[28.115][mmc]: gen_tuning_blk_bus8: total blk 10
[28.119][mmc]: gen_tuning_blk_bus4: total blk 6
[28.124][mmc]: Using 8 bit tuning now
[28.127][mmc]: send stop
[28.129][mmc]:  Write tuning pattern failded
[28.133][mmc]: Using 8 bit tuning now
[28.137][mmc]: send stop
[28.139][mmc]:  Write tuning pattern failded

[28.143][mmc]: Write pattern failed
[28.146][mmc]: mmc init product failed
MMC init failed
try emmc fail
[28.153]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106
[28.158]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217
[28.167]sunxi-spinand-phy: request spi0 gpio ok
[28.171]sunxi-spinand-phy: request general tx dma channel ok!
[28.176]sunxi-spinand-phy: request general rx dma channel ok!
[28.182]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[28.186]sunxi-spinand-phy: init spic0 clk ok
[29.190]sunxi-spinand-phy: read id failed : -110
try nand fail
[29.198]unrecognized JEDEC id bytes: ff, ff, ff
data abort
pc : [<5ff0b602>]	   lr : [<5ff0b5e9>]
reloc pc : [<4303b602>]	   lr : [<4303b5e9>]
sp : 5de6dc38  ip : 0000000c	 fp : 43000508
r10: 43031ca1  r9 : 5deafe70	 r8 : 5deff8a8
r7 : 5ff7f2e8  r6 : ffffffed	 r5 : 5ff4fbe0  r4 : 5deff8f0
r3 : 00002000  r2 : 00000001	 r1 : 0000000a  r0 : 00000030
Flags: nZCv  IRQs on  FIQs off  Mode SVC_32

柚木鉉

推荐一颗单颗2G的芯片：D9STR，测试可以跑到1866，单帖就OK
或者双贴单颗1G单Die的芯片，D9STQ，测试1600没问题

柚木鉉

@apollo5520 内存控制的源码是不开源的，只有二进制发布。DRAM参数设置在sys_config.fex内，libdram会读取这个配置文件所以也不需要调试dram代码。

;sdram configuration

另外H5TC8G63CMR是Dual Die Package。意思是一颗内存内其实有2片die，所以一颗内存等于2颗单Die的内存，占用了所有CS线。D1-H 芯片支持双贴单Die的DRAM、同时也支持单帖双Die的DRAM，最大16Gb。

柚木鉉

进入Linux内也是1G吗？

柚木鉉

@efancier buildroot更新了，修复了i2c，de，uart等一堆问题，source envsetup.sh 更新然后重新make xxxx_defconfig就行了

柚木鉉

换成4G内存应该不会启动，两个的地址控制线不太一样。
fel进入模式是可以hook出来的，例如这里的识别到uart即进入fel

柚木鉉

@efancier 软件相同硬件也相同吗？估计问题不在delay上

柚木鉉

8125我记得是有内置delay的，delay配置删了试试看

柚木鉉

@daming123 我这里没有这个屏幕，也不清楚是什么问题

柚木鉉

解决了，示波器测量发现过充，电阻解决


[   15.077675] ======== XRADIO WIFI OPEN ========
[   15.086009] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[   15.093245] [XRADIO] Allocated hw_priv @ (____ptrval____)
[   15.101203] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[   15.119168] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[   15.289156] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   15.427605] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   15.439043] [XRADIO] Detect SDIO card 1
[   15.461469] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   15.491817] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   15.525136] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   15.540610] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   15.567424] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   15.579332] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   15.591648] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[   15.605149] mmc2: new high speed SDIO card at address 0001
[   15.613632] [SBUS] XRadio Device:sdio clk=50000000
[   15.621530] [XRADIO] XRADIO_HW_REV 1.0 detected.
[   15.772529] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[   15.927766] [XRADIO] Bootloader complete
[   16.099634] [XRADIO] Firmware completed.
[   16.105809] [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[   16.124345] [XRADIO] Firmware Startup Done.
[   16.129480] [XRADIO_WRN] enable Multi-Rx!
[   16.139231] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.169753] xt_time: kernel timezone is -0000

柚木鉉

@daming123 我这里没有这个屏幕，也不清楚是什么问题

柚木鉉

正常情况

root@TinaLinux:/lib/modules/5.4.61# insmod xr829.ko
======== XRADIO WIFI OPEN ========
[XRADIO_ERR] debugfs isnot initialized
[XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[XRADIO] Allocated hw_priv @ 0000000035532399
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[XRADIO] Detect SDIO card 1
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO] XRADIO_HW_REV 1.0 detected.
[XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[XRADIO] Bootloader complete
[XRADIO] Firmware completed.
[WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09
[XRADIO] Firmware Startup Done.
[XRADIO_WRN] enable Multi-Rx!
ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
···

柚木鉉

@whycan
找了一个好的板子拆了晶振是这样的

root@TinaLinux:/lib/modules/5.4.61# insmod xr829.ko
======== XRADIO WIFI OPEN ========
[XRADIO_ERR] debugfs isnot initialized
[XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[XRADIO] Allocated hw_priv @ 00000000e2194bdf
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[XRADIO] Detect SDIO card 1
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO] XRADIO_HW_REV 1.0 detected.
[XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding.
[XRADIO_ERR] Device will restart at 1 times!
sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
mmc1: card 0001 removed
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[XRADIO] Remove SDIO card 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[XRADIO] Detect SDIO card 1
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO] XRADIO_HW_REV 1.0 detected.
[XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding.
[XRADIO_ERR] Device will restart at 2 times!
sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
mmc1: card 0001 removed
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[XRADIO] Remove SDIO card 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[XRADIO] Detect SDIO card 1
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO] XRADIO_HW_REV 1.0 detected.
[XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding.
[XRADIO_ERR] Device will restart at 3 times!
sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
mmc1: card 0001 removed
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[XRADIO] Remove SDIO card 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[XRADIO] Detect SDIO card 1
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO] XRADIO_HW_REV 1.0 detected.
^C[XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding.
[XRADIO_ERR] Device will restart at 4 times!
sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
[XRADIO] Remove SDIO card 1
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
mmc1: card 0001 removed
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
mmc1: new high speed SDIO card at address 0001
[XRADIO] Detect SDIO card 1
[SBUS] XRadio Device:sdio clk=50000000
[XRADIO_ERR] xradio_register_bh failed(-4).
sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
[XRADIO] Remove SDIO card 1
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !!
mmc1: card 0001 removed
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
^Csunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
xradio_core_init failed (-4)!
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!

柚木鉉

@daming123 ?????可还行

柚木鉉

@whycan
~~降速了好像也没有用~~

io绑错了

[   19.052197] ======== XRADIO WIFI OPEN ========
[   19.057744] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[   19.064598] [XRADIO] Allocated hw_priv @ (____ptrval____)
[   19.072289] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[   19.097764] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[   19.307190] sunxi_hosts[1] should not be null
[   19.307197] [XRADIO] Detect SDIO card 1
[   21.361925] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
[   21.469153] sunxi_hosts[1] should not be null
[   21.469161] [XRADIO] Remove SDIO card 1
[   21.488339] [SBUS_ERR] sdio probe timeout!
[   21.492954] [XRADIO_ERR] sbus_sdio_init failed
[   21.499076] xradio_core_init failed (-110)!

柚木鉉

@daming123 brandy-2.0/u-boot-2018/configs/sun20iw1p1_defconfig 注释掉 #CONFIG_DISP2_SUNXI=y，使用kernel初始化屏幕测试

柚木鉉

量了一下好像内置REFCLK_OUT没有输出，但是我这个探头电容很大，可能会导致这个问题

柚木鉉

柚木鉉

[   15.763263][   15.763263] ======== XRADIO WIFI OPEN ========
[   15.770569][   15.770569] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[   15.779230][   15.779230] [XRADIO] Allocated hw_priv @ (____ptrval____)
[   15.788116][   15.788116] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[   15.806534][   15.806534] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[   16.158083][   16.158083] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   16.170922][   16.170922] [XRADIO] Detect SDIO card 1
[   16.181998][   16.181998] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   16.209670][   16.209670] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   16.233815][   16.233815] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   16.252653][   16.252653] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   16.279628][   16.279628] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   16.293081][   16.293081] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   16.306785][   16.306785] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[   16.324944][   16.324944] mmc2: new high speed SDIO card at address 0001
[   16.343747][   16.343747] [SBUS] XRadio Device:sdio clk=50000000
[   16.360502][   16.360502] [XRADIO] XRADIO_HW_REV 1.0 detected.
[   16.483883][   16.483883] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[   16.593457][   16.593457] [XRADIO] Bootloader complete
[   17.138413][   17.138413] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   17.571269][   17.571269] [XRADIO_ERR] xradio_firmware: wait for download completion failed. Read: 0xFFFFFFFF
[   17.594485][   17.594485] [XRADIO_ERR] xradio_load_firmware: can't download firmware.
[   17.603764][   17.603764] [XRADIO_ERR] xradio_load_firmware failed(-110).
[   17.613037][   17.613037] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
[   17.748248][   17.748248] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   17.756403][   17.756403] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   17.764552][   17.764552] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   17.772665][   17.772665] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   17.781030][   17.781030] mmc2: card 0001 removed
[   17.786530][   17.786530] [XRADIO] Remove SDIO card 1
[   17.792516][   17.792516] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   17.828132][   17.828132] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   17.849201][   17.849201] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   17.859197][   17.859197] xradio_core_init failed (-110)!
[   17.878141][   17.878141] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   17.904007][   17.904007] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[   17.913008][   17.913008] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[   17.921267][   17.921267] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   17.937887][   17.937887] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   17.953800][   17.953800] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   17.963051][   17.963051] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   17.972010][   17.972010] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   17.980988][   17.980988] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   17.989171][   17.989171] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   18.009905][   18.009905] xt_time: kernel timezone is -0000
[   18.032430][   18.032430] Error: Driver 'gt9xxnew_ts' is already registered, aborting...
[   19.788243][   19.788243] ======== XRADIO WIFI OPEN ========
[   19.795187][   19.795187] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31
[   19.803393][   19.803393] [XRADIO] Allocated hw_priv @ (____ptrval____)
[   19.813200][   19.813200] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[   19.840210][   19.840210] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[   20.050260][   20.050260] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   20.062758][   20.062758] [XRADIO] Detect SDIO card 1
[   20.073213][   20.073213] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   20.093157][   20.093157] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   20.119383][   20.119383] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   20.135394][   20.135394] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   20.159295][   20.159295] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   20.172219][   20.172219] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[   20.185470][   20.185470] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[   20.199392][   20.199392] mmc2: new high speed SDIO card at address 0001
[   20.207730][   20.207730] [SBUS] XRadio Device:sdio clk=50000000
[   20.223252][   20.223252] [XRADIO] XRADIO_HW_REV 1.0 detected.
[   20.273703][   20.273703] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[   20.315910][   20.315910] [XRADIO] Bootloader complete
[   21.014043][   21.014043] [XRADIO_ERR] xradio_firmware: wait for download completion failed. Read: 0xFFFFFFFF
[   21.025220][   21.025220] [XRADIO_ERR] xradio_load_firmware: can't download firmware.
[   21.034002][   21.034002] [XRADIO_ERR] xradio_load_firmware failed(-110).
[   21.042814][   21.042814] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success
[   21.163655][   21.163655] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   21.171759][   21.171759] [XRADIO] Remove SDIO card 1
[   21.171775][   21.171775] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   21.185540][   21.185540] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   21.193670][   21.193670] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !!
[   21.202023][   21.202023] mmc2: card 0001 removed
[   21.213388][   21.213388] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   21.231535][   21.231535] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[   21.244107][   21.244107] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[   21.254279][   21.254279] xradio_core_init failed (-110)!
[   21.263169][   21.263169] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   21.299296][   21.299296] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[   21.308775][   21.308775] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[   21.317076][   21.317076] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
kmodloader done
[   21.377217][   21.377217] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[   21.405391][   21.405391] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   21.414360][   21.414360] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   21.423298][   21.423298] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   21.432228][   21.432228] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[   21.440382][   21.440382] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B

柚木鉉

@jr_online 当然是用t113的重新编译了啊

柚木鉉

@jr_online d1s是riscv，t113是arm a7，怎么可能改个名字就行

柚木鉉

@fengshulin make kernel_menuconfig 里关闭xradio lpm

柚木鉉

@fengshulin

  │ Prompt: bash.......................................... The GNU Bourne Again SHell                                                                                                                   │  
  │   Location:                                                                                                                                                                                         │  
  │     -> Utilities                                                                                                                                                                                    │  
  │ (6)   -> Shells

柚木鉉

@fengshulin m menuconfig 查找 bash 把他关闭就行了，我自己适配了bash，下载的不适配

柚木鉉

@alvinlbl 检查uboot的屏幕初始化参数

柚木鉉

检查一下初始化initcode对不对，然后硬件RGB连接对不对

柚木鉉

检查固件实际大小看看是不是超了，tina的固件大小不等于实际大小

柚木鉉

@qinlinbin 找 @mangogeek

柚木鉉

烧写是量产卡还是启动卡，感觉刷成量产卡了

柚木鉉

可以用Cygwin解决这个问题，也可以用wsl

柚木鉉

可以参考下加入package里用tina编译

柚木鉉

@eddy_i 有可能

柚木鉉

没有添加 include 搜索路径 -I 指定下

柚木鉉

@jr_online 一样

YuzukiTsuru 发布的帖子